similar to: yellow alarm after weeks without trouble

Hi I have a Panasonic TDA600 conected with one E1 to the pstn and one PRI with my Asterisk using a Digium TE220B card. The Panasonic is master clock and Asterisk is slave, additionally the Panasonic takes the clock from the PSTN E1. This scheme works and I?m able to make and receive calls the problem is that some times the Asterisk lose the synchronism with the Panasonic and the log shows this

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

Hi All, I am getting these events in asterisk message log: NOTICE[16647] chan_zap.c: Got event 4 (Alarm)... NOTICE[16647] chan_zap.c: Alarm cleared on channel 1 after that asterisk exits silently until I restart it. Sometimes zapata drivers also get in a state where I need to physically restart the machine. Does anyone have any suggestions how to troubleshoot these alarm events? Roberts

Hi. I am using asterisk 1.4 (latest as of today) and zaptel 1.4 (latest as of today) and I cannot dial out using my 400P card with one fxs module and one fxo module. I am using kernel 2.6.24 and get the following log entries: [Feb 25 17:28:13] VERBOSE[25071] logger.c: -- Executing [s at macro-dialout-trunk:23] Dial("Zap/1-1", "ZAP/4/www411|300|wW") in new stack [Feb 25

Nik, This definitely helps! Please check your dial command. You've got "Dial(Zap/0/mynumber)" and I think you might possibly want it to be something like this: Dial(Zap/1/mynumber) or Dial(Zap/g0/mynumber) I don't recall there being a zap channel zero, but it is common to have a group zero. I would recommend trying Zap channel 1 - Dial(Zap/1/mynumber) - before trying the

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

I have searched for how to locate echo cancelation on SIP clients, but cant find anything and echocancel=y doesnt seem to have any effect. Configuration: CVS-HEAD from last month iPAQ h5500 with SJPhone (gsm/ulaw/alaw) Problem description: When I place or receive a call I hear a faint delayed echo of myself. The other party hears a really bad nonmuted echo that makes the call unusable. Aside

Hi everyone, I have been having some problems lately with our PRI and Asterisk, or maybe it is just me. It happens once maybe twice a day, but when some of our customers are calling in, the phone just drops on them. I pulled the information below from the log from one that happened. I notice why it is happening, but I can't seem to figure out a way to stop it from happening. I also

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

How would you categorize a Yellow Alarm sensed by the Asterisk side in a Legacy PBX integration? We have a Mitel SX200 connected to an Asterisk(1.2.4) with a TE110P. Twice today (first time in over a month) we received a Yellow Alarm on the TE110P. I have been able to clear it easily by restarting zaptel. Thanks in advance! -------------- next part -------------- An HTML attachment was

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Here is the scenario: Asterisk 1.14.13; zaptel 1.4.6; Digium TE120P (same problem with various previous versions; same problem with different TE120P cards). The customer has a partial (10 B-Channel) PRI that when it is busy (eight or more B channels in use), tends to fail as shown below... [Jan 26 23:00:31] ERROR[31893] chan_zap.c: Write to 28 failed: Unknown error 500 [Jan 26 23:00:31]

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

We have an asterisk box with the following configuration: - AMD Athlon XP 2400+ - 512 MB RAM - SUSE Linux 10.1 - a Digium card TDM400P with 3 FXO - another Digium card TDM400P with 4 FXS - asterisk 1.2.7.1 - zaptel 1.2.4 I already checked that those cards aren't sharing interrupts (by cat /proc/interrupts): 0: 14119786 XT-PIC timer 1: 10 XT-PIC i8042 2: