similar to: install-misdn compile problem with debian

Hi, I have an Asterisk 1.2.9.1 box connected to an ISDN line via a beronet card (with ports in PTP mode). I noticed a long delay when making outbound calls, more precisely between (taken from Asterisk CLI) "Called 1/XXXXXXXXX/s" and "mISDN/1-u43 is proceeding passing it to SIP/8-5486" I searched on misdn.org but found nothing. I'd like to understand if this delay is

Hi, I'm using Asterisk 1.2.1 on a Debian Sarge with a TDM400P and a monoBRI using chan-mISDN from beronet site. It seems to work all right except for autodial calls, monoBRI ISDN channel behaves differently waiting for the caller to answer and then continue. Asterisk console says: analog: -- Attempting call on Zap/2/3391818250 for 104@inbound_originate:1 (Retry 1) > Channel

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Hi all, we're buildin an Asterisk box based on an Intel IXP425 board. The board uses a Beronet BN2S0 ISDN card, mISDN 1.1.4 and asterisk 1.4.2. hfc_multi has been patched to compile under big endian cpu, and so also capi kernel files. All the modules seem to load correctly (configuration was made with misdn-init config), but when starting cha_misdn, asterisk outputs the following lines: P[ 1]

Hi, I have an Asterisk 1.2.9.1 box on a Debian distro with mISDN drivers. I installed the new driver (0.3.1-rc30) on our pbx but since no voice was passing I decided to go back to old version (0.3.1-rc23). Last friday everything seemed to work fine but now every incoming call drops after 3-4 seconds while Asterisk console is showing these messages: Apr 23 12:42:39 DEBUG[7625]:

... Activating "sip debug" shows the register packets but nothing in return. ... I think that this is a network related issue, but you have to solve it by using a Asterisk config file. Unfortunately I think that the faster way to solve your problem is trying to understand if sip messages are correctly sent to tnet. I strongly suggest to use http://www.wireshark.org/ previoulsly named

tnet.itand SIP register messages are not replied. I suggested to check if your Asterisk box is really sending SIP messages, you can use a net sniffer. Did you alerady used different sip client with the same sip account of your Asterisk box? Did you use zoiper from the same box? Marino p.s. Are you Italian? On Mon, Jul 14, 2008 at 5:27 PM, Giorgio Incantalupo < gincantalupo at

Hi, I am trying to use zaptel module on an Ubuntu 5.10 distro (2.6.x kernel) using gcc 4.0.2. Compilation does not give me errors so after a 'make install' I try to load zaptel module with insmod but the following error arise: *insmod: error inserting '/lib/modules/2.6.12/misc/zaptel.ko': -1 Invalid module format* Is there anybody who can help me?? TIA Giorgio --

Hi all, since Asterisk 1.4 seems to have too many differences from previous versions, wouldn't be nice to have a new mailing list? Giorgio Incantalupo

Hi, I'd like to build a personal PBX connecting 4 or 5 analogic phones with a ADSL line and I'd like to know what is the right card I need I visited digium site and I think TDM400 could be the right choice but I cannot understand how it works...I think it has 4 slots where 4 modules (FXS or FXO) can be inserted. How many cards do I need to connect my ADSL line to 5 phones? I think I

Hi, does anybody know what *zttranscode *module* *is for*?* Thanks!! Giorgio -- _________________________________________________ Giorgio Incantalupo, mailto:gincantalupo@fgasoftware.com FG&A srl - http://www.fgasoftware.com - Voice@Work - The Agile PBX http://www.voiceatwork.eu Tel: 02997663.14, Fax: 0291390172

This is a function of the Phone itself. Asterisk has nothing to do with it as it does not know anything about the call until after the SIP device 'sends' it. To my knowledge it is not posible. I don't even think a SIP standard is available for this. This 'feature' along with changing CallerID Display after a call has been answered is something missing from the RFC. >

Hi, we have an asterisk 1.2.1 box and 2 polycom SIP phones. We'd like to show the called name on the calling polycom display instead of his /her extensions as I do with the caller name on the called polycom. Is it possible? If yes, how? TIA Giorgio Incantalupo

pbx18*CLI> module load codec_g729-ast14-gcc4-glibc-pentium3.so Unable to load module codec_g729-ast14-gcc4-glibc-pentium3.so Command 'module load codec_g729-ast14-gcc4-glibc-pentium3.so ' failed. [Dec 22 15:52:45] WARNING[4491]: loader.c:757 inspect_module: Module 'codec_g729-ast14-gcc4-glibc-pentium3.so' does not provide a license key. [Dec 22 15:52:45] WARNING[4491]:

Hi, is there anybody who knows what this warning means?? WARNING[27309]: chan_sip.c:8875 reload_config: Section '10' lacks type TIA Giorgio -- ____________________________________________________________________ GIORGIO INCANTALUPO Tel. +39 02 9350 4780 (104) FG&A Software 20017 Rho - Via Puccini, 8 E-Mail : gincantalupo@fgasoftware.com Internet: http://www.fgasoftware.com

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hi, I live in Italy and I have an Asterisk 1.0.7 box with a HFC monoBRI card connected to my cisco router which is connected to FastWeb provider: does anybody knows why every time my cisco router turns off, my telephone connection to Fastweb drops (while internet connectior is ok)? Restarting Asterisk is worth nothing. TIA Giorgio --

There is no static interval. But i found out that it was my IP-Phone Service Provider that was having serviceproblems today. -----Opprinnelig melding----- Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne av Giorgio Incantalupo Sendt: 26. august 2005 11:33 Til: Asterisk Users Mailing List - Non-Commercial Discussion Emne: Re: [Asterisk-Users]

Hi all, I need to connect my Asterisk 1.4.26 with a Sangoma PRI card (configures with signalling=pri_net)) to a Cisco 2800 PBX. After connecting the cables everything seems fine (ifconfig w2g1 is ok, wanpipemonitor gives no errros, the span is up and active, green light on the card) but when I make a test with my iax phone, there's no way to dial the PBX and I get this WARNING: [Jul 2

Hi, every second I get on the console: Remote UNIX connection Remote UNIX disconnected which gives no problem but makes console unusable. Is there anybody who has encountered the same problem? How did you solve it? TIA Giorgio Incantalupo