Displaying 20 results from an estimated 3000 matches similar to: "Problem connecting PAP2 over wifi bridge"
2005 Aug 21
0
Using locked PAP2 and PAP2-NA with Asterisk
Here is some info that may allow some "locked" PAP2 and
PAP2-NA units to be used with Asterisk:
I have a PAP2-NA (from a provider other than Vonage) for
which I did not know the admin password, though the "user"
pages were accessible to me. The provider had set it up to
fetch at startup, its configuration file by HTTP from a
numeric IP. It was running 2.0.10(LSc).
A search
2006 Jun 06
0
Asterisk + Linksys PAP2-NA / Call Clearing
I have a handful of Linksys PAP2-NA's all talking nicely to Asterisk using
standard telephones. I've been running them for the better part of this
year. No complaints whatsoever. We chose the PAP2-NA's mainly due to cost
and especially the ease of provisioning.
In an effort to inexpensively bridge our office PBX (InterTel Axxess) to our
VoIP network, we've opted to connect
2004 Dec 23
1
Linksys PAP2-NA Config
Hi,
I have 3 PAP2 connected to *, they work fine but there are some things which I would like to improve, some of them are:
- double ring tone when placing a call (I hear two tones it seems like the PAP2 is generating it's own tone)
- some kind of noise (like glitches or something) when I pick up the phone (seems like some polarity thing)
- I'd like to keep the tone after
2005 Jun 03
0
PAP2-NA with Panasonic KX-TD1232 CE
Hello,
We use Asterisk with PAP2 and today we connected the FXS ports of PAP2
to CO ports of our Panasonic KX-TD1232. Problem is that Panasonic
doesn't ring - that is doesn't ring every time the PAP2 is ringing.
When we reset either Asterisk or the PAP2 it usually rings, but after
couple of minutes it stops and only the automatic operator is answering
- after 2 rings.
We tried changing
2006 Jan 13
1
linksys pap2 automatically connect on liftinghandset
The best I can do so far (which appears to be a bit of a hack) is
(<:0>S0), which says to add a '0' to the start of the string and dial
immediately. This gives asterisk an extension dialled of '0', which
isn't the 's' that i'd hoped for, but is a good start!
(S0) by itself doesn't work, nor does (<:>S0).
Any other suggestions?
Thanks
James
>
2006 Jan 13
1
linksys pap2 automatically connect on lifting handset
Is there a way to configure the linksys pap2 to automatically connect to
asterisk on lifting the handset (presumably into the 's' state)?
Asterisk would then be listening for DTMF tones to figure out what to do
rather than having to put a dial plan into each pap2.
I think the pap2 is pretty much the same inside as a few of the sipura
boxes so the same thing might work if anyone knows...
2011 Nov 30
1
Question on PAP2 linksys showing off-hook
I am using my first PAP2 device from linksys. Used many polycom phones...
I configured the PAP2 device with asterisk. I have the registration,
thought I was good to go.
Plugged in my Valcom 2924 public address analog connection, called the
extension
and I got busy... very strange I thought.
I then looked at the status page of the PAP2 and it says the following
Reg online and hook state OFF.
2005 Aug 30
0
canreinvite = yes with PAP2
Has anyone made this work? For me everything is fine until I switch
canreinvite form no to yes. What happens is that asterisk hangs on
"attempting native bridge" ... from what I understand "attempting native
bridge" means that the RTP is routed through asterisk (just without any
codec translation) But it shouldn't do that ... right? ... canreinvite is
set to yes ...
2006 Oct 30
0
Re: Linksys PAP2: calling tone stops after 5
>Message: 7
>Date: Sun, 29 Oct 2006 22:00:22 +0100
>From: "Jose Limeres" <jlimeres@gmail.com>
>Subject: [asterisk-users] Linksys PAP2: calling tone stops after 5
> tones
>To: asterisk-users@lists.digium.com
>Message-ID:
> <2b3431b20610291300u420116e5scf9103d7dac54321@mail.gmail.com>
>Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>
2006 May 04
3
number that starts with star on PAP2
We have some extensions in our dialplan that start with a star. We can
dial them from Zap phones and SIP phones, but not from phones connected
to a PAP2. After the user presses star follwed by two digits (our
extensions are dialed with star followed by three digits) he hears a
fast-busy that comes from the PAP2, not from Asterisk. This also
happens with the builtin *8 (call pickup).
In
2005 Feb 01
3
Linksys PAP2 / RT31P2 + multiple G.729 calls
Hi,
anyone can confirm if the Linksys's ATA and Router (PAP2-NA and
RT31P2-NA) have the same limitation of just one G.729 call like the
Cisco ATA 186 ?
I'm testing both appliances here and found this issue but could not
confirm this anywhere (nothing on the manual, no document or post from
any user about this).
In my tests they use G.729 only on the first call and G.711 on the
2006 Mar 07
2
pap2 Dial plan
Hi
i am using pap2 phone adaptors as clients to connect to asterisk server
i am able to make calls but i cannot access voice mail using phone
or start recording while call is in progress
and when i place a call to local sip extension there is a long pause ( 15
sec )
before the call gets dialled
i assume that the problem would be due to the dial plan in PAP2
if so please help me changing it
2005 Feb 16
2
Sip Notify PAP2-NA?
I am using mysql sipfriends and can't seem to get the MWI to work. From what
I've read it seems this is not supported with that dynamic system, and
probably never will be.
I was thinking of just setting a cron job or something to check every minute
for voicemail and set our sip NOTIFY messages as needed.
Also, the PAP2-NA has the ability to reboot via a sip notify and I would
like to be
2005 Mar 22
1
Mimicking Linksys PAP2?
I've got a Linksys PAP2 on my Vonage account with unlimited
usage, but my softphone-addon account only has 500 minutes. Anyone ever try
to setup their * to mimick the Linksys PAP2 ? Any comments or suggestions on
what problems I might run into if I try?
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2006 May 25
1
pap2 bridging problems
I'm having a real problem with one of my linksys pap2. On outgoing
calls the callee will ring, but caller (pap2) will not here it ring
When the callee answers, no audio is transmitted either way. Asterisk
reports the call connected and bridged correctly.
Now the kicker is that sometimes it works and other times it doesn't. I
have had the most luck calling land lines, but sometime
2006 Oct 29
1
Linksys PAP2: calling tone stops after 5 tones
Hi all,
I have a problem with the dialing tone in PAP2:
When making a call, I can hear the calling tone 5 times and then it
stops. The called party still hears the call but not the calling
party.
I've playing around with different parameters on the PAP2 web config
with no success until now. Anyone has seen the same probelm?
Thanks,
Jose
2007 Apr 06
1
pap2 - dtmf works when 'sip debug' is enabled
I am having an odd problem with a linksys pap2 ata and asterisk...
Asterisk won't detect digits from it until I issue a 'sip debug'. As
soon as I turn on sip debugging, everything works perfectly (classic
heisenbug)!
Asterisk is latest Debian 'etch' packaged 1.2.13. sip.conf looks like:
[mc_ext01]
type=friend
secret=ext01
context=mc_ata_in
host=dynamic
dtmfmode=rfc2833
2004 Oct 05
1
Dlink DVG-1120 Linksys PAP2 any Good?
I had just found a Dlink DVG-1120 on ebay and I'm curious if anyone has
used you it with asterisk. They were only $65. I have tested with the
Linksys Pap2 and found that box to be fairly nice except for a lot of
backgound/white noise. I was wondering if any else had experienced
that? Let me know if I've wasted $65 on the Dlink and also if you had
similar experience with white noise on
2005 Sep 02
0
STUN on PAP2-NA 2.0.12(LS)
Hello,
I'm having intermittent STUN trouble. Every one out of perhaps 5 reboots
the PAP2 contacts STUN ... on the other attempts it just skips that step all
together. I have been verifying this using ethereal which shows the
distinctive STUN server DNS lookup followed by about 10 STUN queries (when
it works - when it doesn't it skips all that including the initial DNS
lookup ...
2010 Feb 12
2
PAP2
I know this is slightly off topic, but I was wondering if anyone can help
with a problem getting my PAP2's to connect to Asterisk. I use a
provisioning file, and I recently re-wrote the files for each PAP2. I had
a small typo and the PAPs logged it as a corrupt file. I corrected the
file, however, Line 1 on both of the PAP2's now wont register. Line 2
works fine though. I've done the