similar to: IAX2 softphones can't (won't?) use PRI trunks....

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as

I've a call center using IAX softphones provided by a third party. We've observed problems where the IAX phones seem unable to use our PRI trunks. A sample anonymized call is provided below with the PRI debug calls embedded. Any thoughts, comments or suggestions would be welcome. In anonymizing it, I preseved the format and number of digits sent. -- Accepting AUTHENTICATED

hi,all when i send a call to other server use SIP trunk, i got this below, <--- SIP read from 222.46.18.52:5060 ---> SIP/2.0 403 Forbidden what's rong with is? > Asterisk 1.4.21.2, Copyright (C) 1999 - 2008 Digium, Inc. and others. > Created by Mark Spencer <markster at digium.com> > Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for

Hi, I use: Trixbox-2.2.4 FreePBX-2.3.1.0 Asterisk-1.2.17 BRIstuffed-0.3.0-PRE-1y-e Zaptel-1.2.19 ..with two ISDN cards, often but occasionally the dial out failed but is possible to receive external call. My zapata.conf conf is: [trunkgroups] [channels] language=it context=from-pstn signalling=bri_cpe_ptmp rxwink=300 pridialplan=unknown prilocaldialplan=local switchtype=euroisdn

i have a prablom here, i want to send a call from A to B use sip trunk , the call can sended B,but not work to PSTN. the message from B server. help pls,what's rong? > > <--- SIP read from 192.168.0.176:5060 ---> > INVITE sip:15921256331 at 192.168.0.151 <sip%3A15921256331 at 192.168.0.151>SIP/2.0 > Via: SIP/2.0/UDP 192.168.0.176:5060;branch=z9hG4bK51a51b96;rport

I just had a user report that they called out to someone on a cell phone this morning, and after a short conversation, the call was dropped/lost. The person on the cell phone says that this is very rare, and would not suspect the dropped/lost call to be on their side. I have looked at the asterisk/full log as thoroughly as I can, and have pasted the lines which seem relevant to that call below.

Hello, Sometimes the call gets answered for 1 second, but actually the phone has not rang, it?s just the CDR, and asterisk hangup automatically, I cought the log of 1 call like this, I hope you can help me with this. My setup is : <vendor> ----SIP--? <Asterisk> ?----IAX2---? <Asterisk with Dhadi channels> Here: -- Executing [966505103150 at from-internal:1]

I am using asterisk version 1.2.6 with Zaptel version 1.2.5. I have a POTs line coming into a Digium TDM01B. It appears to not be getting CID at all. If I hook up a POTS phone to the line CID comes through fine. Inbound and outbound calls work fine but there is just no CID on inbound for this channel.The incoming route for the channel is Zaptel Channel 0. No DID or CID settings applied. My IP

Hi Samba, I hope you are doing well. I run a cifs / nfs CTDB clustered NAS solution, and I find that when I reboot any of the nodes in the cluster, I must re-export the nfs mounts so they show up properly. Perhaps this is a general linux nfs bug and I am barking up the wrong tree, but I haven't found any problem / solution mentioning this as of yet besides my own known workaround

ERROR CONDITION --------------- -- Executing Dial("SIP/2001-f6c4", "SIP/2000|20") in new stack -- Called 2000 -- SIP/2000-0ead is ringing -- SIP/2000-0ead answered SIP/2001-f6c4 -- Attempting native bridge of SIP/2001-f6c4 and SIP/2000-0ead Have searched web and archive w/o good results. Thks in advance for any help, Dave sip.conf -------- [general] port =

Hello everyone! I've had this problem for a while and cant figure it out. When an outside caller calls an extension on my asterisk system, they do not hear any sort of ringing. Inside extensions calling other extensions do hear ringing. We have 3 other asterisk systems that are configured the same way, but do not have this problem. We think it has something to do with asterisk 1.6. The other

I have Asterisk 1.2.29, Zaptel 1.2.24 and Freepbx Setup for a queue up to 15 agents through a PRI line, it was working fine for more than 1 year, suddenly, when there is a load on the queue, the asterisk service disconnects and the calls are dropped. And the service starts again after few seconds, and so on. I am not using fax. I checked PRI by zttool and there are no alarms. The cdr logs

I have a problem calling a certain number from our PRI line. Calling the number from a separate PSTN phone works fine. The remote number seems to have some funny call redivert setup, when you call it, it answers immediately, makes some kind of beep and then starts to ring. Our PRI is in the UK from Telewest/NTL/Virgin Media and most outgoing calls work without a problem. The server is

Hello, I have a TDM400 and currently have 2 of the ZAP Trunks configured on it. Zap/1-1 and Zap/2-1. I am Running Asterisk@home Version 2.4 with AMP version 1.10.010 In my Outbound Routing I have the Trunk Sequence set up so that 0 is Zap/1-1 and 1 is ZAP/2-1 What I see is that when Trunk Sequence 0 is full, it does not open Trunk Sequence 1. I have found that this is true even if I

Hi people, I have the following dialplan, but it doesn't have the behavior that I think it should have. [default] exten => 2001,1,Answer exten => 2001,n,Dial(local/3005) exten => 2001,n,Hangup exten => 3005,1,Set(__RINGTIMER=10) exten => 3005,n,Macro(exten-vm,novm,3005) exten => 3005,n,Hangup When I execute the Originate (AMI) with the argument Channel=local/2001, It rings

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

Hi, i got Ubuntu 6.06 installed and theres a problem with asterisk. I've sucessfully installed it with the command: #apt-get install asterisk Then after installing FreePBX i get this error when restarting asterisk: root@hernandezz-laptop:/home/hernandezz# asterisk -rvvvvvvvvvv Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?) After looking at the logs i

hello, i have a FreeBSD 4.8-PRERELEASE #0 that i use as a gateway / nat box for my home. It also acts as a dns / mail server to the outside world. I'm using ipf and basically filter for bogus networks on the way in and out. I allow everything out keeping state, and allow this in: pass in proto icmp from any to any icmp-type squench group 200 pass in proto icmp from any to any icmp-type timex