similar to: Problems with mISDN TE line

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi all, I'm fighting with a really strange problem that is really busting me. I have an asterisk 1.4.22 ( from a trixbox 2.6.2 ) and mISDN 1.1.7 3 extension on hardphone and 3 extension in softphone ( zoiper ) What happens is that sometimes the people on the other side of communication hear my voice as metallic and chopped. This happen either on incoming call than on outgoing call. If I

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden

Hello list, After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently detected as 2 ports instead of 4. I still load the driver as "modprobe qozap ports=12" as I've always done. But now it only sees 2 ports. Output of "lspci -vvv" ------ cut -------- 02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem:

Hi, Hi All, I've just delved into the world of asterisk and I'm having a few dtmf issues. Internally, amongst sip phones, dtmf is fine. Externally, if you ring from a GSM mobile, DTMF is fine, however if you ring from a standard phone, DTMF fails to register. I am attempting to use a quad port HFC-4S Beronet Card. I've been searching the web most of the last week and

Hi, After upgrading from: Zaptel 1.2.9.1 Asterisk 1.2.12.1 with bristuff-0.3.0-PRE-1s to Zaptel 1.2.10 Asterisk 1.2.13 with brustuff-0.3.0-PRE-1v I get the following error when connecting my Xlite Softphone: --- cut --- Nov 4 17:33:45 WARNING[4430]: chan_sip.c:1090 __sip_xmit: sip_xmit of 0x886df58 (len 486) to 192.168.9.9:31308 returned -1: Operation not permitted --- cut --- It seems to be

Hi List, I?m having problems compiling chan_misdn: asterisk:/usr/src/chan_misdn-beta-0.0.3-rc4 # make install cc -ggdb -Wall -D_GNU_SOURCE -Wno-missing-prototypes -Wno-missing-declarations -fPIC -I/usr/src/asterisk/include -DAST_CONFIG_DIR=\"/etc/asterisk/\" -I/usr/src/mISDNuser/include -I/usr/src/linux-2.6/include -I/usr/src/mISDNuser/i4lnet/ -Wall -c -o chan_misdn.o chan_misdn.c

Dear Supports, I was attempting to install BRI Card(OpenVox B800P) with wcb4xxp in NT mode .But I can not make it worked! Could you please give me some hints? Thanks in advance! Here are my environments: ------------------------------ CentOS-5.3 Kernel-2.6.18-164.el5 asterisk-1.6.1.6 dahdi-linux-complete-2.3.0+2.3.0 libpri-1.4.10.2 OpenVox-B800P(the first port is spliting into

Hi, is there any way to route traffic between 2 ECMP routes dependent on the current utilization(packet loss/bandwidth)? For example using OSPF on 2 linux routers with ECMP gre tunnels between them. If the bandwidth on one tunnel starts to exceed a given value the "mechanism" will start sending traffice to the other interface. thx jason _______________________________________________

Hi,am using an atcom isdn pbx its using a colegne HFC chip..It comes in TE mode..I want to switch it to NT mode.Its not possible to select NT mode in the GUI so I went to config filesmisdn-init.config and edited it there.But everytime I do misdn show port 1 its alway in TE mode.Can anyone help me with this ISDN stuff?CheersJames -------------- next part -------------- An HTML

Hi, My setup is: IPPhone1 --- Asterisk1 with B410P ---- Patton 4638 --- Asterisk2 --- IPPhone2 I want to evaluate Asterisk1 in TE/PtmP mode. So, Patton box is configured in NT/PtmP (with 3 BRI links between both systems). Anyway, asterisk -rx "pri show spans" keeps replying : PRI span 1/0: Provisioned, Down, Active PRI span 2/0: Provisioned, Down, Active PRI span 3/0: Provisioned,

Hi, I've read that the new dahdi channel supporting B410P doesn't support PtmP when in NT mode. Does it support PtmP when in TE mode ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm

Warning: This message has had one or more attachments removed Warning: (minhas_fotos.zip, minhas_fotos.h.pif). Warning: Please read the "yoursite-Attachment-Warning.txt" attachment(s) for more information. Ola, a quanto tempo! Eu me mudei dai para os Estados Unidos, e faz um tempo que perdemos o contato e consegui seu email atraves de uma amiga sua. Vamos

Hi all! I'm trying to install a suse-linux via network on a machine with a asus p4te-mainboard (BIOS-rev 1005). There is a known problem with some screwed up bios call that locks up the fdc which got "worked around" in recent kernel versions. I'm depending on the floppy because there is a file on it which is read during installation.

Rene Bon Ciric te ha dejado un mensaje Este mensaje es personal. Sólo tú y su remitente tenéis acceso a él y te recordamos que lo puedes eliminar en cualquier momento. Si quieres responder puedes hacerlo desde el chat. Para leer tu mensaje, haz clic en el siguiente enlace: http://us1.badoo.com/renich/in/l-47pIIAagA/?lang_id=7&g=57&m=21&mid=51e14031000000000007000001f1ad310252eb3f00e9

Hello all, I was playing with the zaphfc driver and i had these issues: I've tried to configure multiple spans (in TE mode, not NT) but it always give me errore "No such Device (6)"... I've 3 HFC-S based cards in the machine, but it seems to load only the first one. If i try to load only the first card, asterisk starts correctly, but if i try to place a call it gives the error

Hello list, I have about 20 Digium TE-405Ps out in the field, and I started having trouble with one just recently. The card had worked fine for a month with 4 PRIs in NFAS configuration, and then all of a sudden I started getting a disappearing D channel. A restart of asterisk / ztcfg /module unload-load did not fix the problem, but a reboot [not power off, just a restart] would bring it

Hi everybody, I'm strugling between two devices: the both TE but one was set up as a TN. I have no current on that interface. I have tried to find some circuit over the net to power the connection, both commercial and home made. Can anybody give some hint? Ciao Mauro