similar to: OT:spa942 provisioning

Hello! I've upgraded from 1.2.9 to 1.2.14 recently but experience an unexpected behaviour with musiconhold: While in 1.2.9 musiconhold was playing continuous on sequential extensions after a timeout, it is restarted for every extension in 1.2.14: ;music starts exten => 902,1,Dial(SIP/phone1@proxy.com|5|m(mymusic)) ;music starts again exten =>

Hello all, I am using Linksys SPA942 in my current installation activity. I see a peculiar behavior: A call is made and the SPA942 uses its speaker. When the far end of a call hangs up , the SPA942 stays off hook, and after a time plays a fast busy. The user then has to press the line presence button to hang up the phone. I think I must be missing some sip.conf parameter. My sip.conf is pretty

Before committing to about 50 of the spa942's, I like to take a last poll from those on the list to identify any negative issues that might be associated with the audio, functionality, early failures, etc, on the spa942. Expecting to deploy these using existing cat5 cabling and both rj45 jacks. Been using three of theme in a short term demo with the customer, but the demo systems has

Am having a unique problem, calls received on my SPA942 seem to end after 15 seconds, but calls made from this device do not have this problem. For this device (when receiving calls) I get periodic "chan_sip.c set_destination: can't find address for host" I have set the "canreinvite=no" in the sip.conf. Does anyone have a sample entry from sip.conf for the Lynksys SPA 942

Fellow asterisk users, I am trying to get Single Line Appearance functionality working on a set of Linksys SPA942 phones and have not been successful. It looks like sla.conf is not getting read, only one phone reads as registered for the shared line, and a busy tone every time the shared extension is dialed. I have followed the documentation [1] and followed through other threads I saw

I'm using a bunch of SPA942's, and I'm trying to provision them mostly by DHCP (and what I can't set that way, I try to provision via HTTP interface into the phone). I changed the domain in my AstLinux config from "astlinux" to redfish-solutions.com, and set that in my sip.conf file as well: context=incoming

currently using 1.2.14 and zaptel 1.2.12 i'm using mfc/r2 so i can't move to 1.4 with sip jitter control and improved jitter control in zaptel 1.4. my problem is excessive jitter using linksys spa942. when i set canreinvite=no, which forces rtp to pass through *, quality is horrible. clicking sounds, pauses, etc. but when omitted or canreinvite=yes, sip to sip calls are ok. now, the

For someone that's network-aware, but hasn't sat down and plowed through umpteen SIP-related RFC's and memorized the standards, is there a good primer on troubleshooting SIP issues? I'm seeing a lot of NOTIFY/603 messages on my network between Asterisk and my Sipura 942's, for instance... Not sure what these are... perhaps the qualify keepalives? In which case, I guess

I installed SPA942 and SPA2101, and experimented with TFTP and HTTP provisioning. It all went smooth for many hours. But then all of a sudden it stopped reading configs from both from TFTP and HTTP. Now I am trying to troubleshoot and cant't find the problem. Once in a while, it does read from TFTP and/or HTTP, but then again, stops reading at all. My other phones, i.e. Grandstream and Aastra

Hellos, I need to send personal directory from asterisk to the ersonal directory of the linksys spa 942. Is this possible? -- Best Regards, James Mutuku Ndeti Agile Systems Limited +254722490994 www.agile.co.ke mutuku.wordpress.com Has your organization implemented a customer relationship management (CRM)system? visit http://www.agile.co.ke/crm.php and find out how our CRM can help you achieve

I'm running AsteriskNow 1.7.1 with a OpenVox 2/FXO/2FXS card, a Linksys SPA942 SIP phone and outgoing SIP and IAX routes. When I dial local PSTN numbers from the SPA942 using the FXO channels I observe a 5-7 second delay between when the PSTN number answers the call and when Asterisk connects the call at my end. There's enough delay time that I hear an additional ring after the PSTN

I'm running AsteriskNow 1.7.1 with a OpenVox 2FXO/2FXS card, SPA942 SIP phone and outgoing SIP and IAX routes. When I dial local PSTN numbers from the SPA942 using the FXO channels I observe a 5-7 second delay between when the PSTN number answers the call and when Asterisk connects the call at my end. There's enough delay time that I hear an additional ring after the PSTN number has

Hi, I have a strange problem. At a site where there are 20+ phones, there is one phone that cannot make outbound (to PSTN) calls. Each call is dropped after 20s with "no response to our critical packet". Calls to voicemail and internal extensions work fine. I understand that everything points to a NAT problem, but I don't understand how it could be because: 1) It does not affect

Hi, I'm running asterisk realtime, i had prob when a user does not unregister properly. I tested with SPA942 and a PAP2, when phone is registered, i call using the SPA using x-lite no problem, but when i unplugged the power, it does not unregister properly, so asterisk think SPA942 is still registered, when i call using x-lite, asterisk tries to call it.so it gets stuck at [Aug 11

I just bought an Aastra 480i CT for a client who needed cordless capabilities in their office. I'm trying to set up the base station and cordless handset in my office first. I'm able to connect the phone to my Asterisk box and make outgoing calls from either the base station or the handset - to extensions within my office as well as numbers outside the network. But I can't

Hi all, I need a fully developed web based remote provisioning system. I cant find anything reliable on the internet. Have already checked ataconfig.com and voxilla-ays.com. have tried to contact them but got no response. So if anybody knows a good provisioning system then plz tell me about it. -- Best Regards Rizwan Hisham Software Engineer Axvoice Inc. www.axvoice.com -------------- next part

Does anybody out there have any evidence that Sipura support is still in operation? rgds benjk -- Sunrise Telephone Systems, 9F Shibuya Daikyo Bldg., 1-13-5 Shibuya, Tokyo, Japan. NB: Spam filters in place. Messages unrelated to the * mailing lists may get trashed.

I'm getting "Got SIP response 406 "Not Acceptable" back from 10.0.1.2" occasionally when try to dial to SPA942 , anyone has any idea on this before i consider Firmware upgrade? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080326/2fd2c557/attachment.htm

hello, I would to define and unattended process to configure devices which are http-server-enabled, use DHCP but do not use TFTP-DCHP to configure themselves during boot. Has anyone worked on such subject ? I was thinking of something like : populating configuration file from device web pages (rendering this as generic and flexible as possible) writing a script which reads this file and set

Hy all of you, I've successfully installed a freepbx solution with 10 extensions : - 5 on Linksys SPA922 - 1 on Linksys SPA942 - 1 on Thomson ST022 Everything seems to work fine with all the hardphones excepts last week. The thomson has a strange behaviour. It can reach french mobile cell phones but when it reaches "fix" phones, the correspondant can't hear the caller. What