similar to: MFC/R2 problems

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the signalling "E" is

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hello! I'm tryuing to bring up an R2 connection but eventhough I've followed the guidelines in: http://zarzamora.com.mx/asterisk/17 something seems to be missing. When an incomming call is generated I get: Nov 24 06:01:17 WARNING[-197416016]: chan_unicall.c:612 unicall_report: MFC/R2 UniCall/24 <- 0001 [1/ 1/Idle /Idle ] Nov 24 06:01:17 WARNING[-197416016]:

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627

Hi, I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I can make calls over E1, but can't receive. Here the CLI when I make a call: -- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40", "Unicall/g1/91642208|50") in new stack -- Called g1/91642208 [May 14

Hi all I have MFCR2 successfully installed but seems to get warnings a s seen below when I start asterisk. Am running on Redhat 9. Asterisk Ready. *CLI> Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 far_unblocking_expired Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 local_unblocking_expired Dec 20 08:40:38

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi all, I still haven't seen my first post (cry for help) so I'm not sure if these are going through or not ... I've played with the box all day today ... I got it to quit seg faulting finally by playing with the config files. Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP) Here is my zaptel.conf: (I know the device connected to spans 1-3 are providing

Hello. I'm trying to setup MFC/R2 signaling, but chan_unicall fails at loading with this message: --- Unable to load module chan_unicall.so Loaded /usr/lib/asterisk/modules/chan_unicall.so => (Unified call processing (UniCall)) == Parsing '/etc/asterisk/unicall.conf': Found 061213-075938 ERROR[11454]: chan_unicall.c:3361 mkintf: Unable to open channel 1: Success here = 0,

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hi all, any body can tell me why i am receiving this message in my sever ? I have running * with 10 Digital Lines, but i am receiving a lot of times this message . Is a software issue or is a hardware issue ? Regards. Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:2672 handle_uc_event: Unicall/5 event Alarm Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:3091 handle_uc_event: Unicall/5 Alarm masks

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Dear Steve and *.* e1r2 developers and users; my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is : with version Fedora, C3 I have compile and run libunicall without problem, the testcall.c run also perfectly. and askterisk run without problem on the localm network. I patch asterisk in