similar to: Handling SIP 482 condition

I am a Linux sysadmin who has been tasked with developing the phone system for our nonprofit's new US headquarters building. We cannot bring our legacy phone system with us, so I am building this completely from scratch. I have already read "Asterisk: The Future of Telephony" and done a fair amount of googling. I am completely sold on Asterisk, and the new building's

Hi, Does anyone know anything about the following? In a hosted environment where several area DIDs are provisioned on a single server, how do most carriers establish the origination DID, number. Asterisk allows us to modify the CallerID, name, number and DNID channel variables before dialling out via SIP. Most carriers will allow us to spoof a callerID when placing a call, and pass it forward.

I need 100 DID's in a specific rate center (916-854-xxxx). How do I go about finding who owns the rate center ? If the DID's are available in this rate center ? Thanks Vikas

On Fri, Jun 29, 2018 at 3:40 AM Thiago Oliveira <cpv.thiago@gmail.com> wrote: > Hi Ales, > > I would like to prevent the guests from different subnets start a > communication. In other words I have the subnet 192.168.1.0/24 and > 192.168.2.0/24 and the guests from 192.168.1.0/24 cannot reach/talk with > guests on 192.168.2.0/24 at the same host. Is this possible using a

I am thinking about a change to our company's phone "layout" and would like to get comments from people who have done something similar. Currently, we have 3 locations - each with their own Asterisk PBX. The corporate office has a PRI. Each remote location has a SIP provider for 5 channels of SIP going to their own PBX. Interoffice calls use the PSTN. Most inbound calls come to

Hello, I would like to make filter that allows communication only between specified VMs. Those VMs should be specified by their MAC address. The filter should extend clean-traffic but I was not able to get it working with that reference. I have came up with modified clean-traffic which works fine [1]. Is there a way to achieve the same behavior with reference to clean-traffic? Thank you. Best

I'm curious what asterisk solutions there are out there for inbound call centers with multiple DIDs. I'm looking for solutions for a setup where single system may have 1000 DIDs going to it, one for each account. Each account may not get that many calls. Solutions that will all reporting on calls coming into different accounts, call routing for queues based on distribution groups. Like

I have been looking at moving from SIP-based DID (Illinois) providers to one that uses the IAX protocol for DIDs. After a search, I've come up with the following: http://connect.voicepulse.com -- $8/month, many rate-centers http://www.iax.cc -- $1.50/month + 0.014/min, many rate-centers Can that be all that there is? I like the pricing plan at iax.cc, because it would allow me to set up

I had the same problem. If you are not using virtual machines then # systemctl disable libvirtd works and is easily reversible. Alan On 18/04/2020 23:03, Alessandro Baggi wrote: > Il 17/04/20 11:01, Alessandro Baggi ha scritto: >> Hi list, >> >> I'm studying nftables. I'm using CentOS 8.1 (Gnome) and I disabled >> firewalld. I noticed that a default

I am currently working on an Asterisk test system, and will be presenting a demo to the Board of Directors tomorrow night. I want to make sure I have all of my ducks in a row. The Asterisk system will be used to replace a Norstar MICS. The location has two PRI's coming in, with a few hundred DIDs. I know how to make * use the DIDs incoming, and I know how Nortel uses the DIDs. Now for the

I want the ability to setup DIDs in a variety of different remote locations in Canada. There are various providers that have DIDs in major cities, but none that focus on the "smaller" cities. The question is how do I actually setup these DIDs? Thanks, Geoff

Hi - I am looking for suggestions for ITSPs for faxing with asterisk 1.8. We are based in the US, so would need an ITSP with US DIDs. #1) We would like to use Fax For Asterisk with asterisk 1.8.4 in order to receive faxes via T.38. Sending faxes is not a requirement. Does anyone have a working asterisk 1.8.4 configuration and ITSP provider that they can recommend? We have been trying T.38

I have several toll free numbers that get forwarded to a single local number assigned to a trunkgroup. I've asked the telco to not forward those toll free numbers but to assign them as DIDs to the trunkgroup, so that I can differentiate via DNID. They said that they can't do that. That toll free numbers must forward. I know that I could have them each forward to different local DIDs

Hello, I have a nwfilter that I'm using to ensure that libvirt domains can't spoof IPv6 traffic. It looks like this: <filter name='no-ipv6-spoofing' chain='ipv6-ip' priority='-710'> <rule action='return' direction='out' priority='500'> <ipv6 srcipaddr='$IPV6' srcipmask='$IPV6MASK'/> </rule>

Anyone running caller id spoofing applications in the USA running asterisk? Then it's time to move them to Canada or similar. http://arstechnica.com/news.ars/post/20070627-caller-id-spoofing-about-t o-be-outlawed.html Regards, Dean Collins Cognation Pty Ltd dean at cognation.net <mailto:dean at cognation.net> +1-212-203-4357 Ph +61-2-9016-5642 (Sydney in-dial).

Hi List, I recently signed up with Voxbone to get some International DIDs. I was just about to purchase a DID this morning... but when I went to get it.... voxbone wanted the end user's address information. So I started to put it in... unfortunately... the end-user is in the U.S....but the only options are for a few select cities in GERMANY! I don't understand. Is there some

Following the successful deployment of asterisk servers at several of our branch offices, in the near future, I'll likely be implmenting an asterisk server at our HQ. We currently have a T1 PRI terminated on a legacy PBX. I'll be doing a stepped deployment in which, via a dual T1 linecard, the asterisk server will initially pass all incoming/outgoing calls directly through to the PBX.

Hi all, All of a sudden all my IAX DIDs have gone down. I couldn't find any reason other than that the ISP is blocking port 4569. DIDs register fine from my home server, but not from office server, which is not behind any NAT. SIP registers fine. I am trying to change IAX port but it apparantly IAX works only on 4569. Changing it in iax.conf doesn't do anything. Changing it is

Hello, our gateway receive incoming calls from an outside gateway for multiple DIDs. For some of them we want fax detection, for other no. To do so, faxdetect is set to yes, but how to disable the fax detection for a specific incoming DID? For those DIDs, we just want to forward the call to a real fax machine DID which will do the job. Thanks for any hint Regards -- Daniel

I would like to setup a system with two tennants with two seperate DIDs through one IAX provider account. Is it possible to route the calls into different contexts based on the DID dialed? I have searched and found nothing. I do not see anywhere in the console that says what DID was dialed so I am thinking two seperate accounts are needed to make this work. Can anyone confirm? Thanks