similar to: bridging calls on a samsung pbx from asterisk

Hi, I've now set up Asterisk to interface with our current Samsung iDCS 100 PBX via an 8SLI analogue extension card in the Samsung and an Openvox A400P04 4-FXO card in the Asterisk box. It all works in that I can place calls in both directions from the office Samsung extensions and Asterisk SIP extensions. The only tricky bit was getting the FXO to detect hang-up from the Samsung correctly -

Hi, Having Asterisk-0.4.0 with 2FXO port and Samsung SKP 816H PBX in 2 offices. I am able to make call between two offices. But the problem is that call dosen't hangup. Office A [Asterisk+2FXO+SamsungPBX] <------------- I A X ------------> Office B [Asterisk+2FXO+SamsungPBX] Configuration files are given here.............. ------------------------ zapata.conf

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

I was incorrect in a previous email... The situation in question is this: Asterisk <---BRI---> PBX <---BRI---> PSTN There are Samsung extensions on the PBX and SIP extensions on Asterisk. I want to be able to use TAPI to initiate dialling, and the PBX has no such feature so Asterisk must initiate it. For an Asterisk initiated call from a PBX extension to a PSTN number, this works as

Hi, Firstly, I'm new to Asterisk and am a system admin rather than a phone engineer. I've googled and read around but haven't been able to answer my questions sufficiently to buy hardware and get this thing set up. Secondly, if I've missed vital information from what is below, please let me know what. Onward...: So, what I'm trying to solve us remote working. We're a

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hello I'm trying to install Dahdi through source code on a Fedora 13 host to use an OpenVox PCI card with a single FXO port, but dahdi_cfg -vv isn't happy. 1. After successfully running "make all; make install; make config", I edited /etc/dahdi/system.conf thusly: loadzone=fr defaultzone=fr fxsks=1 2. Then ran "dahdi_cfg -vv" which says: ------------- DAHDI Tools

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac

Hi, I'm planning to buy a new ISDN-PBX (I hope this is the right term for an ISDN phone system). I would also like to connect it to asterisk. As far as I know there is no ISDN card where I can connect an ISDN-Phone to directly working together with asterisk (please correct me if I'm wrong). So what I was thinking of doing was to get a regular ISDN PBX and add a second internal S0 bus

Hi all I've got a setup where I use a Sangoma PRI card driven via Sangoma WanPipe to connect to a legacy Samsung PABX (I'm not sure which model) form Asterisk 1.8.11.0. The reason is the customer has a large installed base of Samsung phones physically connected to it and on each users desk. They did not want to spring for a complete replace of all their Samsung phones with generic, and

I have a Samsung M800 phone that I had (wrongly) assumed would show up as a USB drive on Linux so I can transfer files to it and so on. Instead, it appears to present itself as a modem. Is there any way to make it appear as a usb drive? Dec 1 13:47:17 mutt kernel: usb 5-1: new full speed USB device using uhci_hcd and address 3 Dec 1 13:47:17 mutt kernel: usb 5-1: configuration #1 chosen from

Hi, I am having some trouble with ISDN Dialout. Using a Netjet-s PCI Card. When in Minicom, the only way I can dialout is if i issue ATS18=1 First. Otherwise I get a BUSY message. So thats fine. But when I dialout from asterisk, I get an immediate hangup, so my guess is that asterisk is not issuing ATS18=1 to the ttyI device. Here are my configs, any input would be greatly appriciated.

Call us on +91-9666 4000 48 - Mobiles <http://www.fosila.com/mobiles> - Cameras <http://www.fosila.com/cameras> - Laptops <http://www.fosila.com/laptops> - Bags <http://www.fosila.com/bags> - Watches <http://www.fosila.com/watches> - Toys <http://www.fosila.com/TeddyBears> Dear *User*, Unbelievable offer Limited stock. Grab it!! Samsung

Does Asterisk support Radius accounting?.... -----Mensaje original----- De: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] En nombre de asterisk-users-request@lists.digium.com Enviado el: Lunes, 17 de Noviembre de 2003 12:08 p.m. Para: asterisk-users@lists.digium.com Asunto: Asterisk-Users digest, Vol 1 #1912 - 11 msgs Send Asterisk-Users mailing list

I tried to setup an PBX System with the following parties: 1. SIP Phones 2. One AVM ISDN Card with CHAN_CAPI for Outbound dialing and receiving external calls 3. One HFC-S PCI Card in NT-Mode with ZapHfc for physical ISDN Phones. 1+2 work perfect I have problems with part 3 Card is working, drivers loading fine, asterisk initializes chan_zap without problems. Demo did work. My problem is

Hi With my phone, Samsung delivers NPS software (New PC Studio) I can install it with Wine 1.3.26 on my Ubuntu 11.04 but when I try to run it, I get a lot of messages: Code: remy at remy-PC:~$ wine "C:\\Program Files\\Samsung\Samsung New PC Studio\\NewPCStudio.exe" err:ole:CoGetClassObject class {dee35070-506b-11cf-b1aa-00aa00b8de95} not registered err:ole:CoGetClassObject no class

Hello everyone, On February 8th, Samsung's Advanced Computing Lab will be meeting up with Compiler Engineers in the SF Bay Area. You will be able to learn about our home-grown mobile GPU and explore employment opportunities. Our compiler team uses the LLVM compiler framework to develop compilers for this GPU. Click this link for more info about out San Jose MeetUp on February 8th:

On Fri, 17 Feb 2017, Joseph L. Casale wrote: >> [root at localhost yum.repos.d]# mtp-detect >> libmtp version: 1.0.1 >> >> Listing raw device(s) >> No raw devices found. > > Does your phone have a usb setting for phone versus mtp mode? I think it doesn't. >From dmesg: usb 2-2.4: USB disconnect, device number 10 usb 2-2.4: new full speed USB device

Hullo :) Can someone help me untangle a bit of a mess? I'm trying to set up a demo * server to show off how useful it can be to our business (as an IVR system and VoIP backup if our ISDN30s fail). I've not been able to get NT mode working with our InterTel Axxess PBX, so I've resorted to using normal TE mode and working on the basis the people dial one of the ISDN BRI extension