similar to: G.726 on Asterisk 1.4.0

Ok, With everything restore on rtp.c, still I have no audio however the call is not destroyed immediately as before. I'm going to put a second Granstream box, and findout if between two boxes this happen too. I cannot believe that we cannot do 2 g726 on the same box at one time. Carlos -----Original Message----- From: Carlos Alperin [mailto:calperin@senecacom.net] Sent: Wednesday,

Since nobody answer my previous question (It looks like g.726 is a bad word). I have this scenario: One box with Asterisk 1.4.0 beta 2 IAX to anothers Asterisk working properly. As an ATA I have only one Grandstream HT496. Two lines on the ATA 727 & 726. >From outside I can call any of those two extensions if: I defined both as ulaw (G.711) One as ulaw and the other as G.729

I tried to test Asterisk 1.4 on FC6 x86_64. I have it working on FC5 x86_64 very good, but since FC keeps updating, I tried to follow newer kernel versions. I can't pass the zaptel compilation. Everything is OK, but when I finished, and tried to load it, allways got module not found when I run modprobe zaptel, and modprobe ztdummy. I already tried to modify is with the sed 1 option but

I finished to try to install Asterisk Now 1.4.0 on an AMD 3800 dual processor machine. The install lookups on the search for the Sata drive, since however it loads the sata_sil driver it doesn't work. Did someone knows what version of Linux is using on Asterisk Now? Thanks, Carlos Alperin -------------- next part -------------- An HTML attachment was scrubbed... URL:

Yes, I can call the phones, they ring, etc, and call call out, just no outbound audio. Is their any difference in the inbound & outbound audio streams in Asterisk that could cause it, e.g., different ports, protocols, connection/discovery methods, etc? Thanks, Ross ---------- Original Message ---------------------------------- From: "Carlos Alperin"

This issue may sounds trivial I need to build a Router for send Internet + VoIP traffic. The computers are in a different network that the Phone Gateway. The Computers are going to be send to a 3 Mbps connection using OSPF, in the meantime the phones are going to be send to a T1 using OSPF too. The routing software is going to be Zebra. I need to switch the outgoing in case that the T1 or

To me it's a error if I can't complete calls using the ATA configured to use the g726 codec. I just tried it usign a sipura SPA-2000 (preferred codec: G726-32) and I received NOTICES and WARNINGS, but I can't complete a call. On a zap channel: -- Executing Dial("SIP/2007-e4d8", "Zap/1/2217008") in new stack -- Called 1/2217008 -- Zap/1-1 answered

I have a ATA 186 with SIP firmware 3.1 when I changed the configurations to use the g.726 codec I received many erros and the calls doesn't work. I changed the fields: - LBRCodec: 6 <- the code for g.726 - TXCodec: 6 - RxCodec: 6 The errors: Jul 9 13:15:37 NOTICE[1192491824]: rtp.c:500 ast_rtp_read: Unable to calculate samples for format G726 Jul 9 13:15:37 NOTICE[1192491824]:

I am thinking of getting an asterisk user group together for either SE Michigan or just Metro-Detroit. How much interest in asterisk in Michigan is there on this list? I am already on the board of glimasoutheast, with is a group for technology professionals. (very broad range) It is a spin-off from Automation Alley, which is SE Michigan's version of Silicone Valley. -- Steven

Dear All, I need to bind two different ports at the same time for SIP. 5060 and another port number. Is it possible ? It would be something like port=5060,5062 Isamar

Good evening. I just wanted to take a minute and review my experiences with some of the SIP devices out there on the market. I hope this post will help newbies or someone considering a certain device. I would appreciate any other input on either the devices I am "reviewing" or other devices that I didn't! These devices are deployed in our primary line and small PBX replacement

Roman: I created two bash scripts called Mail2Fax and Fax2Mail for use with the asterisk sever. They leverage the app_txfax and app_rxfax scripts, along with ast_fax. They make using these apps a lot easier, including being able to mail to fax@domain.ca for outgoing faxes and then extracting phone numbers from the subject line! (Makes it easy to use with Sendmail without complex rules /

Hello folks, I've did some tests with different phones and Asterisk last two days and here are some results, which I want to share with audience. Cisco's 79xx and Sipura's phones/adapters on INVITE always reply with their preferred codec. So, for example, if Cisco's/Sipura's phone has preferred_codec g729a(18) and it receives INVITE from UA which has preferred codec

Dear all, I am doing an interop testing with asterisk-1.6.0.5 now, and I have a question about the G.726 codec on asterisk. While my IAD supportes G.726-16,24,32 and 40 codecs, when doing a testing about G.726-40, I found that asterisk removed the G.72-40 sdp attrib when transmitting the INVITE with SDP. I modified sip.conf in order to solve the problem, G.726-32 is ok when allow=g726, but

I have been looking at the medium-rate codecs in Asterisk - ADPCM and G.726. Both of these are adaptive PCM codecs - the G.726 one is a little more expensive in processing power, however both are 32k bit-rate. I am experiencing problems using G.726 where the audio level is high. It produces loud clicks as if clipping. For quiet audio however, it seems fine. ADPCM (Digilogic VOX?) seems to be

Hi, I have both codec_g726.so and format_g726.so loaded: root at test:~# asterisk -r -x "module show" | grep 726 codec_g726.so ITU G.726-32kbps G726 Transcoder 0 format_g726.so Raw G.726 (16/24/32/40kbps) data 0 But when I try to dial into Asterisk with Twinkle softphone using G.726 codec: INVITE ..... [SIP headers omitted] v=0

Hi there everyone! I've bought a Sipura SPA 3000, and succesfully connected it to my Mac, where I installed Asterisk 1.4.0. Both ports (FXO and FXS) are well configured). However, living in Brazil, I'd like to know if there are optimal settings to my PSTN that I should enter into the config of the device. I experience a little bit of echo on the FXO probably because I raised the gain of

Hi all, i have a problem with 2 peers conecting to an asterisk machine, both are conected behind nat without any port mapping in the router, and the * is conected behind other nat with the port 4569 mapped to it address, the problem is: when a peer register to the asterisk the other cant register and viceversa, only gets registration the first one, im using firefly and a hardphone from wuchuan,

Hello Everyone, This is my first post, and this is my problem :-). I have a asterisk@home, work excellent (only internal users), but i need outbound calls. One person give me an access to his "Cisco 5300 Media Gateway", he give me a dial rule and the router ip address. I've created a SIP Trunk, and a outbound routing, with all the info (the rare thing, the

I need to find someone to work with me in the Grand Rapids Michigan Area. Someone good with Linux and Asterisk would be ideal. Please get me contact info if you are interested. Thanks Tim -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050831/315eff3f/attachment.htm