similar to: zaptel, bristuff zaphfc, and florz question

After upgrading a CentOS 3.x box to CentOS 4.1 (both x86_64 with an Athlon64) I also wanted to get the latest bristuff. Unfortunately bristuff without florz causes the box to kernel panic within hours (console will complain about bad frame received something). It seems however that the florz patch will not work for x86_64 arch. Bristuff -0.2.0-RC8j compiles fine without the florz patch, but

Again trouble compiling bristuff-0.3.0-PRE-1q with the florz patch on a x86_64 box (I guess nobody is using x86_64 platform or is able to fix this themselves?) First of all when bristuff is downloaded and compile is started it appears that the bristuff Makefiles are badly broken. The asterisk Makefiles all do see to find the kernel sources on a RHEL4 box in the proper directory, the pure

Has anyone had any success using the Florz patch for zaphfc ? I have a * system with 2 HFC cards which is working fine with 2 PTP ISDN lines however the users are complaining of crackles on the line which I am assuming is related to the IRQ issues raised by Florz. I have tried to use the patch but it errors trying to patch zaphfc.h Any help would be appreciated. Regards, Stuart -- No virus

I applied the florz patch but my problems remain. Now I get all sorts of weird errors on the console and I cannot make outgoing calls. Incoming calls work as expected. I am using a single HFC-S card with BRI. Any clue what these errors below are? Ri = 44651 TEI msg = 3 TEI = 7f Ri = 3800 TEI msg = 3 TEI = 7f Ri = 42399 TEI msg = 3 TEI = 7f Ri = 42409 TEI msg = 3 TEI = 7f Ri = 22078 TEI msg = 3

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Caller id is not in the configs that are supplied with zaphfc from bristuff, and it's not mentioned in the wiki. Is it possible to use callerid with zaphfc/bristuff? Thanks!!

Hi, I'am having some problems with new mainboards and 3xHFC-S cards. The the first problem was with interrupts, I mean if HFC-S card was using interrupt i.e. 21 or higher - it didn't work. Solved by disabling APIC. However, still the driver behaves a little bit strange. If card 0 & 1 is TE and 2 is NT, TE works fine, but NT is not working at all. If card 0 is NT and 1 & 2 TE - all

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Hello * users I've problems with sound quality on zaphfc Asterisk works fine good sound quality. If I do "make load" in the bristuf.xx zaphfc dir then sound quality drops directly. Even if I don't load the chan_zap in the modules.conf I use this config on more (even old 400Mhz machines) and works correctly. Looks like an hardware problem but I can't find it. I don't

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

Does anyone test Asterisk 1.2.X + bristuff-0.3.X and TDM card? We can't get it to work. -David -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Julian J. M. Sent: Friday, March 31, 2006 1:44 AM To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Re: BRI

I have ISDN BRI line (Point-to-multipoint), with HFC card and bristuff/zaphfc driver. I also have TA attached to NT, with analog phones and modem on it. When I'm dialling through Asterisk/bristuff, and in the same time TA have some conversation (or maybe modem link) on channel 1, I can hear that conversation (or modem) very short period (0.2sec), and I also disturbing that conversation

Maybe this is rather a hardware question, but I am posting it on this list because the probability of someone else of you having tried this is greater here than other places I can think of. I have an ISDN card that is setup in NT mode using the zaphfc driver in bristuff, and I got it working perfectly with one ISDN phone using a crossover cable and 100 ohm termination at the end of the cable.

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make

Kapejod is working on a fix for the CDR problem in bristuff. See below ----- Forwarded message from kpj@junghanns.net ----- Resent-From: tzafrir.cohen@xorcom.com Resent-Date: Fri, 10 Feb 2006 13:01:25 +0200 Resent-Message-ID: <20060210110125.GU16880@xorcom.com> Resent-To: tzafrir@cohens.org.il Envelope-to: tzafrir.cohen@xorcom.com Delivery-date: Fri, 10 Feb 2006 05:19:50 -0500 Date: Fri,

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

Hi, I have following problems compiling bristuff-0.2.0RC8m. Has anybody seen them before and can point me in the right direction? zaphfc/make all: ---------------------- /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c: In function 'hfc_findCards': /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c:1000: error: invalid lvalue in assignment make[2]: *** [