similar to: chan_unicall.c isntallation problem

Dear Steve and *.* e1r2 developers and users; my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is : with version Fedora, C3 I have compile and run libunicall without problem, the testcall.c run also perfectly. and askterisk run without problem on the localm network. I patch asterisk in

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I downloaded and installed the files in the follwing sequence spandsp libsupertone libunicall libmfcr2-0.0.3 is

Hi, Anyone there could figure me out on how to install my unicall. I followed the instruction below in the stated site at; http://soft-switch.org/unicall/installing-mfcr2.html. Questions: 1. On what directory/folder should I copy the chan_unicall.c, channels_makefile.patch? 2. On what directory/folder should I command patch < channels_makefile.patch? 3. On what directory/folder should I

Hello! I'm tryuing to bring up an R2 connection but eventhough I've followed the guidelines in: http://zarzamora.com.mx/asterisk/17 something seems to be missing. When an incomming call is generated I get: Nov 24 06:01:17 WARNING[-197416016]: chan_unicall.c:612 unicall_report: MFC/R2 UniCall/24 <- 0001 [1/ 1/Idle /Idle ] Nov 24 06:01:17 WARNING[-197416016]:

On 8/23/07, sanchal.singh at alliance-infotech.com Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I

hi all, this message is destinate to users who rub libunicall on asterisk succefuly ... my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is as follows: with version FC3 I have success to run libunicall without problem, the testcall run perfectly well. askterisk run without problem on the

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I

Dear HO SIN, many thanks for "L" solution you give me... I have also libtiff troubles with RH9, how did you resolve them ? R2 protocol I use work only with AB bits(CDbits ares fixed) and it run perfectely with the testcall.c, i'll try with chan_unicall and i'll give you the result... *** GOOD luck Steve for updating the patch of last asterisk *** thank you for your help

>any feedback would be awsome, the idea is to fill in the 30 channels of >the E1 all at the same time and see how stable it can be > > ----- Original Message ----- > From: "Miguel Cavazos" <miguel@cavazos.com.mx> > To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" > <asterisk-users@lists.digium.com> > Sent: Wednesday,

Hello again :-( I have a problem with chan_unicall. If I have two simultaneous incoming or outgoing calls, they sound broken because cpu load goes to 99%. Also with one call, the cpu load goes to 99%. Seems like device /dev/zap/channel is busy after 5 or 10 seconds , and chan_unicall does not write to this. strace with asterisk-1.0.7, zaptel-1.0.7, kernel-2.6.10 ================================

Hi Kaws, I may need to add some notes; 1. The default .rpm version of libtiff in RH9 does not seem to contain some functional entries required for libunicall / libmfcr2. Therefore when compiling libunicall "unresolved references....." will happen. To solve this, I needed to recompile libtiff from the tarball. When installing libtiff, the default directories will be under

Hi, I have installed chan_unicall for MFCR2 on Asterisk 1.0.7, 1.0.5 and 1.0.4. - 1.0.7 does not send dtmf properly through unicall channels from sip snom phones on any mode (rfc2833, info, inband) - 1.0.5 and 1.0.4 are able to send correctly the dtmf tones when configured to INFO in sip.conf. Could this be a problem inside 1.0.7 when paired with libunicall ? Either version I am using, the

Hi All, I have installed chan_unicall and MFC/R2 successfully, and is runnign fine. But I noticed that once unicall is installed, asterisk CPU usage as reported by 'top', jumps to 99% every few seconds. I have no incoming calls, and I have even removed the E1 lines from card and I tried almost everything possible but I was not successful in determining the cause of this high cpu

Hi, I have successfully installed libunicall and mfcr2 in Venezuelan variant. We are able to receive, make calls without any problems. When we place a call from a snom sip phone through chan_unicall and press a dtmf (either using info, rfc2833 or inband) Asterisk seems to get the order of playing dtmf but a garbage is heard at the other side. I have been trying to narrow down the problem on

Hi guys, I have one E1 with 30 channels in Mexico City, I guess that if i can fill this 30 channels with REAL traffic for 2 or 3 days I can find new bugs on chan_unicall or I can see how stable it can be. Im using R2/MFC with chan_unicall the patch that Steve Underwood wrote. I will let anyone make FREE LOCAL calls to Mexico City till saturday or maybe until monday to see how stable this can

I have a problem with inbound and outbound calls in asterisk. I read previous thread, and then test new versions of unicall, but I don't have success, the problem persist. The system suffers CPU peeks with a single conversation, with an interval of 5 or 10 seconds. My system has: asterisk 1.0.5 zaptel 1.0.4 libunicall 0.0.3-pre3 hardware: E100P Also, I made traces with strace, but all

I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call

Hello all. How to compile chan_unicall.c i have problem when compile chan_unicall.c, error message please help gcc -c -pipe -Wall -Wstrict-prototypes -Wmissing-prototypes -Wmissing-declarations -g -Iinclude -I../include -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DZAPTEL_OPTIMIZATIONS -DASTERISK_VERSION=\"CVS-HEAD-05/28/05-06:39:38\" -DASTERISK_VERSION_NUM=999999

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627