similar to: asterisk misdn incoming line not working.

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hi, I have switched a while back from chan_capi to chan_misdn. When the number is dialed and the phone is then picked up everything works just fine. Some users however FIRST pick up the phone and then start to dial... I did not get this to work with misdn. When two digits have been dialed, asterisk sees the extension as complete and does not wait for further digits. I am using an midsn NT

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi list, I've installed Asterisk 1.4.0 with newest mISDN 1.0.4 + mISDNuser 1.0.3 on Fedora Core 6. I get many compilation error on mISDN. It wants to include linux/config.h That I fixed by removing the #include line at every occurance. (Don't know if that was a wise move, but it then compiled). mISDNuser and asterisk compiled fine, and asterisk can find and use the ISDN BRI port in

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hello. I have a strange problem with the MeetMe application. Configured is a misdn msn to go into a preconfigured MeetMe room. exten => 12,1,MeetMe(1234,pIM) The first caller gets the prompt to enter the pin and then gets connected to the MeetMe room. The second caller gets also the prompt but after entering the right key he hears a dialtone followed by the message: The number you have

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

Quick question: Is there a way to distinguish between calling MSN's when using chan_misdn? More info: I've got my ISDN2 (EuroISDN) up and running here in Romania with 1 base number plus 5 MSN's. Now I want to my * to do different things when receiving a call on from different MSN's (like forwarding the call to my FAX machine or forwarding the call to my mobile). The obvious way

Hello, I would like to put 1 asterisk box in Country A and 1 asterisk box in Country B. Let's assume : - Asterisk box in country A = GWA - Asterisk box in country B = GWB - Calling party number (located in country A) = CgPNA - Called party number (located in country B) = CdPNB - Second Called party number (located in country B) = sCdPNB - PSTN in country A = PSTNA - PSTN in country B = PSTNB

Hi I try to connect my asterisk with a Siemens Hicom pbx. I have a PCI cologne Chip card wich support NT mode. I have compiled mISDN driver, and I use chn_misdn from debian package. The card wotk fine in TE mode but mot in NT mode. for informations : routeur*CLI> misdn show stacks BEGIN STACK_LIST: * Stack Addr: Uid 40200001 Port 1 Type NT Prot. PMP Link DOWN --> bchan: addr 0 channel

I have set up a * box with two hfc ISDN pci cards using mISDN both in TE mode with PmP mode. (using $MODPROBE hfcpci protocol=0x2,0x2 layermask=0xf,0xf) I have no problem dialing out by explicitly naming the mISDN port, ex: Dial(mISND/1/${EXTEN},60) or Dial(mISDN/2/${EXTEN},60) But it does NOT work when specifying the mISDN group: exten => _(outpattern),1,Dial(mISDN/g:TEmode/${EXTEN},60)

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hi list, Hopefully, some of our Dutch members can help with this one. I'm also based in the Netherlands and am using a Sipura (Linksys) SPA-3000 (firmware v3.1.10(GWd)) as a PSTN to VoIP gateway for my Asterisk test system. It works fine, except that the Called ID (CID) is not working. I'm aware that KPN (our local telco) requires a separate subscription to activate CID on POTS

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf: