similar to: Callmanager 3.3(5) and Asterisk with ooh323

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

Hi, I am trying to communicate H323 and SIP users. I have configured h323.conf, sip.conf and ooh323.conf. If I am using gatekeeper (gnugk) then I am able to call successfully to h323 users using SJphone. And same for SIP users also. But when I disabled gatekeeper and trying to call using gateway with sjphone then every time whatever number I dial the call goes to asterisk and some computerized

anybody successfully running asterisk-callmanager scenario with h323 trunk (ooh323 channel driver in asterisk)? I'm using 1.2.12.1 & ooh323 from 1.2.4 add-ons, but seems, that ooh323 is ignoring dtmf digits from callmanager h323 trunk setup with chan_h323 is working fine with dtmf I tried all possible modes with ooh323, but without success, with chan_h323, I'm using default (rfc2833)

Hello, I can use directed call pickup using pickup application (between sip, iax, skinny cals), but unable to pickup call that is ringing on phone behind h323 gateway (using original h323 channel in asterisk), is this even suported? thx PJ exten => _*7.,1,Pickup(${EXTEN:2}) console log, when trying o pickup ringing line 324 (h323), from skinny phone (953) -- Executing

Hi, I'm trying to connect Asterisk 1.4 and Cisco CallManager 5 using SIP Trunk without MTP (media termination point). Howerver, Cisco 79xx phones do not support RFC2833, they always notify CCM5 via SKINNY channel no matter where they send RTP to. For non-MTP trunk there's Out-of-band DTMF support in CCM5 called "kpml". I wonder if Asterisk can support it. I found an

I would like to setup Asterisk for voicemail with CallManager 3.3(5). I would like to know what would be the best Distro of Linux to use and version, what version of Asterisk works best to interact with CallManager, and what H323 ChannelType works. As you probably read in another thread I tried FC5 with Asterisk 1.4 and OOH323 (included with the addons package). This doesn't seem to work to

Hi, Where can I find information on H.323 for Asterisk and/or integration with Cisco CallManager in particular? <http://www.voip-info.org/tiki-index.php?page=Asterisk+Cisco+CallManager+Integration> I have oh323 working on Asterisk. Since the CallManger I am working with is running 3.3.3 I cannot use SIP... Thanks, Adi

Some of you may remember back in May the thread on using Asterisk as a voicemail server for a Cisco Callmanager system. My own Callmanager system is integrated into an Asterisk server for voicemail (and other things). Back in May I was using H323 for integration, but since I've upgraded to CCM 4.1 I have switched over to SIP. The integration with H323 required using Call forwarding to send

Hi Users, Administrators and Pavel Jezek, You prefer chan_h323 from asterisk tree and it's of course that use channels by tree is very good. But in 1.2.x, the chan_h323 is very simple and the chan_oh323 is so bad. And I work with chan_ooh323, that it's too from Digium and work good! And I am Studing one possible change to Asterisk 1.4.x , but in 1.4.x the oh323 channel don't have more,

Hello, I have Cisco CallManager 3.3.4 and Asterisk@Home latest version. I have earlier tried getting Asterisk to register with CCM via H323 and failed. Back then, I learned that this is a known bug in Asterisk. Also people who tried doing that had also succeeded in getting calls to go through only one direction like from CCM to Asterisk. I am not that expert so excuse my ignorance with this

On Wed, 23 Jul 2003, Yifang Dai wrote: > I wish! My company just spend a lot $$ on the shinny CCM phone system, so I > don't think I can change that easily... But if I can get asterisk to > talk to CCM via h323, and prove it's usefulness, I might have a chance > to use * in the branches... Well, good luck, then! > By the way, do you know if we can get *'s VM to

Just a warning to people trying to use ooh323 with Asterisk 1.8.7. The example config file that comes with asterisk is called chan_ooh323.conf when it actually should be named ooh323.conf for it to work. Sent me into a panic when I was trying to install an H323 link to an Avaya server and the ooh323 module would not load because it could not find its configuration file. The file needs to be

I have searched and searched for over a week on this but can't seem to find the issue. Calls from CallManager to Asterisk are being disconnected immediately. I have setup CallManager and Asterisk per Shaun Ewing's pdf http://asterisk.edropbox.net/ccmasteriskvm.pdf I have installed Asterisk 1.4.0-beta3 on Fedora Core 5. I got libpri, zaptel, and asterisk compiled and installed.

hello every body, i have big problem to configure h323 trunk between cisco router and asterisk 11.13.1 which uses ooh323 module. any body knows if ooh323 module can work with cisco routers or not???? (in gateway mode, it is ok and register in cisco gatekeeper but i can not configure trunk h323) any comments or hints are really appreciated. SAM -------------- next part -------------- An HTML

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Has anyone had any luck getting a SIP trunk up and working between Callmanager and Asterisk? If so were there any steps you had to take that were not in the documentation on wiki? Blake

Hi All, I haven't started sip traces or debug yet, but was wondering what the deal is with the CCM and reinvite, why it doesn't work with Asterisk (using 1.2.9.1). I can make calls back and forth all day with canreinvite=no, when I try to reinvite an inbound sip call from the CCM with Asterisk server 1 to Asterisk Server 2, I get one-way audio issues. All the RTP ports are configured

Has anybody successfully (or I guess unsuccessfully for that matter) implemented Cisco Call Manager and used an * box for voicemail? I checked the wiki and google and I see some references to Call Manager Express and *, but CME is completely different than CM. If anybody has done this or has any insight, it would be appeciated. We are trying to migrate ~ 300 users off of Cisco Unity and

Hello! Just installed asterisk 13.2.0 and see many such messages in log, I see them in console during calls, really something like this: -- Executing [6166 at kanbaikal:2] Dial("OOH323/kanbaikal-6", "SIP/6166 at asterisk") in new stack == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Called SIP/6166 at asterisk > 0x7fa9d4007660 --

I am having a slight issue. I am trying to register 2 asterisk boxes with GNUGK and when I try to add the 2nd it gets denied cause of it saying its a duplicate. How do I change the configs to allow more than one asterisk box register to the same GK? brian This email was scanned by: Mcafee GroupShield ---------------- CONFIDENTIAL DISCLAMER ---------------- All information provided in this