similar to: echotraining=yes in misdn.conf is invalid or out of range.

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

A plea to all! Has anyone had any success with two or more avm fritz pci cards with either misdn, chan_misdn, or chan_capi, and any version of linux 2.6.x? I have managed to get misdn to load under 2.6.13 and detect two cards using misdn-capi and chan-capi (using capiinfo and capi info under asterisk) - but the second card/controller doesn't answer or dial calls. But if I try misdn

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

Hi list, I am searching for a possibility to do a certain call transfer method which is called "path replacement" in QSIG. But I want to do that in DSS1 (EuroISDN). If my asterisk does a call transfer I want the machine to signalize on dchan that the call path has to be replaced to a direct connect between the caller and the called, i.e. my machine is to hang up after the transfer and

Hi all! I'm getting an error when I try to start asterisk with chan_misdn. I patched my kernel (2.6.12.4), and compiled the whole stuff (kernel, mISDNuser, asterisk, chan_misdn). I got mISDN from http://isdn.jolly.de/download/v3.0/ I'm using a CVS Snapshot of asterisk, which was checked out about 5 hours ago. This is the error: [chan_misdn.so]Aug 15 14:13:29 WARNING[4929]:

Hi i am upgrading an asterisk server from 1.2.4 to 1.4. i've installed libpri 1.4 i've installed zaptel 1.4 I've installed the new version of misdn with the script of beronet. i use this configure script: ./configure --with-postgres=/usr/local/pgsql then: make menuselect [*] 1. cdr_csv [*] 2. cdr_custom [*] 3. cdr_manager XXX 4. cdr_odbc [*] 5. cdr_pgsql XXX 6. cdr_radius

Hi all, I've been having problems with my A20002D lately - callers from the PSTN don't hear me when I answer, but I hear them. Disabling echo cancellation in zapata.conf brings the audio (and echo) back. This used to work fine, until two days ago. The only weird thing in the logs is this: May 12 07:42:53 steerpike wan_ecd: wp1ec: The H100 slave has lost its framing on the bus! May

Hi, Has anyone had experience installing it? yum install asterisk-chan_misdn I'ts the latest Trixbox Distro version and same issues exists if add in the Trixbox repo. FAILS as per below: I have a ISDN single port PCI BRI card installed and detected. __________________ Loaded plugins: fastestmirror, kmod Loading mirror speeds from cached hostfile * addons: www.ftp.saix.net * base: