similar to: ooh323 dtmf problem

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

I have experience problems like this in a different scenario. It is usually due to codec translation problem. What is the default codec set on CCM for the IP Phone and the default set in Asterisk? Make sure the defaults are the same. Try G.711 Michael

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Hi Users, Administrators and Pavel Jezek, You prefer chan_h323 from asterisk tree and it's of course that use channels by tree is very good. But in 1.2.x, the chan_h323 is very simple and the chan_oh323 is so bad. And I work with chan_ooh323, that it's too from Digium and work good! And I am Studing one possible change to Asterisk 1.4.x , but in 1.4.x the oh323 channel don't have more,

Hi, I am trying to communicate H323 and SIP users. I have configured h323.conf, sip.conf and ooh323.conf. If I am using gatekeeper (gnugk) then I am able to call successfully to h323 users using SJphone. And same for SIP users also. But when I disabled gatekeeper and trying to call using gateway with sjphone then every time whatever number I dial the call goes to asterisk and some computerized

Dears; Actually, the needed file name to be ooh323.conf and not chan_ooh323.conf, so I copied the file from chan_ooh323.conf to a new file name ooh323.conf and it is working fine.

Just a warning to people trying to use ooh323 with Asterisk 1.8.7. The example config file that comes with asterisk is called chan_ooh323.conf when it actually should be named ooh323.conf for it to work. Sent me into a panic when I was trying to install an H323 link to an Avaya server and the ooh323 module would not load because it could not find its configuration file. The file needs to be

Dears; I am having same problem, that when I place a call from the H323 end point (even if it is not added in the ooh323.conf), then asterisk handle the call and play the wave file in the default context. Also I added endpoint to the ooh323.conf and same thing, it keep goes for default context whatever the context placed. My Asterisk vesion is 1.4.25 My Asterisk add-on version is: 1.4.8 What I

I have searched and searched for over a week on this but can't seem to find the issue. Calls from CallManager to Asterisk are being disconnected immediately. I have setup CallManager and Asterisk per Shaun Ewing's pdf http://asterisk.edropbox.net/ccmasteriskvm.pdf I have installed Asterisk 1.4.0-beta3 on Fedora Core 5. I got libpri, zaptel, and asterisk compiled and installed.

I have a Centos 5.4 64 bit installation. I've tried installing asterisk 1.6.2.7 from source, and from RPM, and although overall things work, the chan_ooh323.so module won't load. Every attempt to load causes "Capabilities failure for OOH323. OOH323 Disabled." I looked at the source and the call to ooh323c_set_capability(&gPrefs, gCapability, gDTMFMode) fails, but why

06.05.2015 10:06, s m ?????: > hello every body, > > i have big problem to configure h323 trunk between cisco router and > asterisk 11.13.1 which uses ooh323 module. any body knows if ooh323 > module can work with cisco routers or not???? (in gateway mode, it is > ok and register in cisco gatekeeper but i can not configure trunk h323) > > we use chan_ooh323 with cisco

Hello all, I have problem. I can't makel asterisk addon, asterisk-ooh323. I use Asterisk and addons svn version. OS:redhat EL4 Linux 2.6.9-5.EL #1 Wed Jan 5 19:22:18 EST 2005 i686 i686 i386 GNU/Linux Please help me . [root@asterisk asterisk-ooh323c]# make make all-am make[1]: Entering directory `/usr/local/src/asterisk-addons/asterisk-ooh323c' source='src/chan_h323.c'

Hi all. Trying to setup H.323 via Asterisk between a PLANET H.323 box and my SIP phones. When calling from the SIP phones, it connects but quickly disconnects citing the following error message: **** --- build_peer +++ build_peer +++ reload_config +++ ooh323_do_reload -- Executing Dial("SIP/yyy-2965", "OOH323/203@xxx") in new stack --- ooh323_request - data

I have posted my problem on the link below, but didn't get any answer. I am hoping someone here can help me with this issue. Here's my problem: I am using H323 to talk between Asterisk and Avaya IP Office 500. For some strange reason, when we are talking on a VoIP call, we get disconnected after 10+ minutes. We have two other Elastix box, but none of them are getting disconnected. From

Actually I am facing a problem with H.323 (the standard and the ooh323) with Asterisk vesion 1.4.25 and I discover the following: 1) Using the standard h323 that come with Asterisk: The chan_h323.so it is not existed in the /usr/lib/asterisk/modules after doing the compilation and installation for (pwlib, openh323, /chanels/h323, asterisk), although make menuselect was done and the h323 channel

has anyone managed to get these three beasties to work together ? we're using ooh323 from asterisk-addons-1.2.2, asterisk 1.2.6 and microsoft netmeeting default from windows xp. the symptoms are that calls from a SIP client to NetMeeting rings on NetMeeting, but upon answering the call in NetMeeting, no audio is passed between the two. eventually, the call times out and hangs up. on a

Call-Bilal*CLI> module load chan_ooh323.so Loaded chan_ooh323.so [Jun 17 20:23:32] NOTICE[2392]: chan_ooh323.c:2506 reload_config: Unable to load config ooh323.conf, OOH323 disabled Loaded chan_ooh323.so => (Objective Systems H323 Channel) Again, from make menuselect, if I selected chan_ooh323 from the Add-ons and I selected ADDON from module embedding. Then I ran ./configure and make. I

Hi, I'm trying to make ooh323 works with one asterisk box running 1.2.15 version. I can ring from a h.323 to SIP and SIP to H.323, but when the call is finished when the phone is answered. This is the log when I call from the H.323 device to a SIP device: Feb 23 10:57:32 VERBOSE[6096] logger.c: -- Executing Dial("OOH323/Telconet Mantaer-c5f8", "SIP/666|30|TtrwWC")

hello Dmitry thank you for your reply. Ok, you are right. i want to configure trunk h323 between asterisk 11.13.1 and 2800 cisco router. this is my scenario: PBX(100)--->cisco--->asterisk11.13.1---->PBX(200) when i call from 100 to 200, everything is ok but when i call from 200 to 100, phone rings but after i answer it, i have no voice and call terminates after 5 seconds. this is

I would like to setup Asterisk for voicemail with CallManager 3.3(5). I would like to know what would be the best Distro of Linux to use and version, what version of Asterisk works best to interact with CallManager, and what H323 ChannelType works. As you probably read in another thread I tried FC5 with Asterisk 1.4 and OOH323 (included with the addons package). This doesn't seem to work to