similar to: asterisk 1.2.12 lost phone registrations today... why?

I've had a few problems with my system holding the line after a call has been made, just now I rebooted and noticed the following in /var/log/messages Aug 13 17:23:15 Sheriff kernel: wcfxo: DAA mode is 'FCC' in the file wcfxo.c the following structure is initialised as below which would suggest that FCC is wrong for France or pretty well all of Europe. static struct fxo_mode {

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [

I've just down loaded Xten Lite and it is now build 1079. It now finds the NAT firewall type and has loads more to configure. But it doesn't work on my poor W95 tablet PC. -- Dave Cotton Directeur Linux Autrement 193 rue Marcel Cerdan 84270 Vedene 04 90 23 30 81 "Internet Sheriff Technology" revendeur en France <http://www.linuxautrement.com> IAX 17004902330

I don't think I've ever seen so many commits to the CVS, I'm not complaining. To save lots of checkout/test cycles can a message be posted when the current surge is over? -- Dave Cotton Directeur Linux Autrement 193 rue Marcel Cerdan 84270 Vedene 04 90 23 30 81 <http://www.linuxautrement.com> IAX 17004902330 FWD 42651

Hi - I'm wondering if any has experience with the Uniden UIP-200 phones. The product info says that the 8 led buttons at the top are all programmable. Can they be programmed as separate line appearances (ala Snom 200, Cisco 7960, Zultys Zip4x4, etc)? In other words - is the phone capable of multiple SIP registrations? Also, the post about these phones at voip-info.org mentions some

Hi, all. I've got my Uniden UIP200 configured via TFTP (had to get DHCP 3.0.1 -- Debian's latest is 2.0.x!), and all seems well... except for the minor detail that it doesn't work. It registers fine with Asterisk, but when I copied my Grandstream's sip.conf info and plugged in the Uniden stuff, no dice. Any ideas? Thanks... -Ken unidencom.txt: OverwriteLocalSettings

Anyone used any of the Uniden VoIP gear, any comments one how easy it was to integrate with asterisk? Also quality of the gear in general? This unit _looks_ pretty nice on paper http://www.uniden.com/productpop/00_productpop.cfm?prd_code=UIP1868 -- Harondel J. Sibble Sibble Computer Consulting Creating solutions for the small business and home computer user. help@pdscc.com (use pgp keyid

hello, yesterday the uniden uip200 phone was recommended to someone. i am looking for an alternative to grandstream bt-100 because i can not do a supervised tranfer with it. here my questions: 1) does the uip200 support supervised transfers? 2) can i buy the phones in europe, especially in germany? thanks in advance, jan goericke

I got a Uniden UIP200 and started to configure it and I am lost.... I have a tftp server setup on my * server and have the files unidencom.txt and uniden<mac>.txt there. But it doesn't quite work yet. It registers as a sip phone (sip show peers), but I cann't dial it and the display shows #1 disconnected all the time. It has firmware version BS4.59a in it. I have no idea if I

I had a working system using * 1.0 and then 1.2 and now Asterisk 1.4.13 with addons 1.4.4, zaptel 1.4.6, libpri 1.4.2. I have a mix of Grandstream (GXP2000), Uniden uip-200, Linksys Wireless G, and analog phones via Adtran chan bank. When I went to * 1.4.13, the Uniden phones stopped being able to login to voicemail. All phones are on same lan with Asterisk. I get 'Login incorrect'

Hi, I'm new to asterisk, and have a uniden UIP 200 that I got off of ebay. I'm having trouble getting the phone to register with asterisk. I've tried a few different settings. I'd be extremely grateful if someone with a similar setting could give me the sip.conf block for the UIP and the settings you're using in uniden.txt. Here's what I have currently: IP of phone

Hi, We've recently deployed 6 Uniden UIP200 phones (running firmware 4.54). We've been having some serious problems: 1) All the phones randomly reboot themselves. Typically when trying to answer or initiate a call. 2) All the phones will disconnect from a calls with the PSTN after 2-3 minutes. 3) The phones are unable to interact with a remote IVR (digit presses are not received at

Hi, I've read through the archives, and wanted to get an updated opinion on the Uniden UIP200 phone. Seems like there were a lot of opinions that it was a good phone, but there were a few items that people were waiting for firmware updates for, but that was in 2004. I'm going to be using them in an office, 12 phones, on a LAN connected to an asterisk box. Thanks for any advice or

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

Does anyone have any recent news on the Virbiage FT201 IAX Hardphone? I'd *really really* like to deploy these phones instead of SIP hardphones, and I can't help but wonder if I'm going to shoot myself in the foot (or another sensitive area) by deploying a ton of SIP phones just to find the IAX Hardphones were released a week later... Thanks, Brian D'Arcy

These are the three cheap SIP phones that I've used. Grandstream BT10x $65/street Number only LCD Zultys ZIP 2 $100/retail No LCD Uniden UIP 200 $120/retail PoE, built-in switch -- Eric Wieling * BTEL Consulting * 504-899-1387 x2111 "In a related story, the IRS has recently ruled that the cost of Windows upgrades can NOT be deducted as a gambling loss."

I'm looking for an external device that can flash when there is new voicemail in a mailbox. I'm using an SPA3000 with a Uniden 5.8 ghz wireless phone system. Problem is, the Uniden system has it's own answering machine, which I don't want to use. But the message lamps are driven solely by the internal answering machine function. Looking for something else to give a visual

Hi, all. Got my Uniden UIP200 today (ordered from thetwistergroup.com), and was very excited to set it up... until I came to the realization that there were no docs with it whatsoever. There was, however, a sheet of paper with the stock warnings (don't use the phone in the tub, etc.), AND a URL -- for documentation. Score! Well, no. The URL it gave me, bcs.uniden.com, does indeed have

Hi all, I curious to know if other UIP200 users have this same issue: You flash (XFER button) to consult-transfer a caller to another extension. If the transfer target party is unavailable (ie: voicemail), there appears to be no way to get the original caller back. If it's a known limitation, has anyone come up with a functional work around? Thank -- ..................................

Any one know of software that allows 2-way radios as VoIP(SIP) clients, besides dingotel's usb & mic cable trick ? http://www.dingotel.com/2way/requirements2way.asp They might be ok if the SIP client was not hardcode to their own SIP proxy Has anyone tried any hacks to get the 2-way radio SIP client to regsiter to a * box. hmm chan_frsgmfrs anyone? using the usb/mic cable under linux :)