similar to: Problems with hangup on TE110P and "Unexpected Channel selection 3" messages

Hello, I've got an Asterisk server with a TDM400P with 2 FXO modules and 2 FXS modules. This server is connected to 2 PSTN lines and 2 analog phones. In my Zaptel configuration, I've defined 2 groups : one for the 2 FXO's and one for the 2 FXS. The asterisk server is just used to add a little IVR and Voicemail service. Eveything works fine, but sometimes the conversation is

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

We have setup an asterisk box to let everybody call into the university internal network, but I get unexpected hangups when doing an outbound call from SIP to the ISDN interface, and it happens from 20 seconds to some minutes into the call. ----------the dial and the problem----------- -- Executing Dial("SIP/57966-a19d", "Modem/g1:96121||rt|") in new stack --

{This was posted to S-news, but not on R-help, yet. It belongs here too. I've set "Reply-To" L.Galway, as for the S-news one. Thank you very much, John Chambers! Martin Maechler, R-help list moderator } John M. Chambers Statistical Software Award Statistical Computing Section American Statistical Association The Statistical Computing Section of the American Statistical

I have a list of entrants (1-14 in this example) in a competitive event and corresponding win probabilities for each entrant. [(1, 0.049), (2, 0.129), (3, 0.043), (4, 0.013), (5, 0.015), (6, 0.040), (7, 0.066), (8, 0.038), (9, 0.204), (10, 0.022), (11, 0.234), (12, 0.044), (13, 0.068), (14, 0.035)] So, of course Sum(ps) = 1. In order to make some subsequent computations more

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

i get this message with a red signal on TE110P card: ***************** TE110P: span configured for... Calling startuo (flug is 4099) wcte1xxp: Setting yellow alarm ***************** what does mean ? thank you :)

We are in the process of installing a PRI line and we are going to connect it to an Asterisk Box. Verizon called us today to find out some information. I am surprised that they have never heard of Asterisk or Digium. But anyways, they needed some information in order to set up the circuit. Does the TE110P support NI1 or NI2? (I think the answer is both) What is the number of digits

hi eveybody, after many test with your help and the irc channels help, i get the led on TE110P green with this config: span=1,1,0,ccs,ami =====> alarms OK Green Led but the provider say that i have to set my span to this span=1,1,0,ccs,hdb3,crc4 =====> alarms: YEL/RED i can't make call's yet to test because they have to sync the Modulator in the other side so any remark? is my

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hello all, Has anyone use the Supermicro PDSME+ in combination with the TE110P successfully? My experience so far is not very good. I am running trixbox 2.0 but: 1) with zttool I am getting IRQ Misses. Don't seem to have IRQ conflict, but I am now running my SATA HD in DMA. And I am not able to set it in DMA(HIO... operation not permitted) 2) With zttool the Alarm is RED 3) When I do the

Hi, I was going to order the T100P but it is replaced by TE110P. On further reading the TE110P does not need an external router (The one that separates the data from pstn lines ?). Has anyone got it configured? And on the wiki it says that the drivers for some distros don't exist yet. Is redhat supported? And if I need to connect a fax machine will the FXO cards on ebay work (I know to

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

On Fri, 2004-12-31 at 05:30, Francisco Puentes wrote: > Hi again, and thanks (Reid) for your fast response: Glad to help. > > Yes, it works!!! Only changing the order of libraries in the Makefile. Great! > > Nowaday I have my software with the capability of compile assembly, bytecode > (from buffer and file) and link them with a set of libraries. It seems to > work

Hello every body, I ve installed Trixbox 1.2 on "DELL OPTIPLEX GX 240", i upgreded it to the latest version. I've 2 cards installed in the same pci channel via a bridge or plug i don't know exactly what's his name( but a card (1 pci) that gives 2 pci channels) the first card is TDM400P: it's ok the second is TE110P: it's not ok . No led is on neither the red nor the