similar to: Bristuff-0.3.0-PRE-1q and & florz patch compile trouble

After upgrading a CentOS 3.x box to CentOS 4.1 (both x86_64 with an Athlon64) I also wanted to get the latest bristuff. Unfortunately bristuff without florz causes the box to kernel panic within hours (console will complain about bad frame received something). It seems however that the florz patch will not work for x86_64 arch. Bristuff -0.2.0-RC8j compiles fine without the florz patch, but

Has anyone had any success using the Florz patch for zaphfc ? I have a * system with 2 HFC cards which is working fine with 2 PTP ISDN lines however the users are complaining of crackles on the line which I am assuming is related to the IRQ issues raised by Florz. I have tried to use the patch but it errors trying to patch zaphfc.h Any help would be appreciated. Regards, Stuart -- No virus

Hi, We've been using zaphfc single ISDN cards as cheap Zaptel timing sources for our Asterisk boxes for a long time, and in the asterisk 1.0.x series, had zero problems doing so. I now have some boxes with Zaptel 1.2.x (with a mixture of 1.0.x asterisk and 1.2.x asterisk), and this setup no-longer seems stable - By plugging or unplugging the ISDN cable, and sometimes just randomly the card

Hi, it helps to have configured and working kernel sources installed. Configure your kernel sources for the running kernel and then run "make" in the kernel source dir to build the necessary scripts. You dont have to wait until the kernel is compiled. best regards Klaus -- Klaus-Peter Junghanns Am Samstag, den 25.06.2005, 02:45 +0200 schrieb Stefan Gofferje: > Hi folks, > >

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Does anyone test Asterisk 1.2.X + bristuff-0.3.X and TDM card? We can't get it to work. -David -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Julian J. M. Sent: Friday, March 31, 2006 1:44 AM To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Re: BRI

I have a problem with CDR recording in Asterisk 1.2.x. This is the situation: An Asterisk 1.2.0 (BRIstuffed-0.3.0-PRE-1 with florz) machine with a single HFC-S ISDN BRI card. I log the call records to both the Master.csv and MySQL. The problem is that when an incoming call from the ISDN line is logged to the CDR, the "src" and the "clid" field show up as something like

Kapejod is working on a fix for the CDR problem in bristuff. See below ----- Forwarded message from kpj@junghanns.net ----- Resent-From: tzafrir.cohen@xorcom.com Resent-Date: Fri, 10 Feb 2006 13:01:25 +0200 Resent-Message-ID: <20060210110125.GU16880@xorcom.com> Resent-To: tzafrir@cohens.org.il Envelope-to: tzafrir.cohen@xorcom.com Delivery-date: Fri, 10 Feb 2006 05:19:50 -0500 Date: Fri,

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

Hi, I have following problems compiling bristuff-0.2.0RC8m. Has anybody seen them before and can point me in the right direction? zaphfc/make all: ---------------------- /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c: In function 'hfc_findCards': /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c:1000: error: invalid lvalue in assignment make[2]: *** [

Hello * users I've problems with sound quality on zaphfc Asterisk works fine good sound quality. If I do "make load" in the bristuf.xx zaphfc dir then sound quality drops directly. Even if I don't load the chan_zap in the modules.conf I use this config on more (even old 400Mhz machines) and works correctly. Looks like an hardware problem but I can't find it. I don't

Hi list! I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The instability is driving me crazy however. I'm having continuous problems where inbound calls will not work after some time of operation (the number then appears as not in use to the caller) or also outbound calls do not work. The solution is to unload the modules, stop asterisk, re-load the modules and

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

Hi, I'am having some problems with new mainboards and 3xHFC-S cards. The the first problem was with interrupts, I mean if HFC-S card was using interrupt i.e. 21 or higher - it didn't work. Solved by disabling APIC. However, still the driver behaves a little bit strange. If card 0 & 1 is TE and 2 is NT, TE works fine, but NT is not working at all. If card 0 is NT and 1 & 2 TE - all

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

I applied the florz patch but my problems remain. Now I get all sorts of weird errors on the console and I cannot make outgoing calls. Incoming calls work as expected. I am using a single HFC-S card with BRI. Any clue what these errors below are? Ri = 44651 TEI msg = 3 TEI = 7f Ri = 3800 TEI msg = 3 TEI = 7f Ri = 42399 TEI msg = 3 TEI = 7f Ri = 42409 TEI msg = 3 TEI = 7f Ri = 22078 TEI msg = 3

I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make

Hi all! Was anybody able to install kapejod's zaphfc drivers together with RealTime application? I'm in big trouble because bristuff relay on STABLE version, while RealTime is included in the CVS-HEAD. I found this hint, "Installing zaphfc with CVS-Head" at http://voip-info.org/wiki-Asterisk+zaphfc+install, but it was written many months ago: may it be still useful? TIA, Alex

Caller id is not in the configs that are supplied with zaphfc from bristuff, and it's not mentioned in the wiki. Is it possible to use callerid with zaphfc/bristuff? Thanks!!