similar to: ISDN BRI NetJet

Displaying 20 results from an estimated 2000 matches similar to: "ISDN BRI NetJet"

2007 Mar 22
1
Problem in using Two BRi Cards in Asterisk
Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg
2004 May 23
3
NetJet and RAS
Hi, Last weekend I was planning to buy a physical PBX system, but instead I have been blown away by the fact that VoIP really works, that Asterisk is so easy to set up and use... and free! We're in Australia, so as I understand it, we aren't allowed to use the Zaptel cards. We need to set up our system to route incoming 56K data calls to the PPP daemon on our Linux box or to our
2003 Nov 01
1
NetJet Cards
Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing
2003 Sep 02
9
ISDN
Hi, I am using a Netjet-s ISDN Card, and am having some trouble dialling out (Incoming Works Fine). TRUNK=Modem/ttyI0 exten => _90XXXXXXXXX,1,Dial(${TRUNK}/${EXTEN:1}||Ttm) exten => _90XXXXXXXXX,2,Congestion I get the following when diallingout: -- Starting simple switch on 'Zap/2-1' -- Executing Dial("Zap/2-1", "Modem/ttyI0/04XXXXXXXX||Ttm") in new
2004 Sep 07
1
Asterisk + NetJet (ISDN4Linux)
Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y
2004 Jun 07
1
isdn4linux, NETjet, chan_modem help needed
I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing
2005 Feb 15
1
Teles PCI and chan_capi, possible ???
Hello! I'm curently using * with two old Teles PCI card (wich, btw, were hard to install and make good use of) with ISDN4Linux. The sound quality is simply perfect. However both dialing in and out through the ISDN line, there seems to be a _little_ bit of echo that eventually gets on your nerves ! Also the echo seems to get a _little_ bigger after a minute or so into the conversation. Now,
2014 Jan 27
1
AsteriskNOW with AX1600P card
Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac
2005 Aug 20
1
ISDN BRI voice one way only
hi PSTN <--> [Teles ISDN / Asterisk] <--> SIP client When call is made through ISDN, no matter if taken from PSTN or Asterisk side, person in PSTN side can hear perfectly but in Asterisk side I only hear a very scrambled or very low quality voice, words repeated several times. Same is with echo test (call taken from PSTN) Setup: * Teles 16.3 ISA ISDN card with hisax kernel module *
2004 Sep 18
1
NEWBIE - No Audio on ISDN BRI (Teles PCI)
Hello, folks! This is my first post here. I installed Asterisk from scratch and after reading a lot of information on voip-info and this mailing list I was able to get started. I can make sip-to-sip calls (just on a basic extentions structure, let's say for beginners) but now I'm trying to make this system works with my Teles ISDN BRI PCI card. I can make and receive calls through X-Ten
2004 Sep 22
1
(euro)ISDN: complete silence / can't hear a word.
Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network
2011 Jun 01
1
Dahdi_genconfig - "Empty configuration -- no spans"
Asterisk - 1.8.4.1 Dahdi-linux - 2.4.1.2 Dahdi-tools - 2.4.1 Kernel: 2.6.37.6 Kernel BKL: enabled I am upgrading Asterisk on this box. It has an OpenVox A400P PCI analog card with 1 FXO and 1FXS module. This server has been running just fine for two years with Asterisk 1.6.1.0 I've just upgraded all the OS and installed Asterisk 1.8.4.1. On trying to configure the A400P I get: # modprobe
2003 Sep 02
4
DTMF Tones During Call
Hi, I am receiving calls via a Netjet-S card on asterisk, and I notice that whenever I am talkimng to someone, if their voice is loud enough, sometimes asterisk generates a DTMF Tone as they speak. that is played to me. (Caller doesn't hear it). Any ideas how to stop this?
2012 Jun 21
2
Asterisk 10/1.6.1 and Dahdi/Libpri compatilities in BRI /PtmP
Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are
2007 Mar 24
1
Issue with Hamlet ISDN PCI card(Cologne Chipset)
Hi everybody I have installed a TrixBox with Asterisk 1.2.14 and relative upgreaded software. I Bristuffed it with last version of bristuff to use a Hemlet PCI ISDN CARD in a normal Italian EUROISDN installation. The * works fine except for the ISDN CARD. It is always Channel D down, but if a Call comes in, it works perfectly for some time, both inbound and outbound. It prompts Channel D UP!
2006 Jan 17
3
Fritz card technology & German *
Hi all, I've been working with * for a long time now, but only with analog FXS/FXO systems. I am venturing towards setting up a box in Germany now and I believe that requires a Fritz card? Do I even have to use the Fritz cards? Why not a Digium card.... We have 2 ISDN lines ( --> 6 handsets) so I'm guessing that will require 2 Fritz PCI cards (they have 1 port only). Then
2006 Mar 03
10
MultiBRI in Australia - found one - maybe
I may have found a source of an A-Ticked HFC 4BRI PCI adapter in Australia, and will be testing one next week if all goes well. I don't want to post the details of the reseller online unless invited to do so, so if nobody replies and says they are interested then I won't :) I'll follow up once I've tested it. Let me know if you want the details. James
2004 Sep 13
4
PABX & VOIP Gateway
Hello, I'm researching the possibility of using VOIP (SIP) with an existing PABX system. Ideally, the setup would be to dial an outside line through the PABX (that would actually link to the the VOIP gateway). At this point I would prefer not to purchase a hardware-based VOIP gateway. I would prefer to use a software-based gateway for research & testing purposes. Could anyone please
2006 Jan 31
1
Leftover sound on isdn modem channel
Hi, I have a strange problem on some isdn modem channels. (* 1.0.9 / chan_modem / 2xHFC-S cards). Everything works fine but when the 2nd (and 3rd etc..) call comes in and * answers and there is about a 1/2 second of sound from the previous call (ivr) before the sound from the new call is heard. It just sounds bad and is quite annoying. I am assuming this is sound that is still in a buffer
2006 Mar 29
1
zaphfc on an 'actual' asterisk?
Hi all I don't manage to get asterisk 1.2.5 or 1.2.6 running with the zaphfc driver.... The scripts from junghanns.net do download a very old libpri and asterisk version which is too buggy for me to use. Isn't there an acutal patch to get zaphfc support in *? -Benoit-