similar to: No CID on ZAP

Hi people, I have the following dialplan, but it doesn't have the behavior that I think it should have. [default] exten => 2001,1,Answer exten => 2001,n,Dial(local/3005) exten => 2001,n,Hangup exten => 3005,1,Set(__RINGTIMER=10) exten => 3005,n,Macro(exten-vm,novm,3005) exten => 3005,n,Hangup When I execute the Originate (AMI) with the argument Channel=local/2001, It rings

I have Asterisk 1.2.29, Zaptel 1.2.24 and Freepbx Setup for a queue up to 15 agents through a PRI line, it was working fine for more than 1 year, suddenly, when there is a load on the queue, the asterisk service disconnects and the calls are dropped. And the service starts again after few seconds, and so on. I am not using fax. I checked PRI by zttool and there are no alarms. The cdr logs

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

Hi, I set up a ring group. I would like for people who select a certain voice menu option to ring a list of extensions (I have just one extension in there at the moment) and if it doesn't answer to go to an extension's voice mail. I am using a version of asterisk from CVS, last updated a couple of weeks ago. This line in extensions_addtional.conf sends the call to ringgroup 3 if

Ive installed asterisk and freepbx. Through the interface ive configured 2 extensions, 6000 and 6001. My problem is that when i try to call from extension 6000 to 6001, i hear this msg "Im-sorry&an-error-has-occured" and the call is terminated. As expected if i call to another number i get an error. i thought the problem might been related with the NAT but if checked and changed some

Hi, i got Ubuntu 6.06 installed and theres a problem with asterisk. I've sucessfully installed it with the command: #apt-get install asterisk Then after installing FreePBX i get this error when restarting asterisk: root@hernandezz-laptop:/home/hernandezz# asterisk -rvvvvvvvvvv Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?) After looking at the logs i

Hi Everyone, I have an asterisk box in my office. It does not display the correct Incomming Caller id. For incomming we are using ISDN Bri line which is terminated in a Digium 4 port bri card (B410P). Like if a number say 02 12345678 calls to our line asterisk displays it 12 12345678. Similarlay if a mobile number say 0416 123456 dials us , asterisk displays 1416 123456. I am not sure where the

Hi, Hi All, I've just delved into the world of asterisk and I'm having a few dtmf issues. Internally, amongst sip phones, dtmf is fine. Externally, if you ring from a GSM mobile, DTMF is fine, however if you ring from a standard phone, DTMF fails to register. I am attempting to use a quad port HFC-4S Beronet Card. I've been searching the web most of the last week and

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

I have call center PCs that switch between an IBEAM SIP softphone and a NEBU IAX softphone (for reasons that aren't germane here). The SIP softphones work fine, but the IAX softphones get a fast busy unless I give them an IAX trunk to use, instead of the PRI trunks that all the other phones are using. I am using Asterisk 1.2.3. svn rev 47264. I've appended a sample call trace. The

Hello, i've recently switched over from 1.0.9 to 1.2.3. I've experienced some (to me) weird behaviour. This is the config for an example queue.conf: [654] wrapuptime=30 timeout=20 strategy=ringall retry=5 queue-youarenext=queue-youarenext queue-thereare=queue-thereare queue-thankyou=queue-thankyou queue-callswaiting=queue-callswaiting music=default monitor-join=yes monitor-format=

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as

Have asterisk@home 1.2.1 The server is on an internal network eg 10.10.10.10 It is NAT'd 1:1 via Checkpoint firewall to external public IP eg 50.50.50.50 The remote IAX2 phone (ATCOM320) is configured to call 50.50.50.50 on extension 1055. Outbound calls to 1055 work perfectly. Inbound calls from 1055 get picked up as if it were an external call (see below) and goes straight to the ring

Hi, i have a HT 488 and I want using this like an FXO for Asterisk. I have find some configuration in the list archive & google but my HT with these config not work. my sip.conf [HT-488] username=400 type=peer secret=wowowow qualify=yes port=5062 nat=no host=192.168.1.157 fromuser=400 disallow=all context=from-pstn allow=g711u allow=ulaw allow=alaw my sip debug:

I'm using FreePBX 2.5.2.2 with Asterisk 1.6.1.4. If I make a call and then decide to blind transfer them using ## my side of the call is not hung up. Instead it sends me to voicemail. If somebody calls me and then I blind transfer them with ## I am hung up on as expected. I called from 8678 to 28688. I then transferred the call to 8532. Asterisk acts like it wants to hang up, but then

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

hi,all when i send a call to other server use SIP trunk, i got this below, <--- SIP read from 222.46.18.52:5060 ---> SIP/2.0 403 Forbidden what's rong with is? > Asterisk 1.4.21.2, Copyright (C) 1999 - 2008 Digium, Inc. and others. > Created by Mark Spencer <markster at digium.com> > Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for

Hi, maybe a dumb question, but it seems that some calls are directed to our central dial in number despite the extensions the callers say they dialled. E.g. they dial 1234-567, asterisk recognizes 12345, it says this is an unknown extension, where it is right, and redirects the call to the central dial in extension 1234-0. This only seems to happen when the numbers are dialled manually. When

Hello List, I am having a strange issue with a trixbox system we installed for a client, and I would appreciate any help on this one. The issue is that occasionally when they go to answer an inbound call from the Sangoma A200 - there is no one there, and they are presented with dial tone. The calling party is hung up. A bit of background: The client actually has two systems install (one at