similar to: chan-capi and dtmf

Hi Yair, Please let me if you managed to fix the DTMF tone issue, which you were experiencing couple of months ago. If not can you share any advancement. I'm currently experiencing the same issue, I can make outbound calls but DTMF will not work when dialing IVRs. My configuration is asterisk@home 1.5, registering to Voip provider (Symbio), codec is g.729 and dtmf mode is set to rfc2833.

Helo List, Sorry I missed the rest of my email in my previous post. Please see below. I'm having an issue using the AND (&) operator evaluation in the code of my dialplan. The dial plan is coded to detect inbound DTMF digits from callers. key "1" is equivalent to "yes" and key "2" is equivalent to "no" in two diferent contexts in the dial plan.

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hi all, I compiled/installed chan_capi.so without problems. When I launch Asterisk, I get the following error: --- [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Mar 30 19:47:52 NOTICE[16384]: chan_capi.c:2338 mkif: ast_capi_pvt(91xxxxxx,*,pstn,0x2,2) (1,2,64) (0)(0.800000/0.800000) 0 Mar 30 19:47:52 NOTICE[16384]: chan_capi.c:2338

Hi Can someone please help with the following, We are using asterisk@home 1.5 and SIP trunks to communicate to the PSTN network. We are having some problems with the call quality. Although we can hear the other person's voice quite clear when making or receiving a call, we get complaints from the people on the other end saying that our voices sound very unclear, low and that the voice

Hi! I have installed two hfc-s cards to handle my pstn calls. I use mISDN with capi, so capi.conf is edited. I have tested both separate and cards are working well. But they are not working together. It seems that when i set up settings for the other card: ;capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=50 incomingmsn=* controller=1

Hi List, I am experiencing an issue in a server that I have installed asterisk; configured an AVM FRITZ card to work with the capi module. Once istalled the card works perfect; however every time I reboot the machine I found that I have to re install the capi4k-utils before I can load asterisk otherwise the capi module will not loadup. Can anyone direct me in the right direction in order to

Hello, AFAIK the feature CD (call deflection) is only possible on point-to-multipoint links, is this correct? I've heard about the feature "partial rerouting" which should do the same on point-to-point-links. Is this implemented in either bristuff or chan-capi(-cm)? Thanks in advance, Karsten

Hello asterisk-users, I recently set up an asterisk server using Debian Sarge. I also added an ISDN card (AVM FritzCard PCI) to the machine. I built amd installed a new kernel (2.6.15.1) with modular support for the CAPI stuff and also integrated the FritzCard driver available from AVM. capiinfo succeeds in correctly showing the ISDN card. When talking from one PC to another via SIP, everything

Hello all, I've just finished to install chan_capi with 3 AVM Fritz PCI cards. It correctly loads the 3 drivers, and * starts without errors. immediately after * start, audio quality is really fine, but, after the first incoming call, all incoming audio is broken, trembling and stuttering.

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi, I'm having a problem with DTMF tones from my SIP client apparently crashing the chan_capi driver. However I'm not sure whether this is a bug or misconfiguration on my part: if I set "softdtmf=1" in /etc/asterisk/capi.conf the problem goes away. Does the AVM B1 not support DTMF detection? The set up I have is using latest CVS (3 days old) running RH8 on a 933MHz P3. SIP

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi, I have a set of data in x,y coordinates across the range of -5 to 5 in each dimension. I would like to obtain the frequency distribution of the different points, and then graph them so you can see which of the points are the most frequently occurring. This would seem to be easy in Matlab, which has the hist3 command for doing frequency distributions/histograms in 3 dimensions. However,

Hi all, I am trying to get Capi Dial to use a specific outgoing msn. I can't get it to work. If I make a test call to 0703241494 (same isdn line, just one of the other numbers) I don't get CLID at all. Any ideas? ; use 0703241432 as outgoing msn exten => _070.,1,Dial(CAPI/@0703241432:${EXTEN}|30|r) in capi.conf I have: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8

Hi everyone, I have got some questions about Speex, I am sorry if my questions are too newbie: 1. For the LP analysis, did Speex use the AR (Autoregressive) model or the ARMA model? 2. Am I right to say that Speex use a multistage VQ (since I believe Speex employs two or more VQ consecutively - based on the manual it says that Speex uses dynamically selectable codebooks (linear

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

I use AVM fritz card A1, I have install with instruction of Voip-info.or, but it don' work. capiinfo Number of Controllers : 1 Controller 1: Manufacturer: AVM GmbH CAPI Version: 2.0 Manufacturer Version: 3.101-02 (49.18) Serial Number: 1000001 BChannels: 2 Global Options: 0x00000039 internal controller supported DTMF supported Supplementary Services supported channel allocation