similar to: MWI on the PA168V in IAX mode?

For those of you who may be interest.... IAX2 loads are now available for the standard builds... http://www.aredfox.com/edownloadsiax2.htm Just a word of caution... Remember to change the ports over to 4569 from whatever. And don't forget to grab the palmtool from http://www.aredfox.com/download/tools/PalmTool.zip My own testing of IAX2 with both a phone and an ATA is that IAX2 is

do you have selinux enabled? It should not be. p p.s. - if it comes to re-installing, you can backup all your settings with the freepbx backup utility and then restore so that you don't have to re-enter everything. From: "Lachek Butalek" <lachek@gmail.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Date:

My mission is to get one * box to dial another * box' extensions. I have set this up previously without any issues by making a simple IAX trunk/extension pair on the two boxes and create a dial plan with a prefix like 9|XXX to select an extension on the other box. My problem is that I now have to do this with extremely restrictive firewalls thrown into the mix - firewalls I have no control

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

Situation, simple home setup: * Trixbox 2.0 * Feature Codes installed * GNet PA-168V based ATA * Cheesy cordless analogue phone >From what I gather, dialing *70 from the handset should activate Call Waiting. All it seems to do is change the message "The person at <extension> is on the phone" to "<ring> <ring> The person at <extension> is

Figuring I knew what I was doing (I didn't - surprise) I added a totally unnecessary line in /etc/asterisk/extensions_additional.conf a couple of days ago. Troubleshooting a dialing rule issue, I'm now realizing that FreePBX is updating its database with the new settings but is not rewriting/updating extensions_additional.conf with the changes I'm making. I've tried renaming the

I'm looking for an ATA\Voice Gateway that runs IAX and has several ports (8 would be nice). I am looking to avoid devices that use the same firmware as the ATCOM devices as I found them to be buggy (and a PITA to find the proper update). ---------- Mike Hammett Intelligent Computing Solutions http://www.ics-il.com -------------- next part -------------- An HTML attachment was scrubbed...

can someone overthere help? the server specs are as follows HP DL380G4 Dual Intel Xeon 3.2GHz processor with 4GB RAM, running fedora core 3 asterisk-1.2.5 ss7-0.8.3d. using sip as advised to receive calls from another gateway in US. using g729 in transcoding way. however, I noticed the call hit the 51 active calls which is 102channels, I run "top" to check the system resources usage

I known. I'm using the 1.44 firmware version relesed on 26 may. I worked for italian IVR an HTTP pgaes. So i can only update asterisk with CVS and try atxfer. Thanks for all -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Gavin Hamill Inviato: luned? 30 maggio 2005 18.40 A:

Hi, guys. May be someone could give me advise? I am trying to find good VOIP provider ONLY for OUTGOING calls with low per channel cost and cheap rates on Eastern Europe, Turky and xUSSR. Should support g729 or g723 codecs, SIP or IAX connectivity. -- ========================================================================= = Best regards, Nikolay Pavlov.

I purchased an IAX2 hardphone, X100 otherwise known as a Netweb X100 or YWH100 with a PA168 chip and the latest firmware 1.45 available, from a US retailer. I was able to configure the phone to work with my Asterisk box, except the hold and transfer buttons do not work. When you press the hold button, it rings endlessly, the transfer button, displays "transferring" but it does nothing.

Hello I'm thinking of selling an Asterisk server based on Atcom's IP02 solid-state unit with one FXO and one FXS ports: http://atcom.cn/En_products_IP02.htm By default, this unit based on a 400MHz Blackfin 532 chip only has 64MB RAM and 256MB of NAND flash. Those can be increased to 128MB and 1GB, respectively. Do you think I can install Linux + Asterisk + LAMP (replacing MySQL with

The procedure that will do asterisk is very nice ;) but whe it was available ? Currently is there any way to emprove the transfer? I tryied the scenario that u suggest me but it doesn't work :| and i don't why. Here my sip.conf for the phone, can u say me if there is somethingh wrong ? [2391] type=friend username=2391 secret=2391 language=it host=dynamic context=intern dtmfmode=rfc2833

Hi, i need an recommandation for an ATA adapter to use with an anlog fax maschine. I would appreciate any hints. Regards!

Hello According to this article, this nice little unit can only use the PSTN port for outgoing calls (ie. as a backup in case the connection to the VoIP provider stops working), but not incoming calls: http://tinyurl.com/mwjmo8 Can someone confirm that Atcom made this strange decision, and that there's no work-around? Thank you.

Anyone here used these phones? I'm getting more and more frustrated by todays modern crop of routers with their so-called SIP ALGs which are invariably broken, or routers with built-in ATAs which block internal SIP phones from working, so looking to use IAX for some end-users. I already support it for people who want to use (eg) Zoiper and use IAX a lot to plumb boxes together, but never

Hello For customers who need a small IP PBX to handle up to four ISDN lines (in France, so I guess that means EuroISDN) instead of a PC + Asterisk and an ISDN gateway box, has someone already played with the Atcom IP-4B? www.atcom.cn/IP-BRIM.html Any feedback appreciated.

Hello All We purchased *25* new AtCom AT- 530 phones. Four of them did not work for even once and some of them lost configuration after some days. I talked to AT Com people over chat for support. They have just 1-2 people for support who are also busy in some other activities due to which they are unable to communicate in proper way. Often support guy left conversation suddenly and is unavailable

Does anyone know why when calling out with an ATCOM AG-188 registered with IAX (haven't tried SIP), there is no ring. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070222/a4f29a97/attachment.htm

Hi all. We have Snom phones which do have a defined key in order to drop incoming call WITHOUT answering. Pressing that key, a "SIP/2.0 486 Busy Here" message is sent back. We have other phones (I.E. DECT Siemens C450IP, or ATCOM 320 or other) which DO NOT have any key to do that (or the key does not work, as is with Siemens C450 IP ): you have to answer and immediatly after hangup the