Displaying 20 results from an estimated 2000 matches similar to: "R2/MFC Configuration."
2006 May 24
2
TE406P - MFC/R2
Guys,
I'm trying to configure a TE406P with MFC/R2.
here goes my zaptel.conf:
span=1,0,0,ccs,hdb3,crc4
cas=1-15:1101
dchan=16
cas=17-31:1101
span=2,0,0,ccs,hdb3,crc4
cas=32-46:1101
dchan=47
cas=48-62:1101
The first strange behavior is that the:
zap show status
shows this:
Description Alarms IRQ
bpviol CRC4
T4XXP (PCI) Card 0 Span 1
2006 May 17
3
Slackware 10.2
Hi guys, I'm trying to use asterisk with my slackware 10.2 box.
Kernel 2.6.13 from the testing...
The udevd are not creating the /dev/zap devices.
Someone already have success installing asterisk over slackware?
Thanks in advance.
Fernando Lujan
2006 Mar 29
5
Asterisk Between PBX and FXS
Hi guys,
I''m setting up asterisk to run with another pbx server. This pbx server
support a feature that allows 2 extensions connect to the same FXS. No I put
asterisk in the middle.
Asterisk receives the call and dial to a SIP/peer.
How the pbx installed support 2 extensions to one fxs... How can I figure out
in asterisk which extension was dialed before the call came to asterisk?
2007 Jan 08
1
MFC/R2 problems
Hi all,
I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled, and a Sangoma A101, and when I
make a call I get this:
Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception: Exception on 19, channel 1
Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101
[1/ 40/Seize /Idle ]
Jan 8 13:04:06 WARNING[12252]:
2003 Sep 11
1
Is there any MFC-R2 implementation for asterisk?
The last thing that I read about it was:
Steve Underwood [steveu@coppice.org] wrote on Sep 3:
>> Is E&M designed to work with the E1 driver code? I think probably not. I
>> had to fix some things to get proper access to the CAS signaling bits
>> when I implemented MFC/R2...
So, apparently he implemented it.
I was trying to contact Steve, but he isn't answering me.
Does
2010 Nov 10
1
MFC/R2 detected as ISDN PRI
Hi list,
I'm trying to setup an asterisk 1.8.0 with MFC/R2, but I'm having these
error messages loading chan_dahdi:
> module load chan_dahdi.so
ERROR[9241]: chan_dahdi.c:11848 mkintf: Signalling requested on channel
1 is MFC/R2 but line is in ISDN PRI signalling
ERROR[9241]: chan_dahdi.c:16180 build_channels: Unable to register
channel '1-15'
I got the config in
2007 Jun 14
2
Unicall + MFC/R2 line dropped immediately after connect
Hi,
I am trying to set up an E1 line with CAS signaling using available
unicall patches with libmfcr2 implementation. Inbound calls works well,
I am able to get DNIS and ANI from incoming call, but I am still not
able to make an outbound call with our local carrier.
After tweaking of protocolvariant parameter in unicall.conf I was able
to find proper values for inbound and outbound calls, but
2006 Oct 11
6
Asterisk + E1 with MFC/R2 in Argentina?
Hello,
Has somebody installed this configuration: Asterisk + E1 with MFC/R2
(Telef?nica Argentina) in Argentina before? I need to know if it?s
possible with MFC/R2 argentine variation.
Thanks in advance.
R.R. Libera
2006 Dec 13
1
MFC/R2 on chan_zap
Hello.
I'm trying to setup MFC/R2 signaling, but chan_unicall fails at loading
with this message:
---
Unable to load module chan_unicall.so
Loaded /usr/lib/asterisk/modules/chan_unicall.so => (Unified call
processing (UniCall))
== Parsing '/etc/asterisk/unicall.conf': Found
061213-075938 ERROR[11454]: chan_unicall.c:3361 mkintf: Unable to open
channel 1: Success
here = 0,
2006 May 02
1
Unicall MFC/R2 B3,B4 and clear back
Hi All,
I have an R2 installation still undergoing testings, during the test I notice that the Unicall
always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the
dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a
Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or
2007 Aug 13
1
Does digium TE120P card support for MFC/R2 protocol
Hi,
I have successfully configured DIGIUM card and successfully communicated
through it to the another E1 card running application. Can anybody tell me
does TE120P
support MFC/R2 protocol.
Thanks and Regards
sanchal singh
2005 Sep 08
1
can not make call with Unicall (MFC/R2)
Hi,
?
I run the program testcall with one E1, it works fine; I receive DNIS and
ANI for making calls and answering calls.
?
When I start the Asterisk I receive call from outside correctly including
DNIS and ANI, and receive the following messages:
?
Sep? 7 10:29:59 WARNING[12167]: Answer Call
Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5)
Sep? 7 10:29:59 WARNING[12167]: MFC/R2
2004 Oct 04
2
RES: Working E1 MFC/R2 M?xico !!!
Miguel,
How many simultaneous calls (incoming and outgoing) you did ?
Kind regards,
Miguel
Date: Sun, 3 Oct 2004 11:21:04 -0500
From: Miguel Cavazos <miguel@cavazos.com.mx>
Subject: [Asterisk-Users] Working E1 MFC/R2 M?xico !!!
To: Asterisk Users Mailing List - Non-Commercial Discussion
<asterisk-users@lists.digium.com>
Message-ID:
2005 Sep 29
3
Problems using SIPURA and MFC/R2
We are using MFC/R2 driver successfully in at least three places in Brazil. I have problem with an Asterisk integrated with MFC/R2 with a Siemens Hicom 300. I can get a good audio quality with Grandstream, Polycom, and X-Lite softfones, but SIPURAS and Linksys get a garbled audio, something like a "Darth Vader" voice. We have tried everything in Sipura. The SIPURA 2000 and the Linksys
2004 Oct 05
2
Re: RES: Working E1 MFC/R2 M?xico !!! (Steve Underwood)
Steve,
Do you know if there are many differences between the Mexican and Brazilian
variant ?
Kind regards,
Miguel Antonio
Date: Tue, 05 Oct 2004 22:51:53 +0800
From: Steve Underwood <steveu@coppice.org>
Subject: Re: [Asterisk-Users] RES: Working E1 MFC/R2 M?xico !!!
To: Asterisk Users Mailing List - Non-Commercial Discussion
<asterisk-users@lists.digium.com>
Message-ID:
2008 Jan 11
1
Fwd: Trying to build MFC/R2
---------- Forwarded message ----------
From: Brian Hutchinson <b.hutchman at gmail.com>
Date: Fri, 11 Jan 2008 12:22:09 -0500
Subject: Trying to build MFC/R2
Hi Moy,
I downloaded your astunical-1.4.16 and have been studying it.
I have a machine running the latest download of asterisk-1.4-17 and was
trying to figure out how to build MFC/R2 support into it.
I merged your unicall specific
2005 Aug 23
5
chan_unical-MFC/R2 CPU usage problem
Hi All,
I have installed chan_unicall and MFC/R2 successfully, and is runnign fine.
But I noticed that once unicall is installed, asterisk CPU usage as reported by 'top', jumps to 99% every few seconds.
I have no incoming calls, and I have even removed the E1 lines from card and I tried almost everything possible but I was not successful in determining the cause of this high cpu
2007 Aug 17
1
Problem in installing libmfcr2 for configuring MFC/R2
Hi,
I am trying to configure for MFC/R2 for asterisk. With the help of one
of the asterisk users group
member patrick I am able to install libunicall library. Now, when trying to
install libmfr2-0.0.3 it is giving error.
On running running command $./configure
It is giving error -> can't build without libtiff
I downloaded tiff-3.8.2 and installed the libraries but still
2005 Aug 03
2
MFC/R2 Mexico Unicall Blocked
I've been trying to configure an E1 in Mexico using unicall, i went
into vozdigital, googled this list, and finally followed this
instructions:
http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2
I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10
"channels" assigned from my telco.
However when i try to simulate a call using this call file:
--------call
2004 Sep 23
10
MFC/R2
Hi all,
I have begun the release of my MFC/R2 protocol software. At
http://www.opencall.org/installing-mfcr2.html there are instructions for
installing what I have released so far. This is the MFC/R2 protocol
software, and a test program. The software to interface Asterisk to the
MFC/R2 code will be released shortly. It used to work, but it hasn't
been touched for a while, and Asterisk