similar to: Audio problems 50% of the time.

Hi everyone, I'm trying to send a FAX with the following configuration: Analog FAX machine (OKI) <----->SPA21000<----->LAN<----->Asterisk<--------> PSTN I'm restricted to use passthru mode for faxing, instead of T.38 protocol, because the Asterisk box is running v1.2 and cannot be changed as it is in a heavy production environment. Anyway, it "should"

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

I've got a Sipura SPA-1001 that I'm trying to get working with an Asterisk server that's on the public Internet, while the SPA-1001 is behind NAT. I did the first obvious thing and mapped ports 5060 and 10000 - 30000 to the local IP address of the SPA-1001. Tried numerous proxy settings, have all the NAT settings == yes. Registration seems to be happening; with sip debug on, I see

I have a Uniden wireless phone connected into Linksys/Supura 2100. It works well, except I never see any caller ID information displayed on the phone. Is that a setting in the 2100 that I'm missing, or is it an Asterisk setting or isn't it possible? Thanks, Jim.

Upon setting up and configuring the my extension.conf, meetme.conf and following the instruction outlined at this web page: http://www.voip-info.org/wiki-Asterisk+timer+ztdummy I get the following errors when calling the meetme number. Executing Wait("SIP/216.53.118.2-f41196e0", "1") in new stack -- Executing MeetMe("SIP/216.53.118.2-f41196e0",

I have two * boxes running two differnet versions of *. Box A is running: Asterisk CVS-HEAD-07/14/04-16:28:29 built by root@asterick.dell.cpu.com on a i686 running Linux Box B is running: Asterisk 1.0.3 built by root@dell.cpu.net on a i386 running FreeBSD I can make a IAX call from B to A but not from A to B. When I try to make a call from A to B I get these messages: Feb 21 12:48:12

Ok, I've done some more research and I don't think I want an FXO box... What I'd like to do is use BroadVoice (with their BYOD plan) and then run Asterisk on my WRT54G router. I'd also like to use my regular home phones without having to use a special "SIP" phone... (eg. I like my Vtech normal cordless phones) What do I need to buy to get this working? It sounds like I

I have an ATA186, a tech just told me to set UID0 and UID1 to the same username, and PASS0 and PASS1 to the same password. In my mind, this would seem to have the unit registering twice under the same account, which Asterisk wouldn't support. When a call comes in, it should go to the last line to register. So to me, this means the call could sometimes come in on Line 1 and sometimes on Line

I have two ATA186 running 2.14 and 2.15. I see in the SIP debugs that both ATAs keep on sending SIP registration packets over and over. The flow is as follows: Asterisk receives REGISTER packet Asterisk sends 100 trying, 200 ok with an expire of 3600. Kurt __________________________________ Do you Yahoo!? Yahoo! Finance Tax Center - File online. File on time.

I noticed when I call certain IVR systems, such as 1800calldhl, that Asterisk will not barge the prompt. Would this imply that Asterisk has an Early media detection problem. Is anyone else experiencing this problem. Is there a fix? Kurt

Hello Everyone - Well, I think I'm getting closer with the asterisk connection. This is my setup and I keep getting this error below in ,my /var/log/asterisk/messages file. I have opened 5060 port on the firewall box. I would this is Warning which I can ignore! But I see the connetcion coming but NO DIAL TONE on mt ata186 box sitting in my 192.168.200.x site! I'm using ATA186(cisco

Hi there, We have plans to install an office (not call center) with the following setup: 200 linksys 942 phones (sip + g711) on a LAN a server with a dual port E1 sangoma and a remora card with 4 fxo modules. So far when we want to setup a linksys phone, we need to use the http interface of each phone, disable/enable a lot of things and plug it into the network. this is not the best scenario for

Hello-- In the interest of Symmetry, does anyone else in the world see any need for a device like the IAXy (or the SIP ones from other manufacturers, like the ATA186), but one that presents an FXO interface instead, so it can be connected not to phones, but the PSTN? murf

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

I'm having a horrible experience getting a Cisco ATA-186 to work with *. I can make calls from the ATA with no problems. However, incoming calls make the ATA ring once, and then the call is disconnected. I have no problems with my Sipura 2000 or my Grandstream phones. I am running 2.16.1 sip code on the ATA 186. Neither * nor the ATA is behind a NAT. They are both on public IP addresses

Hi guys, Having a bit of a problem trying to get conference bridges working. In my meetme.conf file I have the following line [rooms] conf => 6000 In my extensions.conf file I have: exten => 1000,1,MeetMe,6000 My problem is that when I dial into extension 1000 it is telling me "this is not a valid conference number". Can anybody telling me what I'm doing wrong here?

Hi all, I have around 100 SPA2100 registered in my provider openSER. I'd like to add an Asterisk registered into openSER, to the network, to deploy voicemail service for those SPAs. Due to administration access levels, I have no access to SER box, so I'm wondering if that possible: - Some foreign user (say A) calls one of my SPA (say B). - B don't answer. So.. B SPA is setted up to

Hey Everyone, I am playing around with my * box, and I have a few different phones hanging off it it right now. I have a Cisco 7960 capable of g729, ulaw and alaw, I have a Cisco ATA186 with a Panasonic cordless phone attached to it, I have a Digum IAXy with a dumb analog phone attached to it, and I have a Linksys PAP2-NA with an AT&T 959 analog phone attached to it. I also have several

Hi, Just downloaded the latest cvs from zaptel on my sparking new Athlon64 Centos4.2 system, but hitting a stumbling block... (sorry for the long post) #make cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -m64 -DSTANDALONE_ZAPATA -DZAPTEL_CONFIG=\"/etc/zaptel.conf\" -c -o gendigits.o gendigits.c cc -o gendigits gendigits.o -lm ./gendigits cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -m64

My boss is insisting we support fax, and I keep telling him that Fax over IP is very unreliable and not recommended and his immediate come-back is "Vonage does it." and it's very hard to figure out how. I don't think Vonage does T.38, the Linksys/Sipura units they're using doesn't support T.38 to my knowledge. That means they have to be using G.711Ulaw to send faxes.