similar to: Asterisk on a WRT54G?

Hello to everybody, does anybody knows how to install Asterisk on a Linksys WRT54G(S)? I had read in the Wiki that it is possible. If somebody has a tip, this would help me very much. Regards Bastian

Hi all, Any one tried installing Asterisk on Linksys WRT54G? We have but facing problems with SIP to SIP calls. The phones ring and calls are established but we cannot hear any voice at all. I tried allow=all in the general section but did not work. So I forced ulaw. Can any one please check it out and let me know what is wrong? Here are the conf files: Asterisk Version: Asterisk

Hi all, We have put together a firmware for a range of inexpensive routers. It has been configured to provide optimum VoIP performance. We have internally tested it for number of months and it looks very good. You should be able to run it easily with 20+ phones on local network ( we still did not hit the upper limit ) assuming that you have bandwidth. Your VoIP will get prioritized over other

Did anyone see the article? It''s the first time I really noticed that these little Linksys routers are such a fully fledged linux machine with a decent processor and a replacable firmware. I am now itching to get one to replace the multipurpose firewall desktop machine. Has anyone experimented with the current state of the firmware and how advanced you can get with tc rules? For

Ok, I've done some more research and I don't think I want an FXO box... What I'd like to do is use BroadVoice (with their BYOD plan) and then run Asterisk on my WRT54G router. I'd also like to use my regular home phones without having to use a special "SIP" phone... (eg. I like my Vtech normal cordless phones) What do I need to buy to get this working? It sounds like I

Hi, We're installing an * box next week (pbxtra from fonality) and I'm trying to come up with a solution for remote users that want a phone in their home. I need VPN and QoS capability, wireless support would be a nice to have. Ethernet handoff is fine, i don't need integrated dsl or cable modem... I've been googling and cruising the list and can find bits and pieces

Hi folks. Please don't flame me but I've been googling around for days, read a tremendous amount, tried everything, and still no go. This is most definitely a typical newbie question. - I sure hope there's somebody(s) out there who'll humble themselves to help me out. I've set up an 'out of the box' basic Asterisk server running on Slackware Linux. - It basically

current setup SIP phone 192.168.1.30 --> linksys wrt54g sveasoft -- INTERNET -- (xl0) Firewall (xl2:172.16.0.50)--> (em1:172.16.0.101) Asterisk problem is RTP stream not oging trouhg from * to sip and vice versa. #1 and asterusk is pushing 192.168.1.30 back to linksys with 172 as return address.... or #2 asterisk trying to get back to me as 192.168 on public internet.. got

Hello All, I would be grateful for some help with this issue. I have gotten Asterisk to work with Broadvoice on outgoing calls only. When I try to call my Broadvoice number from another location I get a caller is busy message. My Asterisk box is behind a Linksys WRT54G. Could this be the problem? On the Linksys, I have port 5060 forwarded to the asterisk box 192.168.1.2. I have tried not

Is it possible to set up a non-forwarding bridge? I have two interfaces that I'd like to combine, where one is a fast main link and the other is a slower backup. I'd like traffic to go out the fast link only, if it is available, and failover to the backup if it is not available. I never want to forward packets between the interfaces. My specific setup is a laptop with a 100M ethernet and

Hello all, I have my * server setup behind a Linksys WRT54G on Adelphia cable. I have forwarded 5060,10000-10020, and another port set can't remember off the top of my head but I can't seem to connect to the * server from any locations that are direct connects to the Internet. Am I missing a portset for forwarding? If I use the name service (voip.*****.com) from my home connection on the

I'm trying to setup Asterisk on my Linksys WRT54G router and it appears to startup successfully (no errors) and it says it is listening on 0.0.0.0 port 5060, but I am unable to connect to it. I've tried "telnet localhost 5060" but it just says connection refused. I've also tried connecting from another machine on my network (eg. telnet 192.168.0.1 5060) but it also says

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

Hello, I am not able to open the web interface for the wrt54g router on the lan. Which port does it use ? Thanks Varun

Hi, I'm stuck doing an install with Polycoms at a small office with no RJ-45. They went wireless 100%, poor them. I insist on using Polycom unless it's impossible because that's what I am standardized on for many reasons. What's the best way/device to turn a wired Polycom 501 (or any Polycom for that matter) into a WiFi phone? Mike -------------- next part --------------

I'm running an AsteriskNow V1.7.1 with both a PSTN connection and fax machine. Both are connected to a DAHDI board. I'd like to route incoming PSTN fax calls to the extension of the fax machine and process non-fax calls through different dialplan.logic. What's the best way to go about doing this? I've looked into Fax for Asterisk, bit I'm not sure that I want it or NVFax

Hello, I've been fighting one-way-audio issues with asterisk and SIP extensions for some time..., and I want to share with you my findings ;) My setup: * 1 ADSL router (Zyxel) * 1 Asterisk box with private IP, and interesting ports forwarded to it. * Several extensions, some local some remote The problem: * External extensions behind double nat don't get audio when they

Its slow :) It will give you some delays but it will not be noticeable (most voice files are 5-100kb, so it should be ok... But writing to them.. Not sure.. It should be ok as well I'm guessing as kernel will provide some caching (since you have G and not GS it has less ram, so maybe chaching is not an option) Best would be to get WL-500G. It has a USB port so you can plug a USB memory stick

I just bought two new Linksys WRT54G routers. Sveasoft has loaded Linux on this router and included a bunch of Linux tools, one of which is Bandwidth Management. The QoS aspect of this is supposed to be much more granular than the previous solution (Wonder Shaper). I have not been able to find any suggestions for how to impliment QoS (Bandwidth Management) using the web interface of Alchemy.

Hi, I've just installed asterisk 1.2.1 on my openwrt distro ( I own a WRT54GL by Linksys ) . No problem by now, but I can see that my 3 snom 320, once they started they send subscriptions to asterisk, and I can see that running: sip show subscriptions But, after one hour about, OR when I do asterisk reload , asterisk losts all th snom subscriptions. Someone can help me please? Thanks