similar to: E1 + sangoma + soekris

Hi All, I have a Soekris 4801 running Asterisk and I tried to add a X100P FXO card only to find that the Soekris will not boot with the card installed. The LEDs flash for a second and then nothing, it does not boot. I've tried 2 different X100p cards, both of which work in a regular desktop system, and still have no luck. I tried a different Soekris 4801 with no luck. I've also tried a

Hi group, i'm brand new and i would like to ask about soekris hardware. I read along the web but i have some doubts that i think can be solved here. My question are the following: 1) does the Digium TDM400P fit in the soekris box with a 4801 SBC or a bigger box is needed? Any suggestions about where to pick up another box? 2) does the Digium TDM100P (already discontinued) fits fine in a

Hi. I am trying to use EXTLINUX 3.08 to boot a Soekris net4801 from a CompaqFlash card. BIOS reports the CF card as the first master harddisk. During boot/load the loader hangs after this output: EXTLINUX 3.08 2005-05-19 PXELINUX and LILO works fine on the same setup It this a general problem with Soekris/net4801 and EXTLINUX? Regards Johan Linn?r

We found at the wiki a link to soekris and wonder if it is good? Is anybody using it and can share some experience, please? We would like to use it as a small PBX including a wireless access point, so that we can also use WiFi phones. bye Ronald

I thought I saw a Soekris embedded in the Digium booth photos, can you run Asterisk on one of these? How? I'd be interested in it for a back pbx, given the reliability. In fact, might want to move my home pbx to this also. Chris Mason

Dear all, I'm trying to boot a recent PXELINUX on a brand new Soekris net4501 (comBIOS 1.33). This combination appears to not work out of the box... I see much advice floating around from a few years ago, hinting that earlier versions of PXELINUX might have worked. However before resorting to archaeology I'd be interested in feedback from others who might have got through this. I

Hello - I've been running Asterisk (quite happily!) for several years now using a Digium TDM400P card in an old Linux box (P4 1.6 w/ 256MB RAM). I'm also running another old PC running m0n0wall as a firewall. Between these two boxes, that run 24x7, I'm drawing a lot more power than needed and hoping to make a dent in my monthly electric bill by consolidating the two into a single box

Has anyone on the list used a Soekris engineering PC as a TDM - Ethernet bridge? For example something like a net4801 with a TE110p in it and then using TDMoE to get it into a bigger server where the call processing proper will occur. Anyone know if it might handle a quadspan card ok? (no transcoding, just pure PRI to TDMoE bridging). Craig

Hello, Recently I have discovered a problem with serial console output when net-booting a Soekris net5501 board via pxe. When using pxelinux.0 from syslinux 4.04 package I get only 15 characters from the output, then the carriage returns back to the same line over and over again, making it impossible to read the output. What is more the booting process (trying configuration files with

I'm working with a Soekris net45xx SBC and I'm experiencing problems using any syslinux code (syslinux, pxelinux, extlinux) above version 2.20. I'm interfacing with the Soekris via the serial console port, which is the primary bios console. I've tried different configurations with setting serial in the config file, but no change (though I dont even thing it's getting to reading

Hi, Wich mini Linux distribution do you recommend? My idea is to use Shorewall in a Soekris mother, with some mini Linux installed. Thanks and Best regards, Andrés

I'm considering that board as a mail and voip gateway for home use. In view of all those statements about how little resources asterisk needs, did anybody already try running asterisk on it? Thanks, Bruno.

Hello, Freebsd-stable. I installed 7.1-STABLE on my new Soekris net5501. Kernel config is in attach. This unit lock up in strange way every day. It is pingable, but no access to host on any network protocol (sshd, named, etc are not answering), and serial console (only one this unit has) DOESN'T ANSWER too! Only way to un-freeze it is cold reboot. I've thought, it is

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

Skipped content of type multipart/alternative-------------- next part -------------- Console logs from Asterisk A: Executing Dial("SIP/test0-5821", "Zap/6/327557670||Tt") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 6/327557670 -- Zap/6-1 is proceeding passing it to SIP/test0-5821 -- Accepting UNAUTHENTICATED call from 195.66.73.122:

Hello Everyone, I am having trouble with booting a soekris 4826 board.after setting up my tftp,dhcp and web servers ,I log into the board using minicom and type boot f0,which doesn't quite work out. > boot f0 NSC DP83815/DP83816 Fast Ethernet UNDI, v1.03 Copyright (C) 2002, 2003 National Semiconductor Corporation All rights reserved. Pre-boot eXecution Environment PXE-2.0 (build 082)

Hello, I have a Soekris net4501, which I'm PXE booting using pxelinux. Everything seems to be working splendidly, except for the fact that I can't seem to make pxelinux understand use the net4501's serial console port correctly. The net4501 uses the serial console as its primary interface; I'm using a null modem cable and minicom to operate with it. At boot, its startup

Is anyone using a net4801 and an analog only setup? I am looking for a modem that is PCI 3.3V, apparently the X100P is 5.0V PCI only so it won't work with the net4801.

It would be a real kick to get one of these to run Asterisk. :) http://www.gumstix.com/ Tim -- >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>

Hello, Is there or can anyone provide a comprehensive guide (designed for Linux/Asterisk novices) to installing/setting up Asterisk in order to support Fax2Mail service? In my case, I would like Asterisk to receive fax calls to predefined numbers (ranges) and to associate each of these numbers to email addresses. Thank you in advance. David --------------------------------- Yahoo!