similar to: No zap/sip/etc options?

Hi, I am trying to upgrade my system (running 2.4 kernel) from 1.0.9 to 1.2.6, everything upgraded fine, however asterisk is not seeing any zap/sip/iax2 channels. I compiled in this order: libpri/zaptel/asterisk. Zaptel comes up fine... ztcfg -vv shows all of my channels, however asterisk lacks the 'zap show' 'sip show' or 'iax2 show' commands, further, if I try to force

Hi, I've noticed that sometimes instead of getting a regular ring tone when calling out on a Zap channel, I get this obnoxious loud noise which forces me to hang up. Is this a problem in the Zaptel driver? I seem to recall that ringback tones are generated by zaptel when dialing out from a SIP phone over a Zap trunk. Thanks.

When I call meetme: exten => 1000,1,Answer exten => 1000,n,Meetme(|||d) Asterisk is complaing with: -- Executing Answer("IAX2/xxx.yyy.142.204:4569-2", "") in new stack -- Executing MeetMe("IAX2/xxx.yyy.142.204:4569-2", "|||d") in new stack -- Playing 'conf-getconfno' (language 'en') Warning, flexible rate not

Before you jump ahead, yes I do have chan_zap.so loaded.. Call Flow: Asterisk 1 --IAX2--> Asterisk 2 ---> PRI -- Accepting AUTHENTICATED call from 22.22.22.22: > requested format = ulaw, > requested prefs = (), > actual format = ulaw, > host prefs = (ulaw|alaw|gsm), > priority = mine -- Executing

I need your help I have a sangoma A104D on my dell server; I got card status ok with no alarm If I dialed the extension 6210006, it shows the output as stated below, but there is no ringing from the pstn number nor the iax softphone am using on my pc. I will be glad if someone can give me a working config? What I want to achieve is to send all my call to the pstn on A104D? The pstn am

Hello Everybody, Since I upgraded to 1.4 I always get the difficulties as below, which I have never had in 1.2: [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Call accepted by 202.153.128.34 (format g729) [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Format for call is g729 [Dec 28 21:06:00] VERBOSE[1756] logger.c: -- IAX2/VoIPRakyat-2 is ringing [Dec 28 21:06:00] DEBUG[1756]

Please can someone help me with the following two error messages: Error 1. I have loaded the Zaptel dirvers and everything is ok with ztcfg. I have configured Zapata.conf and everthing looks good but it apears the Zap channels dont load when starting Asterisk. When I make a call to one of the fxs port I get the following error message. -- Executing Dial("SIP/39-b204",

I have 12 T1's going into 3 servers, 4 in each into "Digium, Inc. Wildcard TE410P Quad-Span togglable E1/T1/J1 card 3.3v (rev 02)" cards. Each "group" of T1's have the primary D on 24 and the secondary D on 96. The first server (ts20) and the last server (ts22) can playback "demo-congrats" fine. The "middle" server (ts21) cannot -- just dead air.

We have a machine with a TE410P in it acting as a client to route calls via iax2 to our central server, caller --> ( zap -> iax ) ---> ( iax -> whatever ) --> called client server often the called can't hear the caller (both machines on public ip) 'iax2 show netstats" on client machine shows more and more dropped packets on the

I am using asterisk version 1.2.6 with Zaptel version 1.2.5. I have a POTs line coming into a Digium TDM01B. It appears to not be getting CID at all. If I hook up a POTS phone to the line CID comes through fine. Inbound and outbound calls work fine but there is just no CID on inbound for this channel.The incoming route for the channel is Zaptel Channel 0. No DID or CID settings applied. My IP

I've just installed an X100P, built the kernel module, and tried to use it to make an outgoing call (via a phone connected to an ATA-186). However, I just get a reorder tone and see this on the console: -- Executing Dial("SIP/ata1-4409", "Zap/1/5551212") in new stack NOTICE[1200825920]: File app_dial.c, Line 481 (dial_exec): Unable to create channel of type

Hi, I still cant dial out on Zap and I really have no clue why. I'm using Asterisk Asterisk 1.2.6 and Zaptel 1.2.5 with Digium card 4 ports, 31 channels each and able to receive incoming calls and fax perfectly. I've done this in my dial plan. exten => 111,1,Answer() exten => 111,n,Ringing() exten => 111,n,Wait(2) exten => 111,n,AbsoluteTimeout(30) exten =>

Robert, Essentually I want to be able to have Server B dial the extensions connected to server A as well as route calls to the outbound route on Server A. Server B will have little to no knowledge of what is on Server A. I just want it to dump the calls off. For some reason I keep thinking this was a PRI type of thing. Like there was a module that loaded up as a fake PRI that your

I just installed a new TDM400P with one FXO interface in slot 4 (how it came from Digium). This box is running Debian with a 2.6.10-rc2-mm3 kernel. After the make linux26 and make install in /usr/local/src/zaptel, I can see contents in /dev/zap but any attemp to touch for example /dev/zap/ctl gets a no such device or address ... Any suggestions?

I'm getting this messages trying to call with one sip trunk: Feb 3 16:43:09 DEBUG[3389] channel.c: Avoiding initial deadlock for 'SIP/usa-e2ea' Feb 3 16:43:09 VERBOSE[3491] logger.c: -- SIP/usa-e2ea answered Zap/1-1 Feb 3 16:43:09 WARNING[3491] channel.c: No path to translate from Zap/1-1(68) to SIP/usa-e2ea(256) Feb 3 16:43:09 WARNING[3491] app_dial.c: Had to drop call

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 hi, i'm new to * I've installed an hfc-s card (DIGI Micro V) with bristuff 0.0.2; when i try to call outside i get: -- Accepting AUTHENTICATED call from 192.168.1.110, requested format = 1024, actual format = 1024 -- Executing Dial("IAX2[pippo@pippo]/2", "Zap/g1/0123456") in new stack Jul 13 13:42:49

I have: RedHat 9.0 TDM40B asterisk-0.9.0 compiled from sources zaptel-0.9.1 likewise /etc/zaptel.conf contains fxoks=1-4 loadzone = us defaultzone=us loaded modules zaptel and wcfxs /etc/askterisk/zapata.conf contains [channels] language = en signalling = fxo_ks context = phones channel => 1-4 /etc/askterisk/extensions.conf contains [general]

Dear all, I think this is common, or at least how it is supposed to be, but whening dialing over a ZAP channel, it's taking around 5~ seconds to ring on the over end, likewise inbound. This is just with a normal Dial command. Are there any ways to tweak this? Thanks, Gavin.

I have a TDM-400P with one FXO module. On an incoming call, I have set Asterisk to dial my phone (exten => s,1,Dial(IAX2/carey)), which is basically the only thing in my dialplan. When the call is answered by the PSTN phone first, or when the ringing call is hung up, Asterisk keeps ringing for 5+ seconds, which causes trouble (the answering of already answered calls). I noticed in the

I have a system with two 4 port T1 cards, with 5 PRI's configured. Each PRI is configured as an individual PRI and belongs to it's own group (groups 1-5) This system is handling roll-over from another system, where any error in processing the call on that system results in it being sent here. This mainly results in all calls resulting in a busy being sent for retry here. I then