similar to: Registering to H.323 Cisco gatekeeper

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

Hi list, After several tries to understand the subtil description in the h323.conf to be able to make the next scenario I was presented the following error messages by asterisk. Can somebody tell me please what I am doing wrong. Scenario: Gatekeeper (h323) --> Asterisk PBX -->(h323) Gateway Endpoints are connected to Gatekeeper. Call does come in like 999931235650087 with codec g711

Hi, I want to configure * to use a gatekeeper for routing calls to H.323 endpoints. I imagine it will work like that: * (chan_h323) will query the gatekeeper where to terminate the dialed number and the gatekeeper will return the information for the h.323 gateway. after that chan_h323 will try to make the call to the gateway it has received from the gatekeeper. so instead of duplicating a

All, I'm haveing a bit of trouble getting my head around H.323 and call routing with Gatekeepers, Zones and intra-zone calls - hopefully someone who is more informed in things H.323 will be able to point me in the right direction...? I already have a mature network of Asterisk boxes dotted around the UK and overseas with hundreds of extensions and our own number-plan/dial-plan in the form

Stephan, Ok, I'll re-state the problem... I have two devices that I want to talk to each other: 1. an Asterisk PBX 2. a Damm Cellular TETRAFLEX digital radio system (www.damm.dk) both devices are effectively "gateways" because they have many subscribers behind them. The Damm Cellular system controller is based on Windows-XP Embedded and its sub-systems used the OpenH323

I've read through the archives and have picked up that * does not need a gatekeeper to talk directly with an H323 handset to send and receive calls. I'm trying to go PSTN----*-----H323 and all the examples that I can find use a gatekeeper. Are there any examples or hints for doing it without the gatekeeper? many thanks in advance Brian

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i have a working Microsoft ISA firewall with buildin H.323 Gatekeeper.... So Far, i got registerd the asterisk on the M$ Gatekeeper... here is the h.323 configuration: ; Open H.323 driver configuration ; [general] port = 1720 bindaddr = 0.0.0.0 allow=all ; turns on all installed codecs dtmfmode=rfc2833 gatekeeper =

Hello, I'm trying to register with a gatekeeper using chan_h323, I have a Login, Password and a user (telephone) number, This is my h323.conf [general] port=1720 bindaddr=x.x.x.x (my fixed IP) gatekeeper=x.x.x.x (gk ip) allowgkrouted=yes allow=all [xx] (my login) type=h323 e164=111 (my assigned phone number) secret=1111 (my password) context=incoming I'm getting this error when trying

Has anyone had any luck getting Asterisk 1.6.2.13 to register to a Tandberg Gatekeeper? The logs on the Asterisk end seem to show that the registration request is sent, and the Tandberg Gatekeeper responds. However, the response doesn't seem to be what Asterisk was expecting. Here is my ooh323.conf, followed by the relevant portion of the h323_log: [general] port = 1720 bindaddr =

Hello everybody, First time installer and I need the lists advice. My plan is to use asterisk PBX with some hardware to terminate my calls coming from several operational gnugk gatekeepers. Do have RH9 and downloaded the latest asterisk from CVS. Compiled according instructions and is running fine. Could hardly find any info on h323 implementation untill the REAME in the channels directory.

Hi all, i have tried to connect to a clarent gatekeeper. I have used both of h323 drivers chan_h323.so and chan_oh323.so. But no one can register to this gatekeeper. Our ip is activated on this gatekeeper. Maybe, i do wrong anything.... I have only set the "gatekeeper" option in the h323.conf or oh323.conf to the ip address from the gatekeeper. gatekeeper=x.x.x.x But no one of the

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Hello, Thank you for the job well-done. I installed the chan_h323 of the asterisk-1.2.7.1 and with lib pwlib-v1_10_0-src-tar.gz and openh323-v1_18_0-src-tar.gz and I used licensed g729 from digium. However, I am having a very funny behavour. 1. If I send a call on its ringing at the called side but the caller didn't get the ringing tone. 2. if the called picks up the phone, I am

I'm trying to connect an Asterisk 1.6 to an Avaya with gatekeeper (CLAN). When chan_ooh323 first loads it tries to establish a connection with the gk but I it fails. I have the following extract from the ooh323 log. Can anyone give some insight? Thanks! MD 23:02:59:045 Sent GRQ message 23:02:59:045 GkClient Received RAS Message 23:02:59:045 Received RAS Message = { 23:02:59:045

I have tried everything. to register with this gatekeeper to make and receive calls These are the details I received from the voip provider: protocol H.323 Gatekeeper Address - AVS@210.21.118.XXX Port - 1719 RAS - 53 Q931 - 80 h245 - 1722 RTP - 1722 Username - H323 I have 2 phone number/accounts with this gatekeeper that I need to register to. ID - HMA0200.10szxn-xxxx e.164 - 22xx2912

hello everyone i have a simple question: i have an asterisk which is a h323 gateway and has a h323 connection to a cisco gatekeeper and a sip connection to a pbx. my question is: how can i send all calls to gatekeeper? i searched a lot and found that i should set gatekeeper=192.168.0.X (ip address of my gatekeeper) in h323.conf file. but what about extensions.conf file? should i define an

Hello I am a newbie to Asterisk. We have set up Asterisk on a PC with Redhat 9.0. We have installed H323 openphone on our PC's. We are wondering what a gatekeeper does. It seems we need one but what I have seen in this group is that a gatekeeper must be installed on another box on the network. As all our PC's on the network use Microsoft OS is there a free gatekeeper software for

All, I've fixed my problem getting Asterisk ooh323 channel to stay registered with my Cisco IOPS gatekeeper, now I need to get dialling working. I have the following: [Asterisk with ooh323] ----h323---- [Cisco IOS GK] ----h323---- [Radio system OpenH323] 192.168.1.5 192.168.1.6 192.168.1.7 the Asterisk box has numbers

Dear All, I have enabled the gatekeeper in oh323.conf file. I started the gatekeeper and also restarted the Asterisk. When I called, it was worked fine. After then enabled the routing mode in gatekeeper.ini file then I restarted the gatekeeper. When I called the routing mode didn't work. I have received the following warning in Asterisk console. " Jul 21 14:19:11

Hi! I am trying to do a SIP/H.323 gateway. I want that the SIP proxy server (I suppose that this is asterisk isn't it?) has all the information about the user's registration. So, when a request arrives at the gatekeeper from the H.323 network, this one tries to make multicast to all the others gatekeeper and also the Gatekeeper Asterisk. Asterisk then looks for if the user called is a