similar to: No sound in one calling direction, men using PRI with E1 and Q.SIG

When inserting Ringing() before MeetMe()-conference picked up the call, everything works like a charm. I guess the PRI needed to see the ringing status before the call was answered. This is however never needed when dialing a SIP-extension or similar. I have also an update considering bad PRI b-channel numbering. It seems that only my first 15 channels actually work. Then our PBX tells Asterisk

After lots of testing I discovered that I could get the sound to work. The only thing I had been testing was MeetMe and Voicemail. But when I dialed a SIP-phone, or routed back to other phones via the PRI interface, everything works just great! The problem only seem to occur when dialing directly into Asterisk, when Asterisk sends the audio output. I have also discovered that the PRI never seem to

I'm using QSIG between Asterisk and an NEC SV8300. Whenever I make a call from the SV8300, I see: [Oct 4 21:02:49] ERROR[5729]: chan_dahdi.c:12226 dahdi_pri_error: !! < Unknown IE 50 (cs5, len = 3) I see an IE 50 in the Q.932 specification, so I don't understand why this error is occuring.

Hi everybody. I'm about to ask a newbie question, be warned! I have a NEC 2000 IPS PBX connected to a E1. Now I want to set up an asterisk, with some digium card connected to that E1. (suggestions about the card? I'll have maybe another E1 more). The "newbie question" is.. How can I connect the asterisk PC with the PBX? I don't know so much about E1, so I don't know

Dear all I have asterisk 1.2 and now i want to install E1 card with support Q.SIG singaling so which E1 card is best for my setup i need single port E1/PRI card which support Q.SIG Regards Satish patel --------------------------------- Take the Internet to Go: Yahoo!Go puts the Internet in your pocket: mail, news, photos & more. -------------- next

Hi! I want to test Asterisk<-->Siemens HiCom integration using Q.SIG instead of ISDN. I did not find any documentation about Asterisk und Q.SIG. Thus, I wonder is it sufficient to set "switchtype" from "euroisdn" to "qsig" or are there any other things which I have to take care of? Thanks Klaus

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

Add an Answer() as your first step in your dialplan and see if that help. snip

Hi, I'm using samba in RedHat Linux 5.0. It works almost ok... First of all, I think everything is MUCH to slow. I am running it on a Pentium Pro 200MHz with 64Mb RAM. And there is only 5 clients using it. I'm using version 1.8.19p3 on an RedHat 5.0 Server. Is there something special I need to do about the filelocking?? Or have I just done something wrong during setup...? Before this

hi, after several problems getting the right callerid on a E1-PRI there is (so far) only one problem left: when receiving calls over the telephone network from another E1-PRI that has a "Caller ID no screen" capability (e.g. a bank and a customer of us), asterisk does not get the callerid that is set up by the calling PBX, but the callerid of the trunk of the calling PRI. no matter

Hello, if somebody using this scenario in production successfully, please send me info, which ISDN card for asterisk server is usefull for me (Digium, Sangoma)? my crucial requirement is "caller id name" transfer/display between ISDN (Siemens PBX) and IP phone connected to asterisk I'm using PRI interface and Q.SIG signaling. thank you PJ

Hello, I am using a Cisco-2,811 as a gateway between the Asterisk PBX and our Nortel TX-1 university's PBX. It is working but no names are exchanged. From the debug mode I see that the Cisco sends the display name (which does not appear on the Nortel's phones) and the Nortel does not bother to send it at all. I recall that when I had a pilot with Cisco CCM two years ago we had to set

Hello everyone, My setup: Debian squeeze Asterisk 1.8, DAHDI, libpri, compiled from source TE110P, attached to a Deutsche Telekom Octopus E Modell 300/800 I'm trying to get MWI for Voicemail working. In the same server I have also got an Eicon DIVA PRI card for testing purposes (it is integrated via CAPI and the chan-capi channel driver into my Asterisk). MWI works just fine there. I

On Mon, Nov 17, 2008 at 10:20 AM, Tony Mountifield <tony at softins.clara.co.uk > wrote: > > If I do this from an NEC digital extension I get 141496920000, but if I > do > > it from an NEC POTS extension I get 1942124000 > > That looks like when you pick up the analogue phone and dial 9, it > immediately opens the outgoing line and sends the 141 acces code, but >

hi, i have the problem that i'm not able to set and receive the Service Indication (SIN) from our E1-PRI and from our ericsson BP250. The problem is, that the Bearer Capability (BC) together with the High Level Compatibility (HLC) and Low Level Compatibility (LLC) forms the Service Indicator (SIN). The SIN is used to determine if the call is voice, fax or data. It's essential to set

Hello all, I have the following working (somewhat) setup: TELCO | | E1 (30 Chan -- TE210 SPAN 2) | | Asterisk box 1.6 with DAHDI drivers loaded Digium TE210p | | E1 (30 Chan -- TE210 SPAN 1) | | NEC PBX

> Close. 10/100mbps Ethernet uses wires 1,2,3,6 but that is pair 2 & 3. > Pair > one is the pair up the dead center (pins 4&5), pair 2 is pins 1&2, pair 3 > is > 3&6 and pair 4 is 7&8. A T1 uses pairs 1&2, which is why you can't use a > regular crossover cable for a T1 crossover, but you can use a regular > ethernet patch cable as a T1 patch

Hello List I'm trying to figure out what is wrong between my asterisk and my NEC 2400 pbx We have been trying to link them with a spare PA-24DTG from the NEC, I'm able to call an extension on the Asterisk, however the extension rings, and then immediatly hangs up I traced it back to the debug of the PRI on the Asterisk... I would appreciate if anyone could pin point what is wrong The

Hello, Have you seen the log-linear prediction of the 100m winning time in R mailed to the list yesterday by David Smith, subject Revolutions Blog: July roundup? "A log-linear regression in R predicted the gold-winning Olympic 100m sprint time to be 9.68 seconds (it was actually 9.63 seconds): http://bit.ly/QfChUh" The original by Markus Gesmann can be found at

Hi every all I use ubuntu 10.10, wine-1.3.7, winetrick, directx 9.x. X-Men Origins: Wolverine dosen't work. It's start but after give me this error: Code: /media/a50382d0-eb99-4db6-a1d5-194cac9812e5/Programmi/xmen/Binaries$ wine Wolverine fixme:gameux:GameExplorerImpl_VerifyAccess (0x136fe0, L"D:\\xmen\\Binaries\\Wolverine.exe", 0x3dbf620) fixme:win:EnumDisplayDevicesW