Displaying 20 results from an estimated 1100 matches similar to: "Channel Restart and Dropped calls"
2012 Dec 21
2
dahdi timing source multiple cards
I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting
slips and ask me to update the clock source. I have my system.conf set as
the following but when I run dahdi_scan only the ports on Card 1 are showing
up with syncsrc=1
system.conf :
span=1,1,0,esf,b8zs
bchan=2-24
mtp2=1
span=2,2,0,esf,b8zs
bchan=26-48
mtp2=25
span=3,3,0,esf,b8zs
bchan=49-72
2009 Aug 24
1
E1 w/ TE420B EC
I keep getting a red alarm when trying to setup asterisk to use my
TE420B EC. I only have a blank context setup in my extensions.conf as
I haven't started to config that until I can clear this red alarm. I
don't have physical access to the server, so I can't go reseat the
modules/card/ethernet cable, though I have hands on location that have
done this a couple times
2010 Jul 19
1
Problem with E1
Hi All,
I am facing problem with E1 line. I have installed Asterisk
(1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10)
But every
now and then I face problem of down E1's. The log show lot of entries like
"pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of
span 2"
This happens on a regular basis and the E1 becomes up after some
time.
My
2013 Mar 21
2
Need help about round-robin
hello list,
i have installed 2 diguim cards in my server using asterisk 1.4 (i use the
old version with zapata.conf and zaptel.conf)
i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i
want to active the round-robin for span 2 and 6) in order to activate the
WIMAX and FH
please see the configuration below and tell me if there is anything wrong
question 2: what is
2007 Dec 03
2
Red Alarm TE420 with E1s - R2
Dear members of the list,
I have difficulties to obtain sync with a Digium TE420 PCI Express
For four entries E1, In my case I am with only 3 E1s available to
configure. The
telephony operator is BrasilTelecom and Signaling is R2 Digital.
The information I have is that are E1s with 32 channels, not have
sure. My settings
Have been based on the link reference:
2009 Dec 04
1
DAHDI issues on 1.4.26.1
Hi,
Running 1.4.26.1 here. I have installed TE420B card in my server, and
followed the appropriate steps (as far as I know to configure it). This
TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling
type.
When I dial out, I get this message:
Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to
create channel of type 'DAHDI' (cause 0
2006 Dec 18
2
Digium TE405P with French E1 => Red Alert
Hi
anyone have a idea for debug my digium TE405P card ?
My zaptel.conf:
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
loadzone = fr
defaultzone = fr
My Zapata.conf:
[channels]
language=fr
context=from-E1
switchtype = euroisdn
pridialplan = unknown
signalling = pri_cpe
usecallerid=yes
hidecallerid=no
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
2010 Jun 16
2
DAHDI PRI error message
Hello-
After configuring DAHDI and starting asterisk, I get the following
message continuously on the Asterisk console:
WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels
available! Using Primary channel 16 as D-channel anyway!
My card is a D410P configured for E1, only the first span is configured,
and configuration snippets are as follows:
From /etc/dahdi/system.conf:
2010 Apr 30
1
HDLC Receiver overrun on Wildcard TE410P
Hello
I've got small PBX (30 simultaneous connections) based on asterisk
(1.6.2.6), which uses Stargate 2N ISDN to GSM gate.
It runs ok for day or two, but then I get:
dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16)
in my kernel logs, in asterisk i get:
pri show spans
PRI span 1/0: Provisioned, Down, Active
PRI span 3/0: Provisioned, In Alarm, Down, Active
(span 3
2009 Dec 22
2
E1 R2 Congestion Status
I have a 'CONGESTION' Status with R2 protocol.
While testing this scenario sip GW--?Asterisk ?Digium E1 R2
Protocol?Cisco E1 R2 protocol?sip Gw
Find below my error and configuration ,where are the errors in my
configuration ?
=========================================================================
Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on
2009 Nov 09
3
E1 Extensions.conf
Hi,
I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card
5.0V (rev 02)) 4 ports
I want to make a loop test between digium card E1 to test the
configuration of dahdi
What I want to do scenario is
I connect port 1 and port4 in the digium card with E1 cable
SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local.
kindly can any can help me to
2008 Mar 05
1
Newbie dialplan: dial 0 for outside line
I just managed to put in a TE410 card in an Asterisk box to work with
OnRamp 20(E1 downunder). I am able to dial in but was not able to dial
out.
Can anyone offer me some advice please?
In my extensions.conf, I just put in:
[default]
...
exten => 0,1,Dial(Zap/g1)
and I get this on the console when I dialled 0.
-- Executing [0 at default:1] Dial("SIP/5166-b76004f8",
2011 Feb 17
1
Setting two E1 cards
Dear, I always had one E1 card with one span, so I've never had any
problem in set it up through /etc/dahdi/sustem.conf and
/etc/asterisk/chan_dahdi.conf because I put span=1.
But now I have a PBX with two E1 cards with 4 span (8 span in total).
How do I have to define both card in system.conf and chan_dahdi.conf,
and how do I have to refer each span to the corresponding card ???
Thanks a
2010 Jun 12
2
Qwest PRIs
Hi,
I'm trying to bring up two PRIs from qwest with asterisk and dahdi. I'm
using an OpenVox D410E and the drivers are loaded. My system.conf looks
like this:
# Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF RED
span=1,2,0,esf,b8zs
bchan=1-24
# Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" (MASTER) B8ZS/ESF RED
span=2,1,0,esf,b8zs
bchan=25-47
dchan=48
These
2010 Jul 08
1
Incoming call doesn't finish when internal phone hangs up
Hello guys,
I have this problem when a call is received in my PBX:
(Caller) --> (Redirecting Service) --> (E1 PRI) --> (Asterisk PBX) -->
(Internal Phone)
Reception works fine, but when conversation finishes and the agent at
internal phone hangs up, the call at caller's side is still alive for
many seconds until it hangs up.
The problem is that Telephone Company is billing me
2009 May 20
2
asterisk crash on DAHDI error: No more room in scheduler
Hi,
I'm getting the following error from an asterisk 1.6.0.9 installation:
[May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error:
Asked to delete sched id -1???
[May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No
more room in scheduler
This repeats a few times, then asterisk crashes. I can't seem to locate
any info on this error at all. I'm using
2013 Feb 26
0
activation round-robin
hello list
i have installed 2 diguim card in my server using asterisk 1.4 (i use the
old version with zapata.conf and zaptel.conf)
i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i
want to active the round-robin for span 2 and 6) in order to activate the
WIMAX and FH
please see the configuration below and tell me if there is anything wrong
question 2: what is
2005 Sep 30
1
TE410P not working
I'm trying to install a TE410P this is what happens with compiled zaptel
1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/
this is my zaptel.conf (checked with the provider the values):
span=1,1,0,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16
loadzone=it
defaultzone=it
then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says :
Sep 30 16:12:40 localhost kernel: Zapata
2006 Apr 30
2
PRI Issue: D-Channel woes
Hi,
I am about to pull my hair out after trying to get our PRI up and working.
We are switching from a Cisco gateway to an Asterisk box which provides
the 23 phone lines for our office. So, because the Cisco gateway is
working I can assume I have all the settings right (b8zs, esf, dms100,
etc) and the PRI is live (because we are switching over). When dialing
from PSTN, I get busy signal. When
2009 Feb 02
1
Preferred Clock
Hi,
We're running on a * 1.4.21 system. We run about 80 SIP Extensions, mainly
ATCOM phones (and a few Snoms - 300 and 360), and have an additional 80 IAX2
extensions to iaxmodem devices for fax2email. We are rapidly growing and
will be adding an additional PRI trunk and grow to about 150 SIP & IAX2
extensions towards the end of the year.
We have two Digium Wildcard TDM800P cards (8 x