similar to: HINTS with Polycom stops working after aster isk reload

Dear Users, Recently I have started using HINT option in Asterisk 1.2.4 with my Polycom 500 phone. What I have notice that for a day or two everything is working great but then HINTs stop working on my Polycom phone. It also happens when I reload asterisk from console. I do sip debug and I do not see anymore asterisk sending NOTIFY messages about my watched extension. To make it work again I

You have the session target as the IP address of the router's own ethernet interface. You probably want that to be the address of the Asterisk server instead. I also highly recommend you use full duplex ethernet, as voice packets don't really like to be restransmitted when a collision happens. -d > Message: 10 > From: "Bartosz Jozwiak" <bartek@cq-link.sr> >

>There is no real answer to your question. >just use one you're most familiar with. Second that, using FC2 for me, and it's the Devil You Know, right? I have a good handle on the RedHat Way which the Debian guys say is stupid, but it's not, it's just different. All of the little RedHat-y things you get used to and when you use a different distro, it's like, WTF?? I like

Hello, I have ISA card LineJack. I could not find any information if this card can work as fxo with Asterisk. If it can work, can somebody point me how to install it on my Asterisk box. Or maybe there is some documentation about it how to install LineJack. I will be very thankful for any help. Regards Bartosz Jozwiak ------------------------------------------------- This mail sent through IMP:

I am planning to buy Dell 2650 server with dual Xeon processors. And I would like to buy two TE410P cards for PCI with 3,3v. This is on Dell site about PCI slots for Dell 2650 server: 3 PCI-X (1x64-bit/133MHz, and 2x64-bit/100MHz) Does that mean I will be able to buy two TE410P cards ? Or I need to buy two TE405P cards ? Thanks for help. bartek

Hello, I have a question. I set up an extension to 1234 exten => 1234,1,Dial(SIP/1234@sip.greentone.com:5060) And when I dial that extension I got in SIP message "403 FORBIDDEN" Can somebody tell me why I cannot call that extension? When I am not using Asterisk I can call that extension without any problems. My SIP proxy is VOCAL. I am new here so I do not know a lot yet. Thank

You have no dial-peer telling the router what to do with the outbound call. http://www.tape.net/~gerry/asterisk/cisco26x0.html At 12:50 PM 9/26/2003, you wrote: >Like Gerry wrote for callerid you need VIC-2FXO-M1 card. > >Right now I am stuck on making outgoing call. > >Could soembody help me with the configuration. > >On cisco I have soemthing like that: > >dial-peer

I would like to release prepaid application. But I have a small problem, we are using their Cisco prompts (nice lady voice) And I do not know if it is ok to release it. Bart -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031201/db22d880/attachment.htm

Hi! AFAIK FGLRX doesnt support glx_ext_texture_from_pixmap, and enabling composite+dri is resulting in screen corruption even with 8.38.6. Then how are you guys running it without XGL? Regards, Karthik On 6/29/07, compiz-request at lists.freedesktop.org < compiz-request at lists.freedesktop.org> wrote: > > Send compiz mailing list submissions to > compiz at

----- Original Message ----- From: <asterisk-users-request@lists.digium.com> To: <asterisk-users@lists.digium.com> Sent: Wednesday, December 01, 2004 7:07 AM Subject: Asterisk-Users Digest, Vol 5, Issue 6 > Send Asterisk-Users mailing list submissions to > asterisk-users@lists.digium.com > > To subscribe or unsubscribe via the World Wide Web, visit >

hello, Is it possible to make attendant transfer (not blind) with ZAP channels ? bartek

When are 'we' going to have this solution Steve? :) You keep talking about it, and we keep asking when it's going to come about. I know myself, SS7 will be a make or break for our continued use of Asterisk. Even if we had some price indications would be good, and/or a timeframe? Don't want to seem pushy, but it's been on the cards for quite some time now. Ben -----Original

What is better? Cisco 7960 or Snom 200 ?? Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031028/befeaa4d/attachment.htm

Hello, Again one more question about hardware. What could you suggest me to buy. I need hardware to connect let's say 4 analog lines. (FXO). This hardware should "talk" to Asterisk of course.. Thanks very much for some advices :) Bartek -------------- next part -------------- An HTML attachment was scrubbed... URL:

It is possible to connect ADTRAN TSU 600 VP24 FXO 24 Port Channel Bank to Asterisk ? Somebody offered me that hardware, but I do not know if thats good hardware for Asterisk. rgs, Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030820/4a9e4608/attachment.htm

Hi Guys, Sorry about writing to that list but could not find better place. I have Grandstream BT-100 phone, btw, was working great with Asterisk. I have upgraded the phone, and during upgrade something went wrong. Right now when I power the phone I can only see some garbage on the LCD display. does not react on any buttons, pings,..... Maybe somebody has any idea if it is fixable or I can just

Hello, Is anybody there using quadBRI form Junghanns.net with Asterisk ? I would like to order that card but first would like to hear some opinions. Thank you in advance Bartosz

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz

---------- Forwarded message ---------- Date: Tue, 30 Nov 1999 12:14:09 -0800 (PST) From: David Cantrell <david@slackware.com> To: slackware-security@slackware.com Subject: Security Patches for Slackware 7.0 Available There are several security updates available for Slackware 7.0. We will always post bug fixes and security fixes to the /patches subdirectory on the ftp site:

Currently, the cube plugin uses mipmapping only when cube is unfolded. When the cube is rotated, mipmaps are not used, which leads to ugly look of textures. The attached patch fixes this. This leads to another kind of artifacts, which are fixable with anisotropic filtering. http://team.pld-linux.org/~wolf/aniso.png The leftmost image is the current state of cube plugin. The center image is with