similar to: GXP-2000 phones stop registering

I am having problems getting any form of call transfer working. I have reconfigured blind transfers to be #1 and assisted transfers to be *2 but these are not working. Looking at the wiki (http://www.voip-info.org/wiki-Asterisk+cmd+Transfer) it it does not mention IAX so I assume I have to use the native IAX transfer supported by Diax? I have tried using Diax but am getting a problem that after

Is anyone else having an issue with GXP-2000s and transmit gain? All my other phones are fine on my TDM400P with txgain set at 0, but the GXP-2000 caps at about a third of the scale in ztmonitor. I'm getting people complaining they can't hear me on my GXP-2000s, whereas my Snom 320 and Polycom 301 are great, and my Budgetones are overmodulating. Is there any conceivable fix on the

I have upgraded the GXP-2000 to the newest firmware 1.0.1.12<http://1.0.1.12>and the phone is much more usable However, I still have two slight sound quality issues: 1) There is static on the line at all times. It is not that noticable to me, but when I make calls out the PSTN the person on the other end hears it. If I use a Cisco ATA with an analog phone and call the same person again

I have loaded festival-1.4.3 patched with the 1.4.3.diff file. Festival source is in /usr/src/festival dir. When I try to use it I get this from asterisk: -- Executing Answer("SIP/chad-57a4", "") in new stack -- Executing Festival("SIP/chad-57a4", ""I am talking"") in new stack == Parsing '/etc/asterisk/festival.conf': Found

I'm using a few GXP-2000 with firmware 1.0.2.13 and everything seems to be working fine. However, there are a couple of issues I'd like to know if are possible: 1) Even though the phone has 4 line appearances, if I am speaking on a line, the phone can no longer receive phone calls. I can manually select another line and make calls, but when Asterisk tries to send a call to it, I

Hi, i got my Grandstream GXP-2000 phone today and want to configure it with TFTP. I downloaded the firmware 1.1.0.13 and put it into my tftp-server directory. Then I downloaded the template from: http://www.grandstream.com/DOWNLOAD/Configuration_Tool/Linux_Unix/Grandstream_Configuration_File_Template_1.0.6.x.txt renamed it to cfg<mac-address> Did the configuration in the new file and

Hi all Slightly OT but I know a lot of GS experts hang out here - I just upgraded a GXP-2000 to firmware 1.0.1.13 to try out the BLF functionality with Asterisk (which so far works as expected), but as a side-effect the phone won't sync with an NTP server - I've tried different server names (time.nist.gov and pool.ntp.org) and IPs in the config, but it refuses to update the time on

I just purchased a Grandstream gxp-2000, budgetone102 and a HT-386. Browsing to each device by IP address, I can get logged in using admin and I can see the advanced settings, however, if I try to change the settings and clicking the Change button, it just brings me back to ask for the password again.. I can't get into the Status page or any of the Account1-4 pages either. It just keeps

Anyone used the new Grandstream GXP-21XX series phones. We have been testing these phones and like what we see. We are looking for a greater cross section of testing before we roll them to production. Any feed back would be appreciated. We are talking with Grandstream engineering and they are looking for feed back as well. Any input is appreciated. Thanks Bryant -------------- next part

Greetings all I was wondering if any of you have found this problem. I have a setup with 80 GXP-2000s which work great until I decide to stop now my asterisk server. When it comes back up half of the phones (not always the same ones) fail to register with Asterisk. I set up the phones to register and send keep alives (register every 4 minutes, send keep alives every 20 seconds) to no avail.

Hi, I have a lot of GXP-2000 phones not registering with Asterisk server. After two days of attempts, it seems that problem is due to the fact that phones and server are not on the sme network. Do you know if this is known issue? -- Domenico Viggiani

Guys. I just downloaded the recent firmware for GS GXP 2000 and I must say the phone works great but... How do you make the conf button work?????? Anybody done that? Also, with great dissapointment I must ask, where is ILBC support? GS web page mentions it and the manual says it supports it almost using bolds :) soooooo where is it???? Any light on this?

I have a client with 20 GXP-2000s. Everything seems to be working fine. However, after a couple of weeks of use, the client is having a hard time adjusting to the new IP based phone systems and only misses one feature from their old Lucent system. That is, they had 8 analog lines before and all their old Lucent phones showed a button for each line. So, it was easy for anyone to say,

I've done some googling and searched voip-info but I'm not able to find a good answer about how to provision the GXP 2000. Based on questions I've asked before it seems like a lot of people are using the grandstream phones so I figure provisioning can't be that hard. Is everyone using the web interface for *every* phone? Or is there a better, more automatic, way? TIA!!! Thanks,

Hello I'm about to order a GrandStream GXP-2000 and a Linksys SPA-921 I'd like to have some user feedback about how those phones perform, and whether their LCD screen displays both the caller ID name and number (The GrandStream BT-100 only displays numbers, which isn't very helpful). Thank you.

Hi, I'd set the daylight saving option to yes on all the GXP-2000 phones, but apparantly it doesn't move it an hour back on last sunday of October. So now I am stuck will all the phones showing the wrong time. Isn't there an option so that it'll automatically update daylight savings? Thanks -- Zeeshan A Zakaria -------------- next part -------------- An HTML attachment was

Hi folks, Just a quick question. Does the GrandStream GXP-2000 phone support presence (hints)? Cheers, Richard. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060109/26c4a63c/attachment.htm

I have had 2 GXP-2000 for a while now and been slowly following the firmware releases made by Grandstream and am now up to 1.1.0.13. This version works really well on these 2 original phones (MAC's 00:0B:82:06:xx:xx), so I went ahead and ordered another 2 phones (MAC's 00:0B:82:09:xx:xx). One of these I upgraded to 1.1.0.13 (it came with 1.1.0.5) and pressed it into use. The Speaker

I've finally got a chance to play with 1.0.1.9, and the wiki has been updated. At the moment, I don't know of _any_ bugs with it. I'm yet to play with complex things like early dial, and will update the wiki as I find information. http://aussievoip.com.au/wiki-GXP-2000 I've just been given official permission to offer the firmware as a download, so if you visit

Can someone explain me attended transfer with Grandstream GXP-2000? Hitting TRNF button, I get: Dial number (BLIND) or Select line (ATTENDED) What's the exact meaning of 'Select line'? Thanks Mimmus