similar to: Re: Asterisk-Users Digest, Vol 21, Issue 38

a) jerjers been doing a lot commendable work for * b) support is not mandatory, and i agree with royk it should not be withheld based on political viewpoints, that's pointlessly draconian c) choice is always good, so people should have the option of oh323 or h323, let them decide, and not limit them, unless astmaster chooses to limit them, and that too based on valid points d) jerjer gave a

hi .. I have finally managed to get Chan_H323 & G729 working flawlessly, thanks to some help from Jerry McNamara. For those out there who are stuck with the same problem the procedure is : 1. install on RedHat 8.0 and nothing else (RH9 doesn't work!) 2. Install asterisk, zaptel etc. the normal way 3. Compile Pwlib & oH323 with versions taken from nufone's site

The hack below is for OpenH323, not Asterisk. This is not an Asterisk problem AFAICT. I am posting it here so that any other Asterisk user with a similar problem might benefit from it. I may or may not post it to an OpenH323 list, but since both variants of the H.323 channel in Asterisk use non-current OpenH323 versions, it may not be of any benefit to anyone anytime soon if I went that route!

Hello, I can use directed call pickup using pickup application (between sip, iax, skinny cals), but unable to pickup call that is ringing on phone behind h323 gateway (using original h323 channel in asterisk), is this even suported? thx PJ exten => _*7.,1,Pickup(${EXTEN:2}) console log, when trying o pickup ringing line 324 (h323), from skinny phone (953) -- Executing

---------- Forwarded message ---------- Date: Wed, 11 Jun 2003 01:10:16 +0200 (CEST) From: Siggi Langauf <langausd@fachschaft.informatik.uni-stuttgart.de> To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] chan_h323 + openh323 CVS = no go? On Tue, 10 Jun 2003, Jeremy McNamara wrote: > If you would have followed the build instructions laid out by the Open > H.323 folks

Successfully hooked up a Cisco CallManager to a local * installation via H323. Things are working fine when dialling from CCM to *, but I'm seeing a callerid of 'root' coming up on the CCM Phone when dialling into *. Is there any way of setting this to be something else? I'm guessing the name is coming from the ID that * is running as. I'm using the chan_h323 driver and

I have one and only one reason to use OH323, and that is it works with Cisco's CallManager. The standard H323 channel has one-way audio issues when connected to CCM and fixing them has been identified as a low priority/never going to happen task. Dan -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of

Hi, trying to build the h323 channel driver that comes with asterisk works fine, but only as long as I use openh323-1.11.7. Unfortunately, that setup seems to have a bug which misguides one of the audio streams. (So while * can "hear" me, the phone remains silent.) I suppose that bug is fixed at least in openh323 CVS. At least, I got things mostly working using the external

Hi I have found in http://lists.digium.com/pipermail/asterisk-users/2004-July/056111.html (Hack to make * -> (H323) -> CCM -> IOS GW work) that i need a special version of chan_h323, because of the External RTP problem. Do you know exactly which version is it? Or do i need an unofficial patch? Thanx Andr?s

Hello, I have a strange h323 issue. After executing command "Dial("SIP/333-0d1dfe00", "H323/361737052390920 at ccg|5|tT")" at Oct 18 22:32:23. Meanwile I have sniffing traffic on port 1720. The call was established just at Oct 18 22:33:03 (New H.323 Connection created.) and also packet sniffer grabs the h323 invites at this time also. So my question is what

At the present time you have to have a VALID ip address in bindaddr for Skinny to work. If bindaddr is either 0.0.0.0 or simply commented out all packets requiring the IP address contain 127.0.0.1. I forgot their nick, but someone in IRC recommended we make Asterisk be smart enough not to pick that interface, but I'm not sure of that is the problem or not. I simply have not had the

Hello All, I have been using asterisk for some time, and I would like for all to take a look at what NuFone does when they get something called out about their website. I ordered a 800 number from them on 3/4/05, they did not make me aware of the time that they took in provisioning and how terrible their support was. I called them on Tuesday 3/8/05 asked for a phone call because the

Hello everybody, First time installer and I need the lists advice. My plan is to use asterisk PBX with some hardware to terminate my calls coming from several operational gnugk gatekeepers. Do have RH9 and downloaded the latest asterisk from CVS. Compiled according instructions and is running fine. Could hardly find any info on h323 implementation untill the REAME in the channels directory.

Hi, I wish to know if GNUGk can work with * running as a gateway with the Digium FXO card. Kindly share your experiences in case there are some issues which one must know before going in for such a setup. Also, I've been reading about the DialTone detection capability by the hardware in different countries. What are the issues with it? Thanks & Regards, Deepak ----- Original Message

Hello all, I just installed Asterisk with H323 support (chan_h323 from Jeremy McNamara). But experience problem while connecting OpenPhone to Asterisk Here is h.323 trace: 5:37.444 H323 Listener:9c86de0 transports.cxx(1504) H323TCP Started connection: host=10.120.160.15:3172, if=10.120.160.99:1720, handle=27 5:37.444 H225 Answer:9cc1250 transports.cxx(564) H225

Hi list, After several tries to understand the subtil description in the h323.conf to be able to make the next scenario I was presented the following error messages by asterisk. Can somebody tell me please what I am doing wrong. Scenario: Gatekeeper (h323) --> Asterisk PBX -->(h323) Gateway Endpoints are connected to Gatekeeper. Call does come in like 999931235650087 with codec g711

I receive the following error when I try to call another H323 extension from another H323 when going through *. NOTICE[27669]: File channel.c, Line 1325 (ast_set_read_format): Unable to find a path from 1 to 8 NOTICE[27669]: File channel.c, Line 1296 (ast_set_write_format): Unable to find a path from 8 to 1 WARNING[27669]: File chan_h323.c, Line 528 (oh323_write): Asked to transmit frame type 1,

Hello, I managed to terminate calls from cisco: as5300 and 7206 to asterisk over h323. I tested both oh323 from inaccessnetwork and JerJers chan_h323. I used 1.12.2 version of oh323 and 1.5.2 version of pwlib. After latest changes from JerJer chan_h323.c works ok when receiving traffic from ciscos. I havnt found any audio problems although I didnt send much traffic. Latest oh323 has some

Christopher- Nothing like defining a complicated environment. I do have some experience in this arena- but unfortunately, not with the OH323 driver- I generally stick to the Nufone driver, as I find it more reliable overall. YMMV. One thing that might help is if you could tell us if it ever worked, or if this is a new problem that's cropped up since a particular change. Still- there are

I am using Nu Fone Network's h323 drivers. I can place H323 calls using following in extensions.conf file, exten => _1732.,1,Dial(H323/${EXTEN}@192.168.1.2) If I need to use h323.conf to do the same I cannot configure h323 to do the same. I get everyone is busy message and I do not see IP packets being generated by * trying to communicate to 192.168.1.2. Can someone point out what I