similar to: legacy Alcatel 4200/4400 and Asterisk (QSIG/PRI) and callerid

Hi all, I'm new in the forum, and although I have some experience in Asterisk, I've never work with Asterisk FXO, FXS, E1... cards. I have several costumers with ATAs working with my SER. However one of them bought an Alcatel PBX OmniPCX Enterprise and now he wants I give him a E1 interface for interconection with its new PBX. I understand I need a E1-IP gateway which could be Asterisk

Hi, Is Asterisk "fully QSIG-compliant"? I currently have an Alcatel 4400 connected to Asterisk 1.2 and 1.4. Zaptel versions are 1.2.26 and 1.4.11. I am using switchtype=euroisdn and all works fine. However, it seems that Alcatel's latest firmware has dropped support for euroisdn which is really despicable. So now I need to see if I can migrate to QSIG which is supported by

Greetings list, I've been asked by someone to help them set up a SIP link between an asterisk system and an Alcatel OmniPCX (v6 software). The asterisk bit's fine, but I know nothing about the Alcatel except that it does apparently allow the setup of SIP trunks. Does anyone have experience with the Alcatel unit? Any obvious pitfalls to watch out for? Any suggestions gratefully

Hi guys, Recentlly i did a asterisk gateway and use it with an alcatel pabx. All is working, i have only two problems. 1. When call incomming to asterisk, it forward to digium card to PABX Alcatel. The user that start the call can't hear the control tone of ring ring ring. Tha calls stay without sound until the called part answer the call. At this point, conversation follow normaly. 2. When

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1.4 libpri and QSIG. So this

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

Morning Asterikians, I've just got my nice shiny quadBRI card, and it seems to be working very well - except for one little issue - CallerID. The card is currently connected to an ISDN2e line in P2P mode, and an S0 adapter on our existing alcatel PBX. The S0 connection recieves callerID and displays it correctly - the 2e line doesn't, and BT have said that CLID was enabled on the

Hi, I followed the how-to from http://www.alcatelunleashed.com/viewtopic.php?f=44&t=840 All works fine except for Asterisk->Alcatel calls. Actually, calls from Asterisk to analog extensions on the Alcatel work. However, calls from Aserisk to digital extensions on the Alcatel 4400 do NOT work. I get this error in the Asterisk log: -- Executing Dial("SIP/4053-0823dd48",

Hi there! I wan't to connect my * to an Alcatel 4400. Does anybody have some experiences with that? I have the problem that I can dial in to *, but not *->A4400 . :-( Thx Marc

Hello list. I'm going te explain my trouble. I have my asterisk with a TDM400P with 4 FXS channels. Two ports are connected to a Panasonic PBX (it's working fine), and others two ports are connected to an Alcatel 4200 PBX (but it doesn't anwer). I connected to a CO port (where i had a pstn line). When I call to the Alcatel PBX, the asterisk show me in it console that es ringing but

Hi, Does anyone have any experience connecting asterisk to alcatel 4200 series pbx with bri cards? Does it should work with asterisk bri in NT mode, and alcatel bri with TE mode? Cheers, Igor Neves.

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

Does anyone have any input into integrating asterisk with a alcatel 4400 PBX. Acording to what i've found is that Alcatel uses R2 for E1 -- regards Vikram (http://www.vicramresearch.com)

I am looking to get the info about QSIG support in Asterisk. Does Asterisk have QSIG support? Does Asterisk support QSIG SIP Tunneling or QSIG SIP Interworking? If so, How to configure that? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060503/3cb7f966/attachment.htm

That was my impression as well, I tried adding switchtype=qsig in zapata.conf, but all I see is the capi information... No connection... Janne > -----Ursprungligt meddelande----- > Fr?n: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] F?r Peter Svensson > Skickat: den 23 februari 2005 21:34 > Till: Asterisk Users Mailing List -

Hello, Does anybody know if Asterisk can support QSIG protocols to be interconnected with a Traditionnal PABX? (Using a HFC chipset based ISDN card to emulate NT Interface) Thank you in advance ;-) Ignace

Hi all, I'm planning on connecting our Asterisk to our legacy PBX (an Avaya INDeX). I was originally going to sit it between our ISDN connection and the INDeX (tried it, worked ok) but now I intend to hang it off a spare PRI card just so should the * fail we keep our ISDN's at the INDeX, yes I've looked at ISDNguard but little info from the manufacturers. Anyhow, I'm now

Hello all, as good? It would like to make a question, asterisk supports the protocol qsig, for interconnections in ISDN with equipment Siemens HiPath 4000 or same Ericsson MD110, so that it could identify to the name and the number of hosts and also to use some features of asterisk in the Siemens/Ericsson equipment. Greetings Josu? -------------- next part -------------- An HTML attachment was

[Reposting, as was bounced for non-member, sorry if this is a dupe] Arrangement: { PSTN }--E1--[PBX]--E1--[*]--LAN--[SIP phones] \__[PBX system phones] Normal calls between PBX system phones and SIP phones work, in both directions. The call logs look like (ignore the no answer, it did ring):

I have been asked by a potential customer whether we can connect an Asterisk box to an Ericsson MD110 that has an E1 port with ISDN-USR. They are unable or unwilling to upgrade their E1 port to QSIG. Has anyone here had experience of successfully making such a connection? I have found a couple of hits on Google that suggest it "should" work, but I'm after something a little more