similar to: Ideal setup for PRI/T1 and TE110P

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

I'm ordering a PRI T1 for use with Asterisk and a Digium Wildcard TE405P. The provider is asking me a number of questions about how I want to configure the line. Here goes: 1. Dial Tone - No, Yes - Precise, Yes - SCC 2. Framing - SF, ESF 3. Line Coding - AMI, B8ZS 4. Signaling Type - Ground Start, E&M, Loop Start w/Ring, Loop Start w/o Ring 5. Pulse Mode - DTMF, MF 6. Outpulse Start -

Hi, I'm seeing rather odd behaviour on a new box with TE110P card. I'm running the TE110P span with ccs,hdb3,crc4 in pri_net, connected to a second machine with a TE410P in pri_cpe. The span is idle. I'm using pri intense debug span 1 and can see the RRs going back and forth. So - things are running along with the span showing "Provisioned, Up, Active" in pri show

Hi, I just got a T1 interface for a AT&T (became Lucent) System75 (uses same cards as Definity). I would take a crack at making a cable but can't determine the pinout for a cable and it is not apparent from the board. Asking you guys makes sense as one of you may have one of these systems. The cable has a amphenol male D50 connector on one end and probably a rj45 on the other. I also

<div><BR>Hello,</div> <div>&nbsp;I bought a TDM400P, and intended to use it with my analog phone, which is RJ11 ofcourse. So, the question now, how do I plug in my RJ11 phone to the TDM400P card, which has an RJ45 interface? Also, since it's an 11B card, I also intend to bring in an analog line into the RJ45, so i am still left with the same question....how do I go

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

This is a really rookie question: when should i use TE110P ISDN PRI Card? -- Necati DEM?R --------------------------------------- -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100621/07d2917f/attachment.htm

Greetings, Our telco called last week, saying that a lot of channels on our PRIs are blocked. And with blocked they have the following description in the Siemens exchanges: BBAC BLOCKED BACKWARD This status is set when the partner exchange has a blocking set and the signaling of the trunk (non-CCS7) is able to report this blocking in the backward direction. This status can

We are in the process of installing a PRI line and we are going to connect it to an Asterisk Box. Verizon called us today to find out some information. I am surprised that they have never heard of Asterisk or Digium. But anyways, they needed some information in order to set up the circuit. Does the TE110P support NI1 or NI2? (I think the answer is both) What is the number of digits

Hey All, AT&T is installing a PRI in a couple weeks and while I've been doing homework on PRI's for the last few weeks there's something I'm still confused about. After being asked how many digits I wanted them to send us (10) was how many digits will you outpulse to us, 4, 7 or 10? I asked her what that meant and all I got was the question repeated. Do any of you have

Hi it's possible to use a Digium TE110P Single T1 / E1 PCI Interface for supply a E1 link to a old PABX ? Thanks

Hi, I have a problem with polarity reverse this my dahdi config [channels] context=default usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1

I can only conclude that Samba is an elaborate hoax and here's why. 1) Setup is more complex than Sendmail (it set the standard for complexity) 2) Even the simplest smb.conf causes trouble 3) You can pass ALL the tests in the DIAGNOSIS procedure, AND Samba will still not let you SHARE FILES or SHARE PRINTERS between Windows and Unix but you WILL be able to BROWSE YOUR SHARES (Just pretend

I'm getting unstable behavior with my newly installed TE110P T1 card. It hangs up any incoming call anywhere from 20 seconds to 6 minutes. Frequently, when you call back on our incoming T1 there'll be an automated announcement (maybe from the telco?) stating "we are unable to complete your call at this time". I simultaeously get a yellow alarm on the system and shortly

Hi all, Muppet from the UK asking for help We are just about to have a T1 line installed in our office in Dallas and "Advantex" the supplier has sent a questionnaire asking a number of questions. I have put the question area at the bottom of the email, we will be using Digium's hardware. could anybody help :-) In the UK when I asked for a E1, number of trunks required and the

brett@websmyths.com wrote: > Also - an outside chance - make sure Tip and Ring > are correct. You could be getting ground loops - depends on the noise. > I am having noise and slip errors between my TE110P and a legacy PBX T1 card. Could this be the same symptom? The connection is made using a 15 pin serial on the T1 Card side to RJ48 on the TE110P side. I can't determine what the

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Hello every body, I ve installed Trixbox 1.2 on "DELL OPTIPLEX GX 240", i upgreded it to the latest version. I've 2 cards installed in the same pci channel via a bridge or plug i don't know exactly what's his name( but a card (1 pci) that gives 2 pci channels) the first card is TDM400P: it's ok the second is TE110P: it's not ok . No led is on neither the red nor the