similar to: h323 channel driver for production

I use asterisk 1.2.5 and h323 that comes with addons 1.2.1. Incoming call comes on h323 trunk. Person A (local SIP phone) receives call and tries to make attendant transfer to person B (local SIP phone). They speak. Then A hangs up. Call form h323 trunk doesn't get to person B. This is what I get on CLI. -- Attempting native bridge of OOH323/xxx.xxx.xxx.xxx-5381 and SIP/307-5663 --

This is third time today that my Asterisk hangs up. It seams that I have problems with h323. I'm using ooh323 from Asterisk add-ons. I have the following configuration Asterisk 1.2.1 Asterisk-addons 1.2.1 Fedora Core 4 I'm using SIP phones and h323 trunk to my VoIP provider Like I said this is third time today that he hang's up. First time, I came at work and Asterisk was down.

First, I'm not sure is this Asterisk or ooh323 channel problem. It seams that I have solved (I do hope so!) deadlock problem with ooh323 (thanks to Sean and his patch). Now I have another one. It seams that some channels stay open even they should not. This is what I see from CLI: pbx*CLI> show channels Channel Location State Application(Data) SIP/302-924a

Does ooh323 from asterisk-addons 1.2.1 support alaw codec? This is what is written in h323.conf.sample that can be found in asterisk-addons dir. The codecs to be used for all clients.Only ulaw and gsm supported as of now. Default - ulaw ONLY ulaw, gsm, g729 and g7231 supported as of now disallow=all allow=gsm allow=ulaw So, it shouldn't support alaw, but I manage to establish calls with

I have running Asterisk 1.2.5 with addons 1.2.1. on Fedora Core 4. I have installed ooh323 from 1.2.1 addons. How to upgrade addons to 1.2.2 version and install new ooh323 driver? Do I need to install addons 1.2.2 if I only need new ooh323 driver? Can I just untar addons, and run "make clean; make; make install" and then execute following cd asterisk-ooh323c ./configure make make

Situation. I call out from SIP phone over h323 trunk and called person decides not to pick up (on mobile phone they press red button - NO - hang-up). Until the called person press the NO button, I can hear ringing. When called person press the button, I don't hear anything. Asterisk waits until timeout and than ends the call. How can I get busy or some other appropriate signal on SIP phone

One simple question. I'm using asterisk 1.2.1, can one agent be defined in more than one group? Example: group=1 ; queue1 agent => 401,401,Tomislav Parcina agent => 402,402,Katarina Ivanisevic agent => 403,403,Sasa Juginovic group=2 ; queue2 agent => 401,401,Tomislav Parcina agent => 402,402,Katarina Ivanisevic agent => 404,404,Marija Bilic agent => 405,405,Ana

How should I upgrade addons form ver. 1.2.1. to 1.2.2.? I'm particularly interested how to upgrade ooh323 channel driver. -- Tomislav Parcina tparcina#lama.hr

In article <1251.165.146.69.140.1144596935.squirrel@www.ecntelecoms.com>, yusuf@ecntelecoms.com says... > Hi, > > I have had the exact same problem last week. I have not yet solved it. > So instead I am using ooh323, but would prefer to use oh323. Can anyone > help? I'm glad that I'm not the only one :)) Hopefully we'll find solution to this problem. --

How to upgrade h323 from Asterisk add-ons (from version 1.2.1 to 1.2.2)? In INSTALL they don't say anything about upgrade... Thank you for your time! -- Tomislav Parcina tparcina#lama.hr

I'm having problem powering Cisco phone's (7940 and 7905) on Linksys SRW224P switch (with PoE functionality). I have tested three phone's, one is working (7905) and two aren't (7905 and 7940). I have plugged all three phones on same switch port with same cable! Do I need to change anything in phone configuration? Is there something wrong with Linksys switch? How can I troubleshoot

Hi list! How to send a call directly to voicemail recording? When I put this exten => 313,n,VoiceMail,u221 Or this exten => 313,n,VoiceMail,b221 In my dial plan, calling person first hears greeting message (busy or unviable). I would like to avoid greeting message (I would play something with Playback application). Is it possible? -- Tomislav Parcina tparcina#lama.hr

How can I send recordings, that I have recorded with One Touch Record, to e-mail address that is defined in voicemail.conf? Thank you for your ideas. -- Tomislav Parcina tparcina#lama.hr

- How to restart the phone? (On 7960 it is *+6+Settings) - How to setup working dtmf? - How to setup hinting? For line is <line button="4"> <featureID>9</featureID> ... For speeddial is <line button="5"> <featureID>2</featureID> <featureLabel>341</featureLabel> <speedDialNumber>341</speedDialNumber> </line>

When agent tries to transfer a phone call (*2 - att transfer) he hangs up. Why? When a phone call isn't from queue then att transfer works fine. In features conf I have *1 for recording, *2 for att transfer and #1 for blind. In queue blind transfer works. For disconnect I have #0. I guess that * is somewhere defined as for hang-up the call, but where? I can't find it anywhere. Any help

I have several Cisco 79xx phones (7905, 7920, 7940, 7960, 7970, ATA 186) and I need to buy firmware for them. I have contacted http://www.cdw.com and http://www.insight.com/ but they didn't respond. Can anybody tell me where can I buy SCCP and SIP firmware for my phones? BTW, I'm in Croatia (Hrvatska). I heard that location does matter. P.S. My local Cisco reseller wants to sell me

I have tried to use native music on hold. In dir /var/lib/asterisk/moh-native/ I have some wav files (with 755 permission). In musiconhold.conf I have [native] mode=files directory=/var/lib/asterisk/moh-native And in sip.conf I have musicclass=native When I put call on hold this is what I get at CLI. -- Executing Dial("SIP/341-5931", "SIP/344|20|wWtT") in new stack

Hi group. I have huge problem. My pickup exten #8 isn't working. This is what I have configured. pbx*CLI> show features Builtin Feature Default Current --------------- ------- ------- Pickup *8 #8 In sip.conf I have callgroup=2 pickupgroup=2 For called party and same for person that is trying to pick up the call. The person that is trying

In article <02a201c64f16$7376fb10$0201000a@JACK>, balgaa@micom.mn says... > Hello, > > I installed Asterisk from CVS on Redhat Linux 9 and working with chan_h323 module and g729/g723 free codecs too. Can you send us more information about this free g729 codecs? -- Tomislav Parcina tparcina#lama.hr

Hi group! I have been using asterisk 1.2 for quite some time and now I need to go back on asterisk 1.0 (because of oh323 channel driver). One thing that I can't remember is does asterisk 1.0 support native music on hold? If it does, how can achieve it, because it doesn't work the same way as it does on asterisk 1.2. Thank you for your help. -- Tomislav Parcina tparcina#lama.hr