similar to: DISA & SPA3000 issues

We are using DISA with local SIP users. The user enters in a 2 digit code then they get a dialtone and the phone dials out. The problem is that the calls waits 10 seconds after the outgoing number is dialed, no matter what I put for the timeout values. Anyone else using DISA that has run into this? exten => _2X,1,Answer exten => _2X,2,DigitTimeout(2) exten =>

Hi, I have just setup a DISA setup whereby people can dial in, authenticate, are given a dialtone and can then call out. Everything works however there is a 10 second delay after the user enters the number and presses #, until the system does anything. Here is the relevant section from my extensions.conf: -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Folks, I'm trying to test out Asterisk overall. I'm having some problems with DTMF. Currently I'm playing with DISA, but I'm worried this will happen when I get to implementing AAs etc. I have a free SIP trunk from IPKall that I'm trying to make work. I'm able to receive calls, and I've now setup and extension with DISA and a password. I connect ok from the

I can dial from an asterisk host to another one via FreeWorldDialup, on the other side DISA service answer to me and i can ear dialtone. But i cannot send DTMF and dial an extension on the DISA enabled asterisk.....i've tried rfc2833 and inband...but nothing....any tips ??? Thanks, -- Igor Barsanti GPG Public key available at http://pgp.mit.edu

Hi everybody, I am having DTMF detection problem on DISA with my callback system. For many users, it keeps playing the dialtone even after they have input their number. I have trunk setup to both g729 and ulaw. What could be the reason for this problem. Some users have to dial a few times before the system can recognize their dialed number. -- Zeeshan A Zakaria -------------- next part

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

Hi, all I am trying to figure out how to forward incoming PSTN call on SPA3000 to VoIP extension(s). Basically, I have converted my home to VoIP. I have normal phone (connected to SPA3000) and couple of IP phones. All call coming from VoIP DID do ring all phones (analogue via SPA3000 and IP ones). Now I need to do same thing for incoming PSTN calls. I have enabled gateway function in SPA3000 and

I've commited changes to Voicemail2: * Handle properly when being left a message while checking VM -- this should fix the "saving to your inbox" issue too, at least in principle. And to DISA: * Properly handle extensions with multiple matches and "dots" Please let me know on or off list about any feedback you have regarding these changes. Mark

Hi all, Can anybody explain what these values exactly mean. As you all know its the dialtone value on an SPA3000 of linksys. 350@-19,440@-19;10(*/0/1+2). Can anybody help me how to write this code for a dialtone of frequency 425 which is continous. Thanks Dan -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi ! Did anyone had issues/managed to solve issues with DISA over Zap channels on * 1.0.X (STABLE) ? I have a situatuion where DTMFs that should be recognized in DISA work over SIP channels and do not work over ZAP channels (Zap channels are on TE110P) I have in default context: exten=> 299,1,DISA(no-password|default) and I have SIP extension 200 in [default] and I have Zap trunk which

I'd like to write a snippet of dialtone that plays dialtone and collects a specific number of digits into a variable. Sort of like READ but with a generated dialtone. Naturally, I want the dialtone to stop playing after the first digit. I can't find this anywhere. Only thing I can think of is a no-password DISA. Is this the correct method? Is there a better one? </edg>

Deutsche ?bersetzung folgt / German version following ===================================================== Hello, i have Asterisk running with 2 ISDN-Cards. One AVM Fritz for connection to german ISDN and one HFC-compatible-Card (NT mode) for connection to ISDN-Phone (later: ISDN-PBX). Here is my actual installation: ISDN -> Fritz - ASTERISK ? HFC-NT <- ISDN-Telephone If i pick up my

Is there any known reason that the DISA() routine should behave differently than WaitExten() as far as recognizing DTMF tones? If not, I suspect there's a bug here. Try it yourself--two DID's on our PRI, numbers below let you test each routine: It is my observation that some setups/phones DO and some DO NOT express this variance. --I could not show any variance on a sprint mobile phone

I would like the ability for a sipura sip device to instantly connect to an asterisk server as soon as the sipura sip device goes offhook and before any digits are pressed. This way asterisk can provide the dialtone and the dialplan. This also allows me to play a greeting to the phone before giving them a dialtone. Is there any way to do this, like possibly having the sipura device dial a

I am a little green when it comes to all this but I am trying to connect our PBX to an asterisk server using a TDM400 with 4 FXO modules. I am able to dial an extension on my PBX handset and I get a dialtone from the PBX. After 2 rings I then hear the asterisk server connect and I get a dialtone from asterisk. I am then able to dial an extension on another asterisk server. My question is: How do

In my seemingly endless search for the cause of echo on my SPA3000, I wired it up in the following configuration: Analogue Handset <--> (FXS)SPA3000(FXO) <--> PAP2 And set the Line1 dialplan on the SPA3k to '(<:@gw0>S0)' which means that as soon as I pick up the handset I get linked straight through to the PAP2, which gives me dialtone. Even in this configuration, with

I am trying to integrate a Nortel Norstar system with an Asterisk service using a TDM04B card (4 fxo). So far everyting works from Asterisk to Nortel. The problem is when someone dials from the Nortel PBX to the Asterisk server. Asterisk answers the call and provides a dialtone (with DISA) but appartently the DTMF tones are not passed to asterisk and the call cannot proceed. This only

Hi, I have two asterisks connected via IAX2 trunk. The first * use dial prefix 2XX, the second one 3XX. Calls routing works OK. But I don't know how to get dialtone of remote asterisk pbx. I'd like to get dialtone of asterisk #2 after dialing 3 and dialtone of asterisk #1 after dialing 2. I know something about DISA but I'm not sure if it is a right way. Can you give me advice?

Greetings Asterisk users! I'm trying to setup Asterisk system to act as a callback system together with callcentric (http://callcentric.com) but it appears that I hit common DTMF issue and I want to workaround this problem. Basically my current setup is the following: 1) I have dedicated Asterisk server that it is linked to my callcentric account 2) I have US phone number (DID) from

I am still haveing problems (echo) with my X100P but I'm thinking it has more to do with the server it is in which is not a negotiable item at this time. My question then is to the use of SPA3000's as a replacement from the FXO standpoint. 1. Can you setup the FXO port to recognize distinctinve ring and call a different context like you can do with Zap channels? Being able to call a