similar to: digium certification for Europe

Does anyone know of a way to simulate the signaling of a PRI trunk for testing/setup purposes? I realize this may be a rather naive question, but I was wondering if you could take a TE110, for example, and using a crossover cable (or not?) and some means of emulating the NI2 signaling protocol connect it to another TE110 on another machine to test and verify an installation before the telco

Hello, I'm looking for IP phones with at least 10 or so speed dial buttons. Can you recommend something which works with Asterisk and does not cost fortune? An option can be analog phone combined with ATA adapter. So hints for good analog phones (EU) are welcomed as well. Thank you, -- David -------------- next part -------------- An HTML attachment was scrubbed... URL:

I just wanted to see if any one else has seen this or could help point me in the right direction on this problem. I have a TE411P card in my * box. I am running FC4 x86_64. I used to have two TE110 cards in the same box that worked without any problems. Since changing to the TE411P cards, I am getting random DTMF tones being produced on a bridged connection through the same Channel Bank that I

Hi, I just read a pressrelease from VON that Digium will soon be releaseing a couple of new cards. What got me interested was: "The TE420P and TE415P support 128ms of G.168 (2002)-compliant echo cancellation across their entire 128 channels." Does anyone know when thease will be released and what they will cost when released? Thanks!

Hey, I'm up and running fine with 30 Polycom 500s connected to Asterisk 1.2Beta on Cent OS 4.1 with a Digium TE110 connected to a PRI line. Nearly every hour, almost on the hour I get this: Sep 29 23:01:38 VERBOSE[3567] logger.c: -- B-channel 0/1 successfully restarted on span 1 Sep 29 23:01:38 VERBOSE[3567] logger.c: -- B-channel 0/2 successfully restarted on span 1 Sep 29

Hi, Is there a simply way to allow dialout from ISDN modem to outside number through Asterisk? I've got an server with an Asterisk and the following cards: 1. TE110 -- to telco 2. TE400P with one FXS to analog phone 3. Two HFC-S based cards in NT mode I'd like to connect ISDN modem to one HFC-S card and allow dialout through TE100 to some external number (being more precisely, to some

Hi I've bought the Wildcard TE110 some days ago but I'm unable to get it to work with Siemens HiCom 300. I've tried this so far: 1. I've used standard cat5 cable cut off on one edge and twisted wires 1 to 4 and 2 to 3 which is according to cisco a short circuit for E1 lines. Wildcard takes a few seconds and sets the link to green (OK). 2. I've tried to connect our running

Hello, I am looking for a way to control another legacy PBX from Asterisk using a CTI interface. Are you aware of any legacy PBX CTI control card that can be controlled by Asterisk? I have an Avaya PBX with CTI interface and researching if I can connect Asterisk to this. :-) Thanks for any hints. -- - David Hajek Daktela - VoipObchod http://www.daktela.com/ http://www.voipobchod.cz/shop/

OK I have been battling with echo problems with asterisk on ISDN for a few weeks now, and still can't solve it (although I think I have tried everything I can find.) I will try a post everything I think is possibly relevant that I can remember with the hope someone can point me in the right direction. current spec I am using (Trixbox 1.0 was still in beta at the time an didn't detect

Hi- I'm using IAX between two boxes, where one box is located in US and the second in Europe. I'm trying to achieve the best voice quality and mainly reliability between these boxes and looking for hints and experience of others. Facts: - Asterisk 1.0.7 - RTT varies from 130-170 ms, depends on time and actual Internet throughput Questions: - What is the sugested codec for such setup?

what happens when you drop your gains? use /etc/asterisk/zaptel.conf and fiddle with tx and rx values. Works, most of the time. -----Original Message----- From: John McEntee [mailto:john@mcentee87.freeserve.co.uk] Sent: Wednesday, October 11, 2006 12:25 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [asterisk-users] Echo problems on ISDN. (mainly incoming calls) OK I

Hi, I found some issues with Snom 320 message retrieve key. This button works only when the MWI does not blink! If MWI blinks and I do press retrieve button I get "Unknown" on display and busy tone. From the sip debug it looks like that Snom does not send credentials to Asterisk which responds with 407 Proxy Auth required. I have loaded Snom with latest 5 firmware. No change. I'm

Hi, during gradual migration to Asterisk, I put Asterisk in front of a legacy Alcatel PBX: PRI PSTN <--> Asterisk <--> E1 cable <--> Alcatel PBX After successful deployment of VoIP phones, it's time to drop Alcatel PBX! I'd like to keep some of analog lines to support modem, fax and some older stuff. What's the best choice? A channel bank or a TDM2400P card? Can I

Hi All; How to let the virualbox (ubuntu OS) to be able to see the digium card? Because when I install elastix or asterisk with dahdi, it is not able to see the digium card if the installation though the virualbox .. What is the solution? Regards Bilal

Hi, I have a box with Debian Sarge, Asterisk 1.2.1 (and zaptel 1.2.1) and a TDM2400P with echo canceller. I installed the card but no echo cancellation is being made...seems like the echo canceller module does not work, infact the software cancellation is working. My zapata.conf has echocancel = 128 and echocancelwhenbridged = yes but no echotraining parameter which gives a warning. I found

Hi i have a tdm2400p and installed asterisk 1.4.11 with zaptel 1.4.5 im having an error message when in running asterisk with the tdm card in. here's the error from the console of asterisk: [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:7489 mkintf: Unable to get span status: Inappropriate ioctl for device [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:10466 build_channels: Unable to register channel

Hello, is it possible Asterisk's ChangeLog will contain a reference to appropriate bug number in bugzilla? This can be very handy. Thanks, David

Hi, I'd like to change 3 TDM400p with one TDM2400p to avoid echo (my intention is to use a TDM2400P echo cancel module). It TDM2400p working good with asterisk 1.2.1? Or I need to install a new asterisk version? TIA Giorgio Incantalupo

Hi, what new Dell servers are compatible and KNOWN to work with Digium TDM cards? I've looked at Digium's compatibility list at http://www.digium.com/index.php?menu=compatibility. Does this mean that other Dell servers like SC1420, SC1425, 800, 1800 are working just fine with TDM cards? Can someone clarify this? Thanks -David

Hello, I`ve got a problem which I can`t deal with. I own 2 cards - TDM2400P and TE410P. I`ve put them into a HP Proliant DL380 G4 server, compiled the drivers according to the manual. Unfortunetly there are both cards channels are configured in zaptel.conf file the first module (in this file) sends an error. For configuration: span = 1, 1, 0, ccs, hdb3, crc4 fxsks = 21-24 bchan = 25-39,