similar to: OT: Polycom BootRom 3.1.3 and vsftpd 2.0.3

Hello everyone, Please forgive the exclamation points but I have been battling this one off and on for about four days now. Sorry for the cross post. It all started with a box of IP 501s. I contacted my reseller and obtained the latest BootRom and SIP firmware. Unzipped, configured, copied over to my FTP server (running AstLinux, of course). The phone booted, so far so good. Updated

From what I know this log show everything working Perfect. Then it goes to the Welcome screen then after a long time of processing, it errors out with a 0x10000 error Any Ideas? 1005195711|so |4|00|---------- Initial log entry ---------- 1005195711|so |4|00|+++ Note that bootrom log times are in GMT +++ 1005195711|hw |4|00|Initial log entry. 1005195711|wdog |4|00|Initial log entry

Received two new Polycom 500 phones. Dhcp and ftp configured properly to load the various files including v2.5.0 bootrom.ld, etc. One of the phones loaded all firmware and config files properly, registers with *, and is usable. The second phone loads bootrom.ld (from the same ftp server on the same wire as the phone), but towards the end of the bootrom.ld load process (about 430 pkts as seen by

I'm having problems updating my bootrom to the latest (3.2.2) version. Basically, my phone starts downloading the bootrom, but I am completely certain that it doesn't actually complete the process. It gives me an "error updating bootROM!" message, but it only takes about 2 seconds to complete the download (which, because of my WAN link and FTP server environnement I know is

I was progressively upgrading this phone from 3.1.2 to 3.2.3, then to 4.0.0. v3.2.3 worked fine, but when I went to 4.0.0 (Even adding the more specific 2345-11500-040.bootrom.ld), it won't run, and just keeps rebooting. Now I've got a really nice doorstop unless someone knows how to get out of this predicament. Help! 0925003705|cfg |3|00|Beginning to provision phone 0925003705|dns

...even when I do the "factory reset" (4-6-8-* then 456). I tried using FTP and TFTP, but even though the phone uploads the log, I get these errors: 0927211350|app1 |3|00|Time has been set from 0.us.pool.ntp.org(69.60.124.59). 0927211350|cfg |4|00|Could not get all 512 bytes of the header. 0927211351|cfg |4|00|Could not get all 512 bytes of the header. 0927211422|app1 |4|00|Loaded

I've had an IP300 for a while now and it's been working fine. I just got an IP500 and when it connects to the FTP server it downloads the new bootrom and says error loading. The bootrom is fine and works on the 300... In addition, I downloaded a new copy to be sure and it still doesn't work. Can anyone give me some advice?

Hey all, Just getting started playing around with my Polycom 600. According to the wiki, it looks like it's recommended to run BootRom 2.6.1 and SIP 1.4.1. Is that info still current, or is it safe to upgrade to 3.0.1 and 1.5.2? Justin --

When I bought two Polycom 501 SIP phones, I naively thought they were Power-over-Ethernet (IEEE 802.3af) because they were "powered over ethernet." Silly me. Polycom must have some odd voltage or funny way of injecting the power, because the POE switch I bought for them (Netgear F@510P) won't power them, though if I use the Polycom-supplied AC adapter and ethernet power

Hi, I have a Polycom 501 that is currently unusable because I started a firmware and sip upgrade that I can't complete. The Ubuntu box address is set static at: 192.168.1.101. The phone address is set static at 192.168.1.51. The phone settings for the server menu are: Server Type: Trivial FTP Server Address: 192.168.1.101 Server User: PlcmSpIp Server Password: PlcmSpIp (not sure what it

James Cass wrote: > I picked up a cheap JS200-FX on ebay: http://x100p.com/products/js200fx.php for $30, and it works great for a home install. Very low power draw as well. > > James Cass <http://goog_987864563> > jcass78 at gmail.com <mailto:jcass78 at gmail.com> The JS-200 runs a very old ( 1.4 ) version of Asterisk I have set up more than 30 nodes using the HP thin

i recently bought an SP4000 conference phone but having problem provisioning it using ftp, every time it just hangs at "Updating initial configuration..." screen. when i switch it to tftp, it'll work fine. i though it was bootrom/firmware issue so i upgrade it to bootrom 3.2.2/sip 2.0.1 but it makes no difference. any thoughts? p.s. i'm using debian sarge proftpd 1.2.10 and the

I`m trying to provision my Polycom 501s using Pure-FTP. Everything has been working fine, until I put a new bootlog.ld file. Sniffing the packets between my phone and the FTP server during transfer, I noticed that the file is not 100% sent (it seems to send about a third of it, and then the phone wisely detects it as being corrupted and reboots). I have suceeded in using other FTP clients to

Hi All, Please feel free to correct any misconceptions in my premises as I get to my question. I have about 6 ftp services running on a CentOS system that is going down for service, and I want to move the ftp services to a VM on another network. These are all running on Proftpd, with fairly complicated directory/permissions/rate control layouts, as proftpd nicely supports. First, it appears

Hello everyone, I was just looking over some logs, and it appears that there have been less than 3,000 downloads for my native Asterisk sounds packages (all formats combined). What gives ;)? In my humble opinion, EVERYONE (unless you have your own in a different voice/language) that uses Asterisk should be using these prompts. How about a direct link this time:

The AstLinux Team has released 1.2.0. All current users are encouraged to upgrade as this release addresses the bash "ShellShock" bug. New in 1.2.0: * New Linux Kernel 3.2.x * "igb" ethernet driver for Intel Atom C2000 * Enable AES-NI support * New "sip-user-agent" firewall plugin * New versions of Asterisk 11 and 1.8 * Bash "ShellShock" security fixes A

I got em. You want em? Anyone know how I can get these to the site listed on the Wiki? Thanks, Wiley -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050512/dfee13b3/attachment.htm

Hello Everyone, I have released AstLinux 0.2.2. There are way too many improvements to list here, but here is a short summary: Linux 2.4.27, iptables, mini_httpd (with PHP & SSL), phpconfig, AstShape traffic shaping, tftp server, OpenSSH, proftpd, Soekris Net4801 and Pentium-MMX and higher x86 support. There is actually WAY more software, but I couldn't possibly list it all. It

Hi all, I'm sure this is a quick fix, but I've not found the answer yet. On a fresh install of CentOS5, I need to use an alternate port for ftp. Currently vsftpd wants the standard port which is in use by another system on my NATted network. So...how does one go about reconfiguring vsftpd to do this? I've looked in /etc/vsftpd/vsftpd.conf to no avail. In my Slackware days,

Hi! I'm trying to figure out what's going wrong with a "simple" FTPS setup and VSFTPD. I saw references on Google and tried, and tried, and tried... without success. I'll start by explaining my situation: I have a WEB development server behind a firewall. It's currently only for the intranet. We now have an external company that will have to do a new website