similar to: OT: Polycom BootRom 3.1.3 and vsftpd 2.0.3 WARNING!!!

Docs? Polycom has docs? Where would one find this fabled land of... err I mean Polycom does stating what ftp servers are supported? Doug. -----Original Message----- From: Ken D'Ambrosio [mailto:ken@jots.org] Sent: Tuesday, March 07, 2006 12:12 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re:

Received two new Polycom 500 phones. Dhcp and ftp configured properly to load the various files including v2.5.0 bootrom.ld, etc. One of the phones loaded all firmware and config files properly, registers with *, and is usable. The second phone loads bootrom.ld (from the same ftp server on the same wire as the phone), but towards the end of the bootrom.ld load process (about 430 pkts as seen by

I'm having problems updating my bootrom to the latest (3.2.2) version. Basically, my phone starts downloading the bootrom, but I am completely certain that it doesn't actually complete the process. It gives me an "error updating bootROM!" message, but it only takes about 2 seconds to complete the download (which, because of my WAN link and FTP server environnement I know is

Hey all, Just getting started playing around with my Polycom 600. According to the wiki, it looks like it's recommended to run BootRom 2.6.1 and SIP 1.4.1. Is that info still current, or is it safe to upgrade to 3.0.1 and 1.5.2? Justin --

I have been struggling over central provisioning for quite some time. I have eagerly watched each post with like problems but have yet to find a reliable answer. I have a Polycom 501 and I am trying to provision from an FTP server, and just to take any routing out of the issue it is on the same subnet. I am running the 2.0.1.0291 firmware and 3.2.2 bootrom. I set the IP info on the phone and

I was progressively upgrading this phone from 3.1.2 to 3.2.3, then to 4.0.0. v3.2.3 worked fine, but when I went to 4.0.0 (Even adding the more specific 2345-11500-040.bootrom.ld), it won't run, and just keeps rebooting. Now I've got a really nice doorstop unless someone knows how to get out of this predicament. Help! 0925003705|cfg |3|00|Beginning to provision phone 0925003705|dns

...even when I do the "factory reset" (4-6-8-* then 456). I tried using FTP and TFTP, but even though the phone uploads the log, I get these errors: 0927211350|app1 |3|00|Time has been set from 0.us.pool.ntp.org(69.60.124.59). 0927211350|cfg |4|00|Could not get all 512 bytes of the header. 0927211351|cfg |4|00|Could not get all 512 bytes of the header. 0927211422|app1 |4|00|Loaded

From what I know this log show everything working Perfect. Then it goes to the Welcome screen then after a long time of processing, it errors out with a 0x10000 error Any Ideas? 1005195711|so |4|00|---------- Initial log entry ---------- 1005195711|so |4|00|+++ Note that bootrom log times are in GMT +++ 1005195711|hw |4|00|Initial log entry. 1005195711|wdog |4|00|Initial log entry

I've had an IP300 for a while now and it's been working fine. I just got an IP500 and when it connects to the FTP server it downloads the new bootrom and says error loading. The bootrom is fine and works on the 300... In addition, I downloaded a new copy to be sure and it still doesn't work. Can anyone give me some advice?

I have 1 Centos server V4.x already running VSFTPD and when the user logs in they get chrooted to the home directory, I have installed the same config files to a second server (again Centos V4.x) and have setup the same user on the second server but the user does not get chrooted to the home directory but is placed in /var/ftp/pub and cannot upload file. The files I copied are:-

My vsftpd was working. I use it configured via xinetd and turn it off (disabled = yes) when I'm not using it to keep the bad guys from hammering on it. Recently I upgraded to 4.2 (via yum update). That' the only change I know of on the system. And I didn't have any problems with it. Today when I try to ftp, i enabled it in xinetd.d (with disable = no and a "service

greetings today i was expanding my knowledge of vsftpd on a low traffic CentOS 4 production environment server i have fyi, i was working on learning to setup a chroot environment by the simple editing of /etc/vsftpd/vsftpd.conf so, as i normally do when i start making changes i did this cd /etc/vsftpd/ cp -a vsftpd.conf bak-vsftpd.conf then i made the edits in /etc/vsftpd/vsftpd.conf that i

I have an up-to-date CentOS 6 with reasonable amount of ftp activity (a dozen of network cameras uploading images every second 24x7). The first issue was that the whole /var filesystem was about to get full, because of huge ftp daemon log. vsftpd.conf says: # You may override where the log file goes if you like. The default is shown # below. xferlog_file=/var/log/vsftpd.log Ok, the above

Hi folks, I can't seem to log into my system via vsftpd. All other services using PAM are fine...Am I missing something simple? ftp> user (username) user 331 Please specify the password. Password: 530 Login incorrect. # getenforce Permissive here is the event in /var/log/audit/audit.log: type=USER_AUTH msg=audit(1247235151.569:9781): user pid=21052 uid=0 auid=0

Hi ALL I'm using vsftpd as FTP server, and I'd like to chroot my FTP users to their home dir. How can I do it? i.e. "jailing" them in their home dir... at the moment I have the following issues the user when they login to ftp server they go to the main directory /var/ftp/ /etc/passwd ... sdc:x:501:501::/var/ftp/sdc:/bin/bash ase:x:502:501::/var/ftp/ase:/bin/bash

Hi, This update is for the HowTo at http://wiki.centos.org/HowTos/Chroot_Vsftpd_with_non-system_users Regarding two of the scripts provided: vsftpd_virtual_config.sh and vsftpd_virtual_config_withTLS.sh: The configuration additions it makes to PAM do not work on 64-bit systems. In vsftpd_virtual_config.sh (Lines 55 & 56) and vsftpd_virtual_config_withTLS.sh (Lines 123 & 124) should be

The proposed subject of Wiki contribution: Chroot vsftpd with non-system users The proposed location of Wiki contribution: http://wiki.centos.org/HowTos/Chroot_Vsftpd_with_non-system_users I propose this Wiki to give user choice that they can select whether virtual users and system account coexist in vsftpd system. The shell file vsftpd_virtual_config.sh should also adjust to make this function

Greets ... I am not getting it. I have samba (old one, 3.0.22-11-SUSE-CODE10) in an ADS-context, winbind works OK ... I am trying to connect vsftpd to winbind via PAM, this works TOO GOOD ;-) currently I am able to login to vsftpd with ANY password, that's bad. I am not understanding that PAM-stuff and I have some pressure to get that ftp-server up, so please would someone help me out? My

Hello I hope I finally made the changes right for my contribution to Wiki How To. My Wiki username is now : ThomasLibnsek and the HowTo is located at http://centosforserver.blogspot.com/2010/02/virtual-hosting-with-vsftpd-and-mysql.html I 've added some - explanations: why do you want to store users in MySQL? Why should youchoose a different password for mysql's root account than

I've got a problem with vsftpd on a new CentOS system. Most users can login and list and everything but when they want to transfer files the client says "transfer failed" or so. However, it works fine with two users. Of course, these two have been created by me and used only by me. So, I didn't detect the problem before other users tried to upload. I tried with the command