similar to: Oh this is bad.... bindaddr and rtp traffic

Has anyone got any neat solutions for Asterisk .conf file revision control? We have multiple Asterisk boxes here, that we'd like to maintain a _mostly_ common set of conf files on. They aren't all the same though. There's subtle differences. For example, in sip.conf, iax.conf etc, the bindaddr setting is different. Dundi.conf is very different between each system. At the moment I

Hi to everybody, My IAX is not working, When I type reload IAX it returns me: AsteriskSlave*CLI> iax2 reload == Parsing '/etc/asterisk/iax.conf': Found == Parsing '/etc/asterisk/users.conf': Found [Aug 26 10:05:04] NOTICE[18078]: chan_iax2.c:13546 set_config: Ignoring bindport on reload [Aug 26 10:05:04] NOTICE[18078]: chan_iax2.c:13610 set_config: Ignoring bindaddr on

hI, Trying to understand how to setup two PRIs in sip.conf. Using Asterisk 1.4.23. I have a provider giving me two PRI (different rate centers) through SIP. Both PRI comes in from the same IP on the provider side, but go to two different IPs (both on the same box) on my side. How can I setup two different SIP peer, one for each of the PRIs I get, if all I can use to differenciate them

Well, this is a major pain in the ass. I got realtime static working for sip.conf. 'Great!' I thought. That was until I realised I couldn't use it. Our Asterisk systems are using OSPF and listen on interface lo:1. Asterisk doesn't like to use an interface name for it's bindaddr setting, so you have to put the IP address of lo:1 in there. If you put in 0.0.0.0, it seems to

I'm running CVS HEAD. The last time I updated was January 7th, at which time everything was fine. Having updated again today, January 17th, I'm having problems with IAX2. I use the "bindaddr" directive for both SIP and IAX2, and while SIP respects it, IAX2 doesn't. It listens on every interface, and uses every one of them for outgoing source addresses. This breaks IAX2

Dear All, I have a data frame of vectors of publication names such as 'pub': pub1 <- c('Brown DK, Santos R, Rome DF, Don Juan X') pub2 <- c('Benigni D') pub3 <- c('Arstra SD, Van den Hoops DD, lamarque D') pub <- rbind(pub1, pub2, pub3) I would like to construct a dataframe with only author's last name and each last name in columns and the

I have a laptop and desktop that have most of home directory data sync'd, but I am having trouble keeping symlinks straight. On the desktop, my data is separate from the $HOME folder... $HOME = /remote/home/desktop/ and the data is at /data/. Within /data/, I have several directories that are inter-related... eg, /data/pub1/figs is a link pointing to /data/imgs/pub1. It makes life easier

Hmmm. Not having much luck with this. I'm trying to call the DUNDILOOKUP function and assign it to a variable in an AGI script. I've tried setting with EXEC CMD and with SET VARIABLE. In both cases, it's treating DUNDILOOKUP literally, rather than calling a funciton. I've tried this: EXEC "Set" "DIALPATH=${DUNDILOOKUP(2944093|180net)}" and also: SET VARIABLE

Hi all, is it possible to bind SIP protokol not to all but to more that one interfaces. I did try use bindaddr, but i don't know right syntax. Could anyone help me. Thanks, Bob.

Oh! In that case ignore it. Asterisk won't rebind the adapter if you've only changed parameters. The message is misleading -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Vitor Mazuco Sent: Monday, August 29, 2016 10:41 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re:

I just see warning? 2016-08-29 11:30 GMT-03:00, Telium Technical Support <support at telium.ca>: > This shows that asterisk's IAX is already bound to all adapters - so that's > good. Symptomatically does your IAX stop working? Or do you just see a > warning? > > -----Original Message----- > From: asterisk-users-bounces at lists.digium.com >

Folks, When I have a dial string like this: Dial(SIP/3254101&SIP/3254102,20,tr) and I want to check the ${DIALSTATUS} variable after the dial, how do I know which number I am getting the variable for? And, what about this? Dial(SIP/3254101&SIP/3254102@proxy1,20,tr) What happens in that case? How can I get the ${DIALSTATUS} variable for EACH NUMBER dialled? Thanks, Doug.

Hi, see the log below root at AsteriskSlave:~# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: p3p1: <BROADCAST,MULTICAST> mtu

I have this in sip.conf: [general] context=default allowoverlap=no bindport=5060 bindaddr=0.0.0.0 srvlookup=yes progressinband=yes [19256002182] type=friend username=19256002182 callerid="Test hone 1" <+19256002182> host=dynamic canreinvite=no secret=password context=test disallow=all allow=g729 [level3] type=peer host=xxx.yyy.16.99 context=default

Hi list, I'm with a little problem on codec negotiation between a cisco827 and asterisk. My sip.conf is like that: [general] port = 5060 bindaddr = 0.0.0.0 context = default amaflags = default allow=g729 allow=gsm allow=alaw allow=ulaw ;disallow=all and cisco like that: dial-peer voice 6 voip destination-pattern 0T session protocol sipv2 session target ipv4:<asterisk-ip>

A non-text attachment was scrubbed... Name: not available Type: text Size: 823 bytes Desc: not available Url : http://lists.samba.org/archive/samba/attachments/19971208/a20d18c1/attachment.bat

This is a list of issues for discussion for CentOS-4. Most of it is based on my experience from building/maintaining CentOS-2 and observing CentOS-3. I have not seen the CentOS-4 beta yet so I don't know if any of this is already done. If these have been discussed on IRC then perhaps someone could produce a shot summary of the outcomes....? * Just call it CentOS-4 not 4.1 etc. Too

Anyone know how to obtain firmware and starter .cfg files for Polycom phones? Despite registering at the Polycom web site, I can't locate this stuff.

So, I'm trying to get the Asterisk vxml (from i6net) working. Having no luck with it. My dial plan has: exten => _X.,1,Answer() exten => _X.,n,Wait(1) exten => _X.,n,Vxml(file:///tmp/menu.vxml) The /tmp/menu.vxml file has: <?xml version="1.0"?> <vxml version="1.0"> <form> <block><audio

> -----Original Message----- > From: Robert Webb [mailto:rwebb@ropeguru.com] > Sent: Saturday, March 05, 2005 5:24 PM > To: 'Asterisk Users Mailing List - Non-Commercial > Discussion'; 'leandro_tenorio' > Subject: RE: [Asterisk-Users] IAX2 (Variables) > > > > > -----Original Message----- > > From: asterisk-users-bounces@lists.digium.com