similar to: NEWS: SIP Firmware Available for Cisco 7970

Hi! I did manage to load phone with SIP image : SIP70.8-0-3S, made SEP-MAC.cnf.xml, but phone never read the configuration from it. On the screen it's written "Unprovisioned", and phone is not trying to register with asterisk. Please help!! MihaelaMJ -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello all, I've got myself into a bizzare situation that I can't seem to get myself out of... Was wondering if anyone had some advice that might get me 'over the hill' on this... Some background: PBX consists of an Asterisk box (running TrixBox), 4 Cisco 7960's, 2 Polycom IP500's, and now an additional Cisco 7960. The phones are all on a separate LAN. There is

Hi, I'm trying to connect Asterisk 1.4 and Cisco CallManager 5 using SIP Trunk without MTP (media termination point). Howerver, Cisco 79xx phones do not support RFC2833, they always notify CCM5 via SKINNY channel no matter where they send RTP to. For non-MTP trunk there's Out-of-band DTMF support in CCM5 called "kpml". I wonder if Asterisk can support it. I found an

Anyone have the 7970 xml config for sip yet? Aaron

Hi All, I upgraded 7970 from SCCP to SIP. But the phone isn't registering. Have you got any working XML file for 7970 phones. Thanks..

Hello; I am facing a problem to let Cisco IP Phone 7942G register on Asterisk. The firmware has been downloaded from the TFTP successfully and currently I am running this load SIP42.9-3-1SR2-1S* I feel that there is a problem in the SEPMAC.cnf.xml but really I do not know which one to be used exactly. Basically, there is some effect that appears on the Phone (for example, it is appearing the

Anyone have experience with the 3-08-2 release of Cisco's SIP firmware? Are there any new features in the SIPDefault.cnf? Thanks, Ron

Hi, I am upgrading a Cisco 7960 phone from SIP V.5.1 to 6.0 and then will to go up to 7.5 However in my first attempt to go from V.5.1 to 6.0 this is hat happens: - The phone reboots - The phone then reads the file OS79XX.TXT from the TFP server. In the file I added the version "P0S3-06-0-00" - It starts upgrading firmware - Then I get the following message: (Upgrade Failed -

Hi all, i have a problem with some cisco 7960. Yesterday i did a firmware-upgrade from 3.1 (1.2) with P0S30203.bin as described in the most documents. Now i get the message Phone unprovisioned and in TFTP-Log i find the following line: 07.03.2005 19:58 :Timeout error sending P0S3-07-3-00.bin to 192.168.0.83, 0 bytes So i think it now wants to load the file P0S3-07-3-00.bin. But i have not

I know this isn't a specifically asterisk question, but does anyone know how to make the phone NOT use it's old config? I'm trying to get rid of the second line registration crap and it's not working. Aaron

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031207/e5e9b8eb/attachment.htm -------------- next part -------------- Hello all, I am newbie to Telephony world (IP and PSTN). Please excuse me if you find my questions very dumb. I am trying to configure my IP 7940 with the Asterisk, when phone boots up it only shows the message "Phone

Folks, I have CISCO 7940g phone. I have in the past configured the phone with two lines. Having found the 2nd line wasn't much use, I want to remove it from the config. I have taken it out of the SIP config file that is TFTPd to the phone but it is still showing on the phone and it is still trying to log into Asterisk with that account. I have tried removing the config line and blanking

Hi Everyone, I am having some issues getting my 7961 working with Trixbox. I have loaded the SIP code (8-3-3SR2) fine but when the phone boots up it goes into an unprovisioned state. A status message shows up and says ?Error Verifying Config Info?. I have read quite a bit on this topic (getting 7961?s to work with Asterisk and TB) and only came across a few postings where other people

Anyone tried integrating Cisco IP 8841 phone with Asterisk 11.x. I have the phone with sip firmware came along with sip88xx-11.0.1SR xx. I tried to upload woth TFTP due to some reason it's getting failed. Do I need to load 3pcc firmware or anyway to Configure from the phone itself or from the GUI? I have the SEPMAC.cnf.xml as well. Any suggestions would be appreciated. Regards .

I have a stupid question. How do you remove line presentations on a cisco 7960 ? I have 3 line presentations I don't use anymore and I can't figure out how to remove them.

Hi, i just want to ask whether somebody else has this problem of mine and if it can be solved. Many of my ( 30+ ) puppet installation freeze up after some time. The process is waiting for some private futex, but it stays like that forever. This is what strace looks like when the problem occures: [pid 29173] futex(0x3d35ce7a84, FUTEX_WAIT_BITSET_PRIVATE|FUTEX_CLOCK_REALTIME, 43406739,

I am trying to obtain adjusted means and standard errors for a three way ANOVA I have three effects, two continuous; fire frequency and annual precipitation, and one categorical; soil type in an unbalanced design. I am testing the effect of annual precipition (AP), soil type (ST), and fire frequency (FF) on stem count (SCt) My data table looks as such: ST FF AP SCt 3 Coy

Hi R-users, I would like to use the copula package.? I? the package plus the mvtnorm and try to run the example given, but I got the following message: install.packages(repos=NULL,pkgs="c:\\Tinn-R\\copula_0.8-3.zip") norm.cop <- normalCopula(c(0.5, 0.6, 0.7), dim = 3, dispstr = "un") t.cop <- tCopula(c(0.5, 0.3), dim = 3, dispstr = "toep", df = 2, df.fixed =

Hello everybody, I have a big problem that I do not manage to solve ! I will be very grateful if you can solve this ! I want to fit a t Copula with the copula package : > student.cop <- ellipCopula("t", param = c(0.5, 0.6, 0.7), dim = 3, dispstr = "un",df=5) > x<-rcopula(student.cop,1000) > fit <- fitCopula(x, student.cop, c(0.5,0.5,0.5,5)) And there is an

Hello R users, A beginners question which I could not find the answer to in earler posts. My thought process: Here "z" is a 119 x 15 data matrix Step 1: start at column one, bind every column with column 1 Step2: use the new matrix, "test", in the fitCopula package Step3: store each result in myfit, bind each result to "answer" Step4: return "answer"