similar to: dtmf tones problem with unicall and E1

Uys, Steve Underwood I just got a Sangoma A101 card and Im using unicall 0.0.3.pre9 for R2MFC, I get the far and local end unblocked but as soon as I try to make a call I get dialing and then protocol failure.. Do you guys know if there are any issues with sangoma and unicall? Anybody has an a101 card working with unicall and r2mfc? Are you out there Steve? :)

Hello, i've googled and can't find a definite answer, so here goes: I have purchased the Digium TE100P, and am setting up the connection, however the telco i'm supposed to work with does not support PRI/ISDN E1 connections. They only support E1/R2 lines. Is there a way i can make the TE100P work with this? I've not seen any zaptel.conf that supports this. Any workarounds?

Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of

Hi, I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I can make calls over E1, but can't receive. Here the CLI when I make a call: -- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40", "Unicall/g1/91642208|50") in new stack -- Called g1/91642208 [May 14

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

Dears, After having set up the board Digium TE420 to receive 3 E1s, I can receive calls without difficulties. As you can see in the log below: -- Executing [5908 at from-pstn:1] NoOp("UniCall/14-1", "Catch-All DID Match - Found 5908 - You probably want a DID for this.") in new stack -- Executing [5908 at from-pstn:2] Goto("UniCall/14-1",

I am having a strange problem with an asterisk servier using R2 Unicall in Mexico. Most calls go through fine but some of them give me an error like this: -- Executing Dial("SIP/86-db41", "Unicall/g2/014448343600") in new stack -- Called g2/014448343600 Feb 9 21:44:39 WARNING[23069]: chan_unicall.c:2644 handle_uc_event: Unicall/2 event Dialing Feb 9 21:44:45

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hi all, any body can tell me why i am receiving this message in my sever ? I have running * with 10 Digital Lines, but i am receiving a lot of times this message . Is a software issue or is a hardware issue ? Regards. Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:2672 handle_uc_event: Unicall/5 event Alarm Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:3091 handle_uc_event: Unicall/5 Alarm masks

Hi, ? I run the program testcall with one E1, it works fine; I receive DNIS and ANI for making calls and answering calls. ? When I start the Asterisk I receive call from outside correctly including DNIS and ANI, and receive the following messages: ? Sep? 7 10:29:59 WARNING[12167]: Answer Call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5) Sep? 7 10:29:59 WARNING[12167]: MFC/R2

I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

I have a small call center running with Asterisk 1.4.4 and Unicall. Everything seems to be working but twice now we had to reset the server because all lines stopped working. You can see users dialing in and reaching the queue but the agents never get the call and the lines are not released. I saw that there is a new Zaptel driver which fixes a racing condition with a TE110P card which is

Guys. Ive been testing how to receive faxes using TDM400P cards and so far, after playing with gains, echocancell and echotraining on zapata.conf.. Ive ha dno luck, faxes come in as garbage or broken or with blank lines. Anybody has successfully done this? Any tips.. Also I have some ideas: 1. Is it really possible to get fxes on a fax machine using ATAs like the sipura 2002? Even using ulaw

Hi all. When I place a call Im getting this error: Jul 25 09:50:07 WARNING[3200] channel.c: Exception flag set on 'UniCall/13-1', but no exception handler Lots of this messages appeared on my Asterisk full log and the CPU got 100%. Topology: Analog Phone - Hicom300H E1 - E1 Asterisk - IP Trunk Problem: 1. Calls from Analog Phone through Asterisk is ok, but the messages appeared.