similar to: my zap channel not ringing

On Thu, 2006-03-02 at 11:42 -0600, Jordan Novak wrote: > Does anyone have a way to do wake calls? > > > > Jordan Novak > > Communications Technician > > Logistics Health Inc. You could use cron and /var/spool/asterisk/outgoing scripts to dial numbers, etc... > Can you elaborate, I am fairly new to Linux and a phone guy to boot. I am looking for a way for the

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

Hi all, Can somebody help me out, to get the call going through to my provider? I connected my A104D Sangoma card to E1/isdn and each I tried to make call I get the errors below. My protocol analyzer can see only setup info and release complete. WIRELESS2*CLI> set debug 9 Core debug was 0 and is now 9 WIRELESS2*CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 T203

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hi Group, I am currently facing a dead end and any help will be much appreciated. I have an a104d installed in an asterisk box, two of which is configured on ISDN pri. One is facing pstn and the other one is facing a hipath 300e Siemens. I am getting one way audio when a local on the hipath tries to make a pstn call but no issue on incoming calls from pstn going to the hipath locals. local

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Good day eveyone, I'm hoping that someone can help me. Perhapps i'm overlooking the obvious, in truth, I hope that I am. I've scoured the mailing list and google, and haven't come up with much. I have a Digium T400P thats been connected to a channel bank for testing for some time now. all has been well. I've now just had

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.

Hi, After temporarily pulling the T1 cable out of our Asterisk box, we ended up getting a strange error messages even after the cable was plugged back in. [...] Dec 10 09:01:11 WARNING[1192437440]: File chan_zap.c, Line 5683 (zt_pri_error): PRI: Read on 63 failed: Unknown error 500 Dec 10 09:01:21 WARNING[1192437440]: File chan_zap.c, Line 5683 (zt_pri_error): PRI: Read on 63 failed: Unknown

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Hi all: I have problems to setup my zaptel E100P hardware. When I start * after receive the "Asterisk Ready" I see this: *CLI> Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 1 Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 2 Up to channel 31. anfter this: Jun 22 20:37:55

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

Guys.. I just saw this for the first time... I did some google and wiki without any luck.. what does a red or yellow alarm mean in zaptel? Feb 23 02:54:16 WARNING[16890]: chan_zap.c:5865 handle_init_event: Detected alarm on channel 2: Red Alarm Feb 23 02:54:24 NOTICE[16890]: chan_zap.c:5860 handle_init_event: Alarm cleared on channel 2 This just happened by itself..

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040928/2128c2fb/attachment.htm -------------- next part -------------- ? Hello Sir, I am new user of asterisk. I downloaded asterisk-1.0.0.tar.gz from ftp://ftp.digium.com/pub/asterisk/asterisk-1.0.0.tar.gz this ftp site. I got error while compiling. The error was chan_zap.c: In