Displaying 20 results from an estimated 2000 matches similar to: "jitterbuffer and DTMF conflict?"
2006 May 25
2
jitterbuffer causes flaky IAX2 incoming connections?
I've been having problems with incoming IAX2 calls - some work, but a
large fraction are answered with "dead air" or disconnects from my IAX
provider.
Disabling the jitterbuffer seems to eliminate the problem (so far)! Has
anyone else seen this? I'm using 1.2.6, but I'm not sure what my
provider is using.
A snippet of the a failed incoming call IAX2 debug is attached
2006 May 12
1
Speex fans?
Hi all,
I've been testing various codecs to eliminate "choppiness" that I
sometimes get on my Asterisk IAX2 <> DSL <> provider (Exgn) connections,
and Speex seems to work the best, so far - but Speex seems oddly unpopular.
Can anyone share their experiences with Speex (good and bad)? Is anyone
using it in a production environment?
I like the variable bit rate and
2006 Apr 30
2
WARNING[12785]: acl.c:244 ast_get_ip_or_srv: Unable to lookup '????'
Hi,
Red Hat 9.0
Asterisk 1.2.7.1
Whenever I start Asterisk, I am unable to call out on my SIP channel:
>-- Executing Dial("Zap/1-1", "SIP/6137451576@6477235412||t|") in new stack
>Apr 30 11:02:00 WARNING[12814]: chan_sip.c:1973 create_addr: No such
host: 6477235412
>Apr 30 11:02:01 NOTICE[12814]: app_dial.c:1029 dial_exec_full: Unable to create
>channel of type
2009 Mar 25
8
ITSP's no longer supporting IAX?
After a variety of connectivity problems, my itsp (Unlimitel.ca) blamed the
problem on the IAX protocol. They told me that as of Asterisk 1.4 the IAX
protocol went downhill and many carriers (like VoicePulse) are discontinuing
support for IAX.
Is this correct? We are all heading for SIP?
Thanks,
MD
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2007 Jan 08
3
jitterbuffer on sip.conf
In iax.conf there is option jitterbuffer
how about sip protocol ? Are jitterbuffer can configure in sip.conf ?
Thanks, for your share
2015 Jan 29
2
JITTERBUFFER function
Hello!
I am going to use the JITTERBUFFER function in a SIP (and local channels)
only setup, but have some questions of how to use it:
1. Do I need to activate jbenable in sip.conf? Or is it enough to call
the JITTERBUFFER function?
2. What is the preferred way to invoke this function? Say I have
channel A which is not in need of buffering, while channel B do need it. If
A
2005 Oct 07
1
Distorted VM with iax2 with ilbc and jitterbuffer - bug?
Two asterisk boxes 150 miles apart, both cvs-head as of this morning
(and since Sept 27th), connected via iax2 with low-utilized ds3 internet,
C7960 calls exten on remote system (also C7960), and call goes to VM.
No other calls in either system (eg, no load).
Both boxes have iax config'ed as:
trunk=yes
allow=ilbc
jitterbuffer=yes
Recorded VM messages are very distorted.
Changing only
2015 Jan 30
2
JITTERBUFFER function
WTF is a jitterbuffer?
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Matthew Jordan <mjordan at digium.com>
Date: 01/29/2015 10:41 AM (GMT-05:00)
To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at lists.digium.com>
Subject: Re: [asterisk-users] JITTERBUFFER function
On Thu, Jan 29, 2015 at 4:56 AM,
2010 Apr 08
3
jitterbuffer
What is the consensus on using the 1.4 jitterbuffer? Do most people
enable it?
We have a "PSTN" server that has our RBS T1 trunks in a central location,
then have clients that connect via SIP to us for access to those trunks.
Most of them are just fine, but lately we have a handful that are having
latency and jitter issues. I am hesitant to just turn on the jitter
buffer in
2005 Mar 19
2
More HEAD wierdness (chan_sip, jitterbuffer/PLC problems)
Hello,
After checking out CVS HEAD from yesterday (for those new
PLC/Jitterbuffer patches), I was affected by bug 3795 with my Polycom
IP600's. After seing it resolved as of this morning (thanks Mark), I
decided to try again...
I can answer incoming calls. No problem there. Putting calls on hold,
however, results in my Polycom IP600 indicating the call on hold, but
the caller does
2006 Jan 25
1
jitterbuffer causes no sound?
Hi guys,
I 've tried asterisk 1.2.2. It work flawlessly for about 3 days then at
the third days I activated setting jitterbuffer=yes and suddenly there
is no voice when the call is picked up. It's really weird as if asterisk
stops sending rtp packet. I've checked asterisk log and found nothing
suspicious. Just weird :S.
I tried it in 3 asterisk server and all of them are having
2007 Nov 02
1
Jitterbuffer issues
2011 Mar 07
3
1.8.3 - IAX - echo - jitterbuffer
I'm using iaxagent on a Droid X to connect by IAX to 1.8.3 at the
office. 1.8.3 has sip phones. The audio is fine on the Droid X side. On
the office side, they hear an echo of _their_ speech, not mine.
The office uses sip-providers generally without any echo problem.
Where do I start to figure this out? How do I narrow it down? Can I
figure out if it is an iaxagent problem? Could using
2005 Mar 01
2
Important :: Please support the development of a new Jitterbuffer for SIP
Steve Kann has developed a new jitterbuffer for IAX2, that hopefully
will be integrated into Asterisk v1.1 soon, to be part of the 1.2 stable
relase.
Zoa and his bulgarian team is porting this buffer to SIP/RTP, but needs
support in the form of funding in order to take the time to test this
out and complete it in time.
Please paypal your contribution to sponsor@astertest.com today. Every
2009 Sep 01
4
jitterbuffer for chan_sip on asterisk 1.2
Hello,
2006 Apr 26
1
Phone Emergency - Need IAX Help
SBC has an outage that is expected to last until tomorrow
in our area. This has taken out our 5 POTS lines and our T1.
I have signed up with EXGN for outbound calls and am using
IAX. Calls ring through to the other party (my cell phone in
this case) but Asterisk doesn't seem to think the call
was answered. Ideas?
-dave
2004 Aug 27
5
iaxtel and jitterbuffer
I am trying to work out IAX <--> IAX communications with my * box. I have a
registration with iaxtel and I thought I would start there for my learning.
I am able to call the number for Digium's support line (700-428-6000), but the
sound is horribly chopping. Some reading revealed the jitterbuffer settings,
so I enabled them in iax.conf. I have the following now:
; Inter-Asterisk
2006 Feb 20
9
Asterisk 1.2.4 IAX2 New Jitterbuffer Tuning
I was using G729 with Asterisk 1.07. With the new ability to do packet
loss correction with ILBC, I felt I'd give it a try. The new PLC does
not work with G729. I don't use Speex because my softphone does not
support it.
This is a 1.5mb IP-VPN connection with prioritized QOS for port 4569
(IAX2). I've never really stressed the bandwidth. Typically, only
10-20 concurrent calls.
2010 Jan 15
1
jitterbuffer and PLC
Hi, I have a question about jitterbuffer and PLC.
I use Asterisk 1.6.2.0 and 1.6.0.20 or older.
I use uLaw.
My system map:
=============================================================================
[ asterisk 2 ] -- # LOSS # -- # A # -- [ asterisk 1 ] -- # B # -- [ X-lite ]
=============================================================================
I use two asterisk server.
2015 Feb 18
1
SIP Jitterbuffer
Hello people
What are the cons, if any, of enabling a jitterbuffer?
We are currently using version 1.8
Thanks in advance
Ish
--
Ishfaq Malik
Department: VOIP Support
Company: Packnet Limited
t: +44 (0)845 004 4994
f: +44 (0)161 660 9825
e: ish at pack-net.co.uk
w: http://www.pack-net.co.uk
Registered Address: PACKNET LIMITED, Duplex 2, Ducie House
37 Ducie Street
Manchester, M1 2JW
COMPANY