similar to: Unknown RTP codec 100 received

I have a Sipura SPA2000 2 line SIP FXS box with line 1 on port 5060 and line 2 on 5061. The SPA2000 is on IP address 192.168.17.6, and the asterisk box is on 102.168.17.2. Both SPA2000 ports(5060 and 5061) share the same IP address. Every minute I repeatedly get the following output: SIP Debugging Enabled 10 headers, 0 lines Reliably Transmitting: OPTIONS sip:192.168.17.6 SIP/2.0 Via:

All, If you currently own a Sipura SPA2000, avoid going to the sipura website and upgrading the firmware. I upgraded my SPA2k a couple of days ago from 1.0.9 (what it came with) to 1.0.18 off the site, and I am having issues with my SPA rebooting itself every 3-10 minutes for no apparent reason. I have been in touch with the *excellent* sipura support folks, and they are working with me to

Hi, I've one Sipura SPA2000 at home behind a linuxbox with two network adapters (eth0 for WAN and eth1 for LAN) doing NAT/DHCP: ___________ HOME _______________ ____OFFICE ____ SPA2000 <---> Linux Box <--> Asterisk Box 192.168.0.253 192.168.0.1 eth1 200.93.xxx.a 200.93.xxx.b eth0 My problem is when I try to call to any trunk or extention

Hello We have setup a doorbell which has an inbuilt analog phone which is connected to our Asterisk via a SPA2000 ATA. The problem we are getting is that when a caller presses the buzzer it is taking two or more minutes to finally call the reception phone. In the SPA2000 I have set dtmfmode to be inband. I notice that with the asterisk you dial a number and then it waits for a timeout

Thanks. I'm able to getting the asterisk calling back to my cellphone. But when I get to the authentication I get this message when I start to dial in my password: NOTICE[5178]: rtp.c:509 ast_rtp_read: Unknown RTP codec 96 received Is this a DTMF failure of some sort? Thanks again. -----Opprinnelig melding----- Fra: asterisk-users-bounces@lists.digium.com

Hi My head hurts... Can anyone help out here, my remote IAX can see my local IAX and visa versa, conversation starts, I can dial my remote (POTS) landline number, remote end answers, trys to route to local iax2, I see it start the conversation here, the extension (SIP) rings once and then it dies... Both ends are defined with accept IPADDRESS to keep it in the family and simple.. Debug info

Been having a problem with my two Sipura 2000's dropping calls from the SPA-2000 side. Seems the calls are dropped right before the "Next Registration" time. Calls drop about ever 60 minutes or so. I have dialed from one port to the other and let it sit. After about 60 minutes or so the calls get dropped. System details are below Asterisk ver. CVS-HEAD-11/27/04-23:42:45 RHEL 3

was breezing over http://voxilla.com/ Looks like a new ATA from the founder of Komodo Technology (aka the Cisco 186) Sipura SPA 2000 http://www.sipura.com/products/spa2000.htm to join the others Cisco ATA 186/188 http://www.cisco.com/warp/public/cc/pd/as/180/186/ 8x8 DTA-310 http://www.8x8.com/products/home_office/dta-310/index.asp.html Grandstream HandyTone 286

is it possible to achive the following scenario? faxmachine--tdm40bFXS--SIPnetwork--Gateway--faxmachine i have found a lot of documents about asterisk receiving a fax and saving it to a file. But i want to receive the fax via SIP and send it to my faxmachine. I also want to send a fax from my faxmachine through the digium card, so asterisk should send the fax via SIP to the gateway, which also

I can cut and paste the log file from a reload right now, and provide you with the other information when I get home after work: tmp*CLI> sip debug SIP Debugging Enabled tmp*CLI> reload Mar 21 14:52:42 NOTICE[23231]: indications.c:397 ast_unregister_indication_country: Removed default indication country 'us' 11 headers, 0 lines Reliably Transmitting: REGISTER

I've gotten hold of a "Tesco Internet Phone" which is a dect phone with the base connecting to the pc via usb. Has anyone been able to get this working with any softphone like xlite ? It seems as if the tesco internet phone uses IAX - the software that comes with it is a rebranded firefly (or so it seems) I already have a SPA2000 and SPA3000 hooked up, but I was just curious to

Hello, In our SIP network, Asterisk is the central PBX, and it routes calls to the PSTN thru a Cisco Router - IOS 12.2(11)T9. If a client softphone calls directly via Cisco to the PSTN, the call works successfully. If the client softphone calls via Asterisk to other SIP internal extension, it work fine too. The problem is when a client calls an Asterisk extension, and Asterisk transfers

I have a small * system in my home (1 U100S, 1 X100P, 1 BT101, and 1 SPA2000) to handle my requirements. I would like to add Music on Hold and have been watching the forum to see if something would come across on this topic. The difference I am interested in is getting the music from a radio or someother external source. All references to MOH up to now have been using MP3 files and going

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

I have a similar setup to you and get the same message regularly. I don't think it's the cause of your problem. I did some research on it a while ago: IIRC the cisco uses codec 13 for "silence suppression" whereas asterisk (correctly) uses codec 19. The router can be configured to use 19 also, but I didn't bother. I'm sure somebody will correct me if I'm wrong about

Hi folks, I am having a small problem with asterisk-1.6.2.7 + app_fax on OpenBSD 4.7 -release. Everything seems to work fine. I have a macro which answers, receives the fax to a tiff, and then runs a script (mailfax) to convert that to pdf and email it. It all works perfectly except for some errors I am seeing in the console. After it hangs up I get a dozen or so messages in the cli

Hi list,* *I am not able to make video calls between two sip accounts. below is the information. please help me where I am missing the configuration.* Extensions.conf* exten => 111,1,Answer() same => n,Dial(SIP/2206,60,r) same => n,Hangup() *SIP.conf* [2218] type=friend secret=******* callerid="Virendra" <9172341457> host=dynamic ;

We have a customer trying to dial through our server, and our server is throwing tons of these log messages: Jul 27 14:21:02 NOTICE[29210]: rtp.c:431 ast_rtp_read: RTP: Received packet with bad UDP checksum Is it pretty certain, that these are caused by a bad or misconfigured router along the path, or something else network-related? As opposed to the SIP hardware itself? The SIP ATA is the same

I am trying to get the handytone 286 to make a very simple call to * and having problems. It registers with * just fine, but when I place a call (to echo test, for example), the RTP stream seems to have problems opening. Here is there error I get in *: WARNING[98311]: File chan_sip.c, Line 464 (retrans_pkt): Maximum retries exceeded on call 20d1c411-e210-5f3d-3f88-19035c8fcb26@192.168.2.6 for

Hi All, I have Asterisk 1.2.9.1 sending SIP calls to a Cisco 2620XM Router with a PRI card in it, handing off to a PBX and vise verse. Calls in and out are working fine except for DTMF from Asterisk to the 2600. DTMF from the 2600 to Asterisk is fine. Here are the Asterisk console warnings I get when I send DTMF from Asterisk to the 2600: == Forcing Marker bit, because SSRC has changed Jun