similar to: How to reset Digium card while asterisk is running?

I have the following software installed in a Centos Box with a TE420 (5th Gen) card. . Centos 6.5 64-bit . Asterisk 1.4.22 . dahdi-linux-complete-2.9.1.1+2.9.1 . libpri-1.4.14. Even without plugging in the ISDN into span 1, all 4 spans are flashing red. Plugging an E1 into span 1 makes no difference. My system.conf is just simply: loadzone=au defaultzone=au span=1,1,0,ccs,hdb3,crc4 bchan=1-15

Hello all- I have a Digium TE410P in an HP DL145 G2 dual processor server that generates well over 100,000 interrupts per second (sometimes I?ve counted 160,000+ per second) generally resulting in either the system becoming swamped and unusable or the kernel disabling the IRQ the TE410P is on resulting in the spans on that card being unusable. I have confirmed that the card is good by placing it

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

Hi, I have on my dual opteron (64 bit mode, linux) the problem, that sometimes read errors (unknown error 500) occur. This was already discussed on some asterisk list, and the solution seems to be to put the digium card on the highest interrupt level. Unfortunately I don't know howto. Applying an irq parameter when loading the module don't work: wct4xxp: Unknown parameter `irq'

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Hello, I need help to install a digium card TC400P. I compiled the dahdi source, but dahdi don?t find the card! debian:/usr/src/dahdi-linux-complete-2.2.0.2+2.2.0# lspci 11:03.0 Ethernet controller: Digium, Inc. Wildcard TC400P transcoder base card (rev 11) debian:/usr/src/dahdi-linux-complete-2.2.0.2+2.2.0# /etc/init.d/dahdi restart Unloading DAHDI hardware modules:

I've seen this consistently on three systems, with three different cards, and multiple versions of DAHDI. At first I thought the issue only occurred on newer, Nehalem-based, systems, but I reproduced it on a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi- linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The card is a Digium TE220B which uses the

I attempted an upgrade of our production system from Asterisk/Zaptel 1.2 to 1.4 this weekend. Intially everything looked like it was working properly, but some time in the day following the upgrade, the system died to a kernel panic. I wasn't able to catch the entire kernel dump on the console unfortunately. I attempted to isolate the panic, and found that when 'service zaptel stop'

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

I'm having a bad time getting 3 TE410P's and one TDM400 working in the same box. At some point during the install of second card, wcusb starts loading. I believe this is one of the TE410 Cards causing this as there is no usb enabled. Module Size Used by Not tainted audit 89880 2 (autoclean) usbserial 23420 0 (autoclean) (unused)

Hello, I`ve got a problem which I can`t deal with. I own 2 cards - TDM2400P and TE410P. I`ve put them into a HP Proliant DL380 G4 server, compiled the drivers according to the manual. Unfortunetly there are both cards channels are configured in zaptel.conf file the first module (in this file) sends an error. For configuration: span = 1, 1, 0, ccs, hdb3, crc4 fxsks = 21-24 bchan = 25-39,

Hi. I'm just trying to install a TE410P card (jumped as E1). But I'm having problems loading the kernel module. [root@asterisk1 src]# modprobe wct4xxp /lib/modules/2.4.21-32.0.1.ELsmp/misc/wct4xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the

I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS). These connect to a Digium TE210P card. I'm running kernel 2.6.10 and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today. The results are the same for all versions: Right after I reboot, and modprobe wct4xxp, my analog phone connected to port 13 of the first channel bank (first FXS port) gets a dial

Dear All I installed a Digium card TE405P with zaptel and its running successfully with no alarms, but asterisk is not running . Any one have a cure or advice 03:09.0 Communication controller: Digium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02) Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing yellow alarm on span 2 Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing

Hello All, I have 2 Digium card configure on Single machine, which can't share interrupt across all CPUs and sometimes asterisk reach 100% CPU usage. Here is system details and /proc/interrupt o/p. OS: CentOS 6.4 Kernel: 2.6.32-431.11.2.el6.x86_64 Dahdi Version: DAHDI Version: 2.7.0.2 Echo Canceller: HWEC Asterisk Version: 1.8.13.0 Output: /proc/interrupts cat /proc/interrupts

Thanks, chdir dir /data error seems go away, but at 12:00 o'clock the following error appear: Feb 20 11:45:03 brulx01 vsftpd: Mon Feb 20 11:45:03 2006 [pid 12273] [job260] OK DOWNLOAD: Client "10.90.1.1", "/data/mde/DATA/.././ACTUAL/mdeact260.msg", 12481 bytes, 174.76Kbyte/sec Feb 20 11:56:10 brulx01 smbd[12410]: [2006/02/20 11:56:10, 0]

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules