James FitzGibbon
2007-May-22 07:07 UTC
[asterisk-users] Kernel Panic in wct4xxp during unload on Zaptel-1.4.4
I attempted an upgrade of our production system from Asterisk/Zaptel 1.2 to 1.4 this weekend. Intially everything looked like it was working properly, but some time in the day following the upgrade, the system died to a kernel panic. I wasn't able to catch the entire kernel dump on the console unfortunately. I attempted to isolate the panic, and found that when 'service zaptel stop' was run (specifically, when wct4xxp was unloaded) I get this panic consistently: <5> Not prepped yet! (repeated approx 250 times) <5> Freed a Wildcard <5> Not prepped yet! (repeated approx 550 times) <5> Stopped TE4XXP, Turned off DMA <5> Not prepped yet! (repeated approx 11000 times) <5> Unable to handle kernel paging request at ffffff0000034010 RIP: <5> <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} <5> PML4 4ea063 PGD 1388067 PMD 1389067 PTE 0 <5> Oops: 0000 [1] SMP <5> CPU 1 <5> Modules linked in: zttranscode(U) wct4xxp(U) zaptel(U) crc_ccitt netconsole md5 ipv6 dm_mirror dm_mod button battery ac joydev ehci_hcd uhci_hcd hw_random bnx2 ext3 jbd cciss sd_mod scsi_mod <5> Pid: 11053, comm: hotplug Not tainted 2.6.9-42.0.8.ELsmp <5> RIP: 0010:[<ffffffffa0163207>] <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} <5> RSP: 0000:00000100013ebdb0 EFLAGS: 00010046 <5> RAX: ffffff0000034000 RBX: 0000010073478724 RCX: 0000000000000002 <5> RDX: 0000010073478680 RSI: 0000000000000002 RDI: 0000010073478724 <5> RBP: 0000010073478680 R08: 0000000000000008 R09: 0000000000000000 <5> R10: 0000000000000000 R11: 0000000000000002 R12: 00000000000000d1 <5> R13: 00000100013ebec8 R14: 00000100013ebec8 R15: 0000010075e94978 <5> FS: 0000002a955643e0(0000) GS:ffffffff804e5900(0000) knlGS:0000000000000000 <5> CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b <5> CR2: ffffff0000034010 CR3: 00000000013d8000 CR4: 00000000000006e0 <5> Process hotplug (pid: 11053, threadinfo 000001007413c000, task 000001007c445030) <5> Stack: 00000000000000d1 000001007413dc98 ffffffff80138552 0000003000000008 <5> 00000100013ebea8 00000100013ebde8 0000000000000001 00000000000000d1 <5> 0000000000000012 0000010073478680 <5> Call Trace:<IRQ> <ffffffff80138552>{printk+141} <ffffffff80112f4a>{handle_IRQ_event+41} <5> <ffffffff801131c4>{do_IRQ+197} <ffffffff80110833>{ret_from_intr+0} <5> <ffffffff8013c731>{__do_softirq+77} <ffffffff8013c7e5>{do_softirq+49} <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> <ffffffff8011c21a>{flush_tlb_page+44} <5> <ffffffff80169106>{do_wp_page+1127} <ffffffff80123ed3>{do_page_fault+575} <5> <ffffffff80169ff2>{handle_mm_fault+1228} <ffffffff80123e9a>{do_page_fault+518} <5> <ffffffff8011026a>{system_call+126} <ffffffff80132bc6>{schedule_tail+202} <5> <ffffffff80110d91>{error_exit+0} <5> <5> Code: 8b 40 10 89 44 24 58 e8 3d 80 1a e0 31 c0 f6 44 24 58 07 0f <5> RIP <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} RSP <00000100013ebdb0> <5> CR2: ffffff0000034010 <5> <0>Kernel panic - not syncing: Oops <5> Badness in panic at kernel/panic.c:118 <5> <5> Call Trace:<IRQ> <ffffffff80137a8a>{panic+527} <ffffffff80110bf5>{apic_timer_interrupt+133} <5> <ffffffff80111aec>{oops_end+38} <ffffffff80111b07>{oops_end+65} <5> <ffffffff80124148>{do_page_fault+1204} <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} <5> <ffffffff802bb4cd>{netpoll_send_skb+257} <ffffffff80110d91>{error_exit+0} <5> <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} <ffffffff80138552>{printk+141} <5> <ffffffff80112f4a>{handle_IRQ_event+41} <ffffffff801131c4>{do_IRQ+197} <5> <ffffffff80110833>{ret_from_intr+0} <ffffffff8013c731>{__do_softirq+77} <5> <ffffffff8013c7e5>{do_softirq+49} <ffffffff80110bf5>{apic_timer_interrupt+133} <5> <EOI> <ffffffff8011c21a>{flush_tlb_page+44} <ffffffff80169106>{do_wp_page+1127} <5> <ffffffff80123ed3>{do_page_fault+575} <ffffffff80169ff2>{handle_mm_fault+1228} <5> <ffffffff80123e9a>{do_page_fault+518} <ffffffff8011026a>{system_call+126} <5> <ffffffff80132bc6>{schedule_tail+202} <ffffffff80110d91>{error_exit+0} <5> <5> Badness in i8042_panic_blink at drivers/input/serio/i8042.c:987 <5> <5> Call Trace:<IRQ> <ffffffff8024219b>{i8042_panic_blink+238} <ffffffff80137a38>{panic+445} <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <ffffffff80111aec>{oops_end+38} <5> <ffffffff80111b07>{oops_end+65} <ffffffff80124148>{do_page_fault+1204} <5> <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} <ffffffff802bb4cd>{netpoll_send_skb+257} <5> <ffffffff80110d91>{error_exit+0} <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} <5> <ffffffff80138552>{printk+141} <ffffffff80112f4a>{handle_IRQ_event+41} <5> <ffffffff801131c4>{do_IRQ+197} <ffffffff80110833>{ret_from_intr+0} <5> <ffffffff8013c731>{__do_softirq+77} <ffffffff8013c7e5>{do_softirq+49} <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> <ffffffff8011c21a>{flush_tlb_page+44} <5> <ffffffff80169106>{do_wp_page+1127} <ffffffff80123ed3>{do_page_fault+575} <5> <ffffffff80169ff2>{handle_mm_fault+1228} <ffffffff80123e9a>{do_page_fault+518} <5> <ffffffff8011026a>{system_call+126} <ffffffff80132bc6>{schedule_tail+202} <5> <ffffffff80110d91>{error_exit+0} <5> Badness in i8042_panic_blink at drivers/input/serio/i8042.c:990 <5> <5> Call Trace:<IRQ> <ffffffff8024222d>{i8042_panic_blink+384} <ffffffff80137a38>{panic+445} <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <ffffffff80111aec>{oops_end+38} <5> <ffffffff80111b07>{oops_end+65} <ffffffff80124148>{do_page_fault+1204} <5> <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} <ffffffff802bb4cd>{netpoll_send_skb+257} <5> <ffffffff80110d91>{error_exit+0} <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} <5> <ffffffff80138552>{printk+141} <ffffffff80112f4a>{handle_IRQ_event+41} <5> <ffffffff801131c4>{do_IRQ+197} <ffffffff80110833>{ret_from_intr+0} <5> <ffffffff8013c731>{__do_softirq+77} <ffffffff8013c7e5>{do_softirq+49} <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> <ffffffff8011c21a>{flush_tlb_page+44} <5> <ffffffff80169106>{do_wp_page+1127} <ffffffff80123ed3>{do_page_fault+575} <5> <ffffffff80169ff2>{handle_mm_fault+1228} <ffffffff80123e9a>{do_page_fault+518} <5> <ffffffff8011026a>{system_call+126} <ffffffff80132bc6>{schedule_tail+202} <5> <ffffffff80110d91>{error_exit+0} <5> Badness in i8042_panic_blink at drivers/input/serio/i8042.c:992 <5> <5> Call Trace:<IRQ> <ffffffff80242292>{i8042_panic_blink+485} <ffffffff80137a38>{panic+445} <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <ffffffff80111aec>{oops_end+38} <5> <ffffffff80111b07>{oops_end+65} <ffffffff80124148>{do_page_fault+1204} <5> <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} <ffffffff802bb4cd>{netpoll_send_skb+257} <5> <ffffffff80110d91>{error_exit+0} <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} <5> <ffffffff80138552>{printk+141} <ffffffff80112f4a>{handle_IRQ_event+41} <5> <ffffffff801131c4>{do_IRQ+197} <ffffffff80110833>{ret_from_intr+0} <5> <ffffffff8013c731>{__do_softirq+77} <ffffffff8013c7e5>{do_softirq+49} <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> <ffffffff8011c21a>{flush_tlb_page+44} <5> <ffffffff80169106>{do_wp_page+1127} <ffffffff80123ed3>{do_page_fault+575} <5> <ffffffff80169ff2>{handle_mm_fault+1228} <ffffffff80123e9a>{do_page_fault+518} <5> <ffffffff8011026a>{system_call+126} <ffffffff80132bc6>{schedule_tail+202} <5> <ffffffff80110d91>{error_exit+0} System details: HP DL380G5 CentOS x86_64 4.4 uname: 2.6.9-42.0.8.ELsmp #1 SMP Tue Jan 30 12:18:01 EST 2007 x86_64 x86_64 x86_64 GNU/Linux T412P quad-span card TDM400 card with two FXS modules and two FXO modules Original software: Libpri 1.2.4 (RPM from atrpms) Zaptel 1.2.16 (RPM from atrpms) Asterisk 1.2.17 (compiled from source) Upgraded software: Libpri 1.4.0 (compiled from source) Zaptel 1.4.2.1 (compiled from source) Asterisk 1.4.4 (compiled from source) Before installing the 1.4 files, I removed the 1.2 RPMs using 'yum remove', so there should not have been any cruft left over. I did notice that the atrpms tarballs put some files in different locations. The RPM for libpri puts the files in /usr/lib64, while my source tarball put them in /usr/lib. 'file' indicates that they are both 'ELF 64-bit LSB shared object, AMD x86-64, version 1 (SYSV)' though, so I don't think that this is an issue of mixed 32 and 64 bit objects. I tried rebuilding all of the software from cleanly extracted tarballs to no avail, so I had to restore my backed up 1.2 configuration. Things still aren't working properly: when I attempt to unload the wct4xxp module, the "Not prepped yet!" message floods the console and the 'rmmod' command becomes hung (unkillable), but the system does not panic. I still have to hard reboot to get the system in a state where I can bring up * again though. Since the panic seems to involve the T412P interrupts, here's the output of /proc/interrupts: [root@pbxtel-01 ~]# cat /proc/interrupts CPU0 CPU1 0: 799008 804849 IO-APIC-edge timer 1: 4 5 IO-APIC-edge i8042 8: 5 1 IO-APIC-edge rtc 9: 0 0 IO-APIC-level acpi 74: 16224 3990 PCI-MSI-X cciss0 90: 154441 0 PCI-MSI eth0 169: 0 0 IO-APIC-level uhci_hcd, ehci_hcd 177: 0 0 IO-APIC-level uhci_hcd 185: 0 0 IO-APIC-level uhci_hcd 193: 0 0 IO-APIC-level uhci_hcd 201: 814161 720175 IO-APIC-level wctdm 209: 720174 814169 IO-APIC-level wct4xxp 233: 34 47 IO-APIC-level uhci_hcd NMI: 1603725 1603680 LOC: 1603015 1603015 ERR: 0 MIS: 0 [root@pbxtel-01 ~]# (this is with the system as it is running now with the backed out to 1.2configuration) Any thoughts? Thanks -- j. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070522/245eec53/attachment.htm
Axel Thimm
2007-May-22 08:16 UTC
[asterisk-users] Re: Kernel Panic in wct4xxp during unload on Zaptel-1.4.4
On Tue, May 22, 2007 at 10:07:19AM -0400, James FitzGibbon wrote:> I attempted an upgrade of our production system from Asterisk/Zaptel 1.2 to > 1.4 this weekend. Intially everything looked like it was working properly, > but some time in the day following the upgrade, the system died to a kernel > panic. I wasn't able to catch the entire kernel dump on the console > unfortunately. > > I attempted to isolate the panic, and found that when 'service zaptel stop' > was run (specifically, when wct4xxp was unloaded) I get this panic > consistently: > > <5> Not prepped yet! (repeated approx 250 times) > <5> Freed a Wildcard > <5> Not prepped yet! (repeated approx 550 times) > <5> Stopped TE4XXP, Turned off DMA > <5> Not prepped yet! (repeated approx 11000 times) > <5> Unable to handle kernel paging request at ffffff0000034010 RIP: > <5> <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} > <5> PML4 4ea063 PGD 1388067 PMD 1389067 PTE 0 > <5> Oops: 0000 [1] SMP > <5> CPU 1 > <5> Modules linked in: zttranscode(U) wct4xxp(U) zaptel(U) crc_ccitt > netconsole md5 ipv6 dm_mirror dm_mod button battery ac joydev ehci_hcd > uhci_hcd hw_random bnx2 ext3 jbd > cciss sd_mod scsi_mod > <5> Pid: 11053, comm: hotplug Not tainted 2.6.9-42.0.8.ELsmp > <5> RIP: 0010:[<ffffffffa0163207>] > <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} > <5> RSP: 0000:00000100013ebdb0 EFLAGS: 00010046 > <5> RAX: ffffff0000034000 RBX: 0000010073478724 RCX: 0000000000000002 > <5> RDX: 0000010073478680 RSI: 0000000000000002 RDI: 0000010073478724 > <5> RBP: 0000010073478680 R08: 0000000000000008 R09: 0000000000000000 > <5> R10: 0000000000000000 R11: 0000000000000002 R12: 00000000000000d1 > <5> R13: 00000100013ebec8 R14: 00000100013ebec8 R15: 0000010075e94978 > <5> FS: 0000002a955643e0(0000) GS:ffffffff804e5900(0000) > knlGS:0000000000000000 > <5> CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b > <5> CR2: ffffff0000034010 CR3: 00000000013d8000 CR4: 00000000000006e0 > <5> Process hotplug (pid: 11053, threadinfo 000001007413c000, task > 000001007c445030) > <5> Stack: 00000000000000d1 000001007413dc98 ffffffff80138552 > 0000003000000008 > <5> 00000100013ebea8 00000100013ebde8 0000000000000001 > 00000000000000d1 > <5> 0000000000000012 0000010073478680 > <5> Call Trace:<IRQ> <ffffffff80138552>{printk+141} > <ffffffff80112f4a>{handle_IRQ_event+41} > <5> <ffffffff801131c4>{do_IRQ+197} > <ffffffff80110833>{ret_from_intr+0} > <5> <ffffffff8013c731>{__do_softirq+77} > <ffffffff8013c7e5>{do_softirq+49} > <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> > <ffffffff8011c21a>{flush_tlb_page+44} > <5> <ffffffff80169106>{do_wp_page+1127} > <ffffffff80123ed3>{do_page_fault+575} > <5> <ffffffff80169ff2>{handle_mm_fault+1228} > <ffffffff80123e9a>{do_page_fault+518} > <5> <ffffffff8011026a>{system_call+126} > <ffffffff80132bc6>{schedule_tail+202} > <5> <ffffffff80110d91>{error_exit+0} > <5> > <5> Code: 8b 40 10 89 44 24 58 e8 3d 80 1a e0 31 c0 f6 44 24 58 07 0f > <5> RIP <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} RSP > <00000100013ebdb0> > <5> CR2: ffffff0000034010 > <5> <0>Kernel panic - not syncing: Oops > <5> Badness in panic at kernel/panic.c:118 > <5> > <5> Call Trace:<IRQ> <ffffffff80137a8a>{panic+527} > <ffffffff80110bf5>{apic_timer_interrupt+133} > <5> <ffffffff80111aec>{oops_end+38} <ffffffff80111b07>{oops_end+65} > <5> <ffffffff80124148>{do_page_fault+1204} > <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} > <5> <ffffffff802bb4cd>{netpoll_send_skb+257} > <ffffffff80110d91>{error_exit+0} > <5> <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} > <ffffffff80138552>{printk+141} > <5> <ffffffff80112f4a>{handle_IRQ_event+41} > <ffffffff801131c4>{do_IRQ+197} > <5> <ffffffff80110833>{ret_from_intr+0} > <ffffffff8013c731>{__do_softirq+77} > <5> <ffffffff8013c7e5>{do_softirq+49} > <ffffffff80110bf5>{apic_timer_interrupt+133} > <5> <EOI> <ffffffff8011c21a>{flush_tlb_page+44} > <ffffffff80169106>{do_wp_page+1127} > <5> <ffffffff80123ed3>{do_page_fault+575} > <ffffffff80169ff2>{handle_mm_fault+1228} > <5> <ffffffff80123e9a>{do_page_fault+518} > <ffffffff8011026a>{system_call+126} > <5> <ffffffff80132bc6>{schedule_tail+202} > <ffffffff80110d91>{error_exit+0} > <5> > <5> Badness in i8042_panic_blink at drivers/input/serio/i8042.c:987 > <5> > <5> Call Trace:<IRQ> <ffffffff8024219b>{i8042_panic_blink+238} > <ffffffff80137a38>{panic+445} > <5> <ffffffff80110bf5>{apic_timer_interrupt+133} > <ffffffff80111aec>{oops_end+38} > <5> <ffffffff80111b07>{oops_end+65} > <ffffffff80124148>{do_page_fault+1204} > <5> <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} > <ffffffff802bb4cd>{netpoll_send_skb+257} > <5> <ffffffff80110d91>{error_exit+0} > <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} > <5> <ffffffff80138552>{printk+141} > <ffffffff80112f4a>{handle_IRQ_event+41} > <5> <ffffffff801131c4>{do_IRQ+197} > <ffffffff80110833>{ret_from_intr+0} > <5> <ffffffff8013c731>{__do_softirq+77} > <ffffffff8013c7e5>{do_softirq+49} > <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> > <ffffffff8011c21a>{flush_tlb_page+44} > <5> <ffffffff80169106>{do_wp_page+1127} > <ffffffff80123ed3>{do_page_fault+575} > <5> <ffffffff80169ff2>{handle_mm_fault+1228} > <ffffffff80123e9a>{do_page_fault+518} > <5> <ffffffff8011026a>{system_call+126} > <ffffffff80132bc6>{schedule_tail+202} > <5> <ffffffff80110d91>{error_exit+0} > <5> Badness in i8042_panic_blink at drivers/input/serio/i8042.c:990 > <5> > <5> Call Trace:<IRQ> <ffffffff8024222d>{i8042_panic_blink+384} > <ffffffff80137a38>{panic+445} > <5> <ffffffff80110bf5>{apic_timer_interrupt+133} > <ffffffff80111aec>{oops_end+38} > <5> <ffffffff80111b07>{oops_end+65} > <ffffffff80124148>{do_page_fault+1204} > <5> <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} > <ffffffff802bb4cd>{netpoll_send_skb+257} > <5> <ffffffff80110d91>{error_exit+0} > <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} > <5> <ffffffff80138552>{printk+141} > <ffffffff80112f4a>{handle_IRQ_event+41} > <5> <ffffffff801131c4>{do_IRQ+197} > <ffffffff80110833>{ret_from_intr+0} > <5> <ffffffff8013c731>{__do_softirq+77} > <ffffffff8013c7e5>{do_softirq+49} > <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> > <ffffffff8011c21a>{flush_tlb_page+44} > <5> <ffffffff80169106>{do_wp_page+1127} > <ffffffff80123ed3>{do_page_fault+575} > <5> <ffffffff80169ff2>{handle_mm_fault+1228} > <ffffffff80123e9a>{do_page_fault+518} > <5> <ffffffff8011026a>{system_call+126} > <ffffffff80132bc6>{schedule_tail+202} > <5> <ffffffff80110d91>{error_exit+0} > <5> Badness in i8042_panic_blink at drivers/input/serio/i8042.c:992 > <5> > <5> Call Trace:<IRQ> <ffffffff80242292>{i8042_panic_blink+485} > <ffffffff80137a38>{panic+445} > <5> <ffffffff80110bf5>{apic_timer_interrupt+133} > <ffffffff80111aec>{oops_end+38} > <5> <ffffffff80111b07>{oops_end+65} > <ffffffff80124148>{do_page_fault+1204} > <5> <ffffffffa0078f51>{:bnx2:bnx2_start_xmit+470} > <ffffffff802bb4cd>{netpoll_send_skb+257} > <5> <ffffffff80110d91>{error_exit+0} > <ffffffffa0163207>{:wct4xxp:t4_interrupt_gen2+63} > <5> <ffffffff80138552>{printk+141} > <ffffffff80112f4a>{handle_IRQ_event+41} > <5> <ffffffff801131c4>{do_IRQ+197} > <ffffffff80110833>{ret_from_intr+0} > <5> <ffffffff8013c731>{__do_softirq+77} > <ffffffff8013c7e5>{do_softirq+49} > <5> <ffffffff80110bf5>{apic_timer_interrupt+133} <EOI> > <ffffffff8011c21a>{flush_tlb_page+44} > <5> <ffffffff80169106>{do_wp_page+1127} > <ffffffff80123ed3>{do_page_fault+575} > <5> <ffffffff80169ff2>{handle_mm_fault+1228} > <ffffffff80123e9a>{do_page_fault+518} > <5> <ffffffff8011026a>{system_call+126} > <ffffffff80132bc6>{schedule_tail+202} > <5> <ffffffff80110d91>{error_exit+0} > > System details: > > HP DL380G5 > CentOS x86_64 4.4 > uname: 2.6.9-42.0.8.ELsmp #1 SMP Tue Jan 30 12:18:01 EST 2007 x86_64 x86_64 > x86_64 GNU/Linux > T412P quad-span card > TDM400 card with two FXS modules and two FXO modules > > Original software: > Libpri 1.2.4 (RPM from atrpms) > Zaptel 1.2.16 (RPM from atrpms) > Asterisk 1.2.17 (compiled from source) > > Upgraded software: > Libpri 1.4.0 (compiled from source) > Zaptel 1.4.2.1 (compiled from source) > Asterisk 1.4.4 (compiled from source)Have you tried using the 1.4.x atrpms packages?> Before installing the 1.4 files, I removed the 1.2 RPMs using 'yum remove', > so there should not have been any cruft left over. I did notice that the > atrpms tarballs put some files in different locations. The RPM for libpri > puts the files in /usr/lib64, while my source tarball put them in /usr/lib. > 'file' indicates that they are both 'ELF 64-bit LSB shared object, AMD > x86-64, version 1 (SYSV)' though, so I don't think that this is an issue of > mixed 32 and 64 bit objects. > > I tried rebuilding all of the software from cleanly extracted tarballs to no > avail, so I had to restore my backed up 1.2 configuration. Things still > aren't working properly: when I attempt to unload the wct4xxp module, the > "Not prepped yet!" message floods the console and the 'rmmod' command > becomes hung (unkillable), but the system does not panic. I still have to > hard reboot to get the system in a state where I can bring up * again > though. > > Since the panic seems to involve the T412P interrupts, here's the output of > /proc/interrupts: > > [root@pbxtel-01 ~]# cat /proc/interrupts > CPU0 CPU1 > 0: 799008 804849 IO-APIC-edge timer > 1: 4 5 IO-APIC-edge i8042 > 8: 5 1 IO-APIC-edge rtc > 9: 0 0 IO-APIC-level acpi > 74: 16224 3990 PCI-MSI-X cciss0 > 90: 154441 0 PCI-MSI eth0 > 169: 0 0 IO-APIC-level uhci_hcd, ehci_hcd > 177: 0 0 IO-APIC-level uhci_hcd > 185: 0 0 IO-APIC-level uhci_hcd > 193: 0 0 IO-APIC-level uhci_hcd > 201: 814161 720175 IO-APIC-level wctdm > 209: 720174 814169 IO-APIC-level wct4xxp > 233: 34 47 IO-APIC-level uhci_hcd > NMI: 1603725 1603680 > LOC: 1603015 1603015 > ERR: 0 > MIS: 0 > [root@pbxtel-01 ~]# > > (this is with the system as it is running now with the backed out to > 1.2configuration) > > Any thoughts? > > Thanks-- Axel.Thimm at ATrpms.net -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 189 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20070522/3aa868d8/attachment.pgp