similar to: chan_capi-cm 0.6.4 random outgoing MSN problem

I'm getting a strange error on one of the two controllers on an AVM C2 card under chan_capi-cm-0.6.3. I have two ISDN controllers defined, both in the same group, both connections are UK ISDN2e Point to Point: On the third outbound call (both of the first two calls are handled by the second controller "ISDN2",) I get this error : chan_capi.c conf_error 0x2001 PLCI=0x301

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

Hi, I like to forward an incoming call on an ISDN line to my mobile phone. Since ISDN offers two channels, I thought that this should work, but Asterisk tells me, that there is no channel available. There is no one else using this line, so guess I made a mistake in the configuration or it might not work for another reason. Here's the CLI output , the capi.conf and extensions.conf. 83086921 is

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Hello list! I have a Asterisk 1.2.10 running using the package from Backports.org for Debian Sarge. I have setup chan_capi (0.6.5 from Backports) and it seems that I am only able to use on B-Channel. When trying to place the second call I get: CAPI INFO 0x34a2: No circuit / channel available capi info shows: Contr1: 2 B channels total, 1 B channels free And capi.conf is: [ISDN1]

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hi, I'm currently using chan_capi-cm-0.6, with the following capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 language=de [ISDN1] msn=8304490 incomingmsn=8304490 isdnmode=msn group=1 controller=1 softdtmf=1 context=demo echosquelch=1 echocancel=yes echotail=64 callgroup=1 devices=2 Each user has a different numer, e.g. 83044910, 83044911, 83044912 and so

Hello, I have read the articles on echo cancellation (http://www.voip-info.org/wiki/view/Asterisk), but couldn't find a solution to my problem. We are running Asterisk 1.4.12 together with an EICON DIVA SERVER BRI-2M PCI (current driver from EICON) and some SNOM 300/360. There are few clients where we recognize echoes on both sides when we call them via ISDN. With some of these clients we

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

Hi, after I fixed my problem with the playback() application, I now have the next strange one. When I dial the number of our client, located in another town, I get a connection to the asterisk server, I can talk to my client or listen to his mailbox. If some in the town of this client calls him, he gets the ISDN error "service not available". Out office is connected to he office

Hi, I tried to use the version 0.6 of chan_capi-cm for outgoing calls it works perfectly but for incoming calls it will not work: --- snip --- *CLI> capi debug CAPI Debugging Enabled -- CONNECT_IND (PLCI=0x101,DID=97,CID=0179903xxxx,CIP=0x1,CONTROLLER=0x1) == reventix: Incoming call '0179903xxxx' -> '97' -- reventix: info element CALLED PARTY NUMBER --

I have installed an Asterisk 1.4 on Suse93 using a FritzCard. Some calls are logged to the ISDN log, but Asterisk is not detecting incoming calls. I wonder whether some other device or process is preventing Asterisk from gaining access to the isdn line? Is there some way to ensure that only Asterisk can listening to the line, or get it to share the line with some other device, such as the fax

Hi all, I am trying to get Capi Dial to use a specific outgoing msn. I can't get it to work. If I make a test call to 0703241494 (same isdn line, just one of the other numbers) I don't get CLID at all. Any ideas? ; use 0703241432 as outgoing msn exten => _070.,1,Dial(CAPI/@0703241432:${EXTEN}|30|r) in capi.conf I have: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/bmp Size: 2918 bytes Desc: Picture (Metafile) Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050307/cb404791/attachment.bmp